FORTIN 78821 Nissan Rogue 2008 Intelligent-Key Remote Starters and Alarm Systems Installation Guide

FORTIN 78821 Nissan Rogue 2008 Intelligent-Key Remote Starters and Alarm

Systems

Product Information

• Product: Nissan Rogue Intellikey
• Model: Rogue Select Intellikey
• Firmware Version: 72.[48]
• Minimum Nissan/Infiniti Bypass Firmware Version: A11
• Product Guide Number: 78821

Product Usage Instructions

1. To add the firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
2. If the vehicle is not equipped with a functional hood pin, set Function A11 to OFF.
3. To program the remote starter option, follow the wiring connections as described in the Wiring Connection Guide on Page 3 / 7.
4. Ensure that the Hood Pin Switch (included) is installed if the vehicle can be remote started with the hood open.
5. This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.
6. Test the wire before connecting it to the steering column.
7. Connect the transponder connector, OBDII, CAN LOW, CAN HIGH, RX, and TX as instructed in the wiring connections guide.
8. Connect the ignition harness, parking lights, accessory, and other necessary connections as described in the wiring connections guide.
9. Cut the loop for automatic transmission mode if applicable.
10. Perform key sense voltage test and tumbler voltage test as described in the product manual.

REGULAR INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

MANDATORY INSTALL | INSTALLATION OBLIGATOIRE

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) A11 MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety  elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

WIRING CONNECTION

1. Ignition harness
   White connector – Back view

2. Transponder connector White connector

3. Drivers kick panel

4. OBDII
   Front view

5. Back vue. 15-pin White connector at BCM, behind glove box.

6. At steering column
   Key sense connector Lt Gray connector Back view

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Remove the valet key from the back of the OEM remote.
Remove the battery from the OEM remote.
Keep the other OEM remotes at least 3 meters (10 feet) away from the vehicle to proceed.

1. Press and hold the programming button:
   Connect the 6-PIN Main harness (White connector).
   The Blue, Red, Yellow and
   Blue & Red LEDs will alternatively illuminate.

2. Release the programming button when the LED is YELLOW.
   If the LED is not solid YELLOW disconnect the 6-Pin connector (Main-Harness) and go back to step 1.

3. Insert the required remaining connectors.

4. Press and release the programming button two (2x) times.
   The YELLOW LED will flash 2 times each second.
   WAIT for the YELLOW LED to turn ON solide.

5. Insert the key in to the Ignition barrel
   The RED LED will turns ON.
   If the YELLOW and RED LED’s are not solid, remove the key and go back to step

6. Repeat this step until the RED and YELLOW LED’s are solid.
   Turn the key to the Ignition ON/RUN position.
   Wait for the BLUE LED to flash rapidly.
   KEY BYPASS PROGRAMMING PROCEDURE 212

7. Turn the key to the OFF position.

8. Turn the key to the Ignition ON/RUN position. 4The BLUE, YELLOW and RED LED’s will rapidly alternate.
   The YELLOW LED begins to flash rapidly: Key bypass programmed.

9. Turn the key to the OFF position.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING

VEHICLE EQUIPPED WITH OEM ALARM
Some vehicles must be UNLOCKED to disarm the OEM alarm before remote start. Enable option D2 using the FlashLink Manager. When this option is enabled the module will automatically UNLOCK before remote start and LOCK after the vehicle has remote started.

REMOTE STARTER FUNCTIONALITY

• All doors must be closed.
• Remote start the vehicle.
• Unlock the doors with either:
  • The OEM remote
  • The remote-starter remote
  • Or the proximity remote
• Enter the vehicle with the Intelligent Access Key.
• The vehicle can now be put in to gear and driven.

If the doors are not unlocked with one of these conditions the module will lock the vehicle’s turn-knob as soon as any door is opened.

Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797

www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>