FORTIN 82041 Nissan Rogue 2008 Intelligent-Key Remote Starters and Alarm Systems Installation Guide

June 13, 2024
FORTIN

FORTIN 82041 Nissan Rogue 2008 Intelligent-Key Remote Starters and Alarm

Systems

Product Information

  • Product Name: THAR-ONE-NIS5 Harness
  • Compatibility: Nissan vehicles (Rogue Intellikey, Rogue Select Intellikey)
  • Function: Immobilizer bypass T-Harness for lock/unlock, arm/disarm, trunk (open), tachometer, parking light,autolight, door status, trunk status, hood status, hand-brake status, and foot-brake status.

Product Usage Instructions

  1. To install the THAR-ONE-NIS5 Harness, follow the wiring connections provided in the user manual.
  2. If your vehicle is not equipped with a functional hood pin, you need to add the firmware version and options using the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).
  3. Set the Hood trigger (Output Status) to “OFF” if your vehicle can be remote started with the hood open by setting function A11 to “OFF”.
  4. The THAR-ONE-NIS5 Harness must be installed by a qualified technician to avoid any wrong connections that could cause permanent damage to the vehicle.
  5. Test the wire before connecting it to the steering column.
  6. Connect the transponder connector and OBDII connector as instructed in the user manual.
  7. Follow the wiring connections provided for ignition, horn, driver door pin, and other components based on the color codes mentioned in the manual.
  8. Cut the loop for automatic transmission mode if applicable.
  9. Connect the T-Harness plug to the corresponding female connector.
  10. Ensure all connections are secure and properly insulated.
  11. Once the THAR-ONE-NIS5 Harness is installed, refer to the user manual for further instructions on using the specific functions and features of the harness.
    Note: It is important to carefully read and understand the entire user manual before proceeding with the installation and usage of the THAR-ONE-NIS5 Harness.

THAR-ONE-NIS5 THARNESS INSTALLATION

FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-
Systems-FIG- \(1\)

FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-
Systems-FIG- \(2\)

MANDATORY INSTALL

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) A11
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-
Systems-FIG- \(6\) FORTIN-82041-Nissan-Rogue-2008
-Intelligent-Key-Remote-Starters-and-Alarm-Systems-FIG-
\(7\)

WIRING CONNECTION

  1. Ignition harness
    White connector -Back view

  2. Transponder connector White connector

  3. Drivers kick panel

  4. OBDII connector Front view

  5. Back vue. 15-pin White connector at BCM, behind glove box.

  6. At steering column
    Key sense connector
    Lt Gray connector Back view

  7. Steering column
    Grey connector – Back view

FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-
Systems-FIG- \(8\) FORTIN-82041-Nissan-Rogue-2008
-Intelligent-Key-Remote-Starters-and-Alarm-Systems-FIG-
\(9\)

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Remove the valet key from the back of theOEMremote.
Remove the battery from theOEMremote.
Keep the other OEM remotes at least 3 meters (10 feet) away from the vehicle to proceed.

  1. Press and hold
    Connect the programming button: the 6-PIN Main harness (White connector).
    The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

  2. Release the programming button when the LED is YELLOW.
    If the LED is not solid YELLOW disconnect the 6-Pin connector (Main-Harness) and go back to step 1.

  3. Insert the required remaining connectors.FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-Systems-FIG- \(11\)

  4. Press and release the programming button two (2x) times.
    The YELLOW LED will flash 2 times each second.
    WAIT for the YELLOW LED to turn ON solide.

  5. Insert the key in to the Ignition barrel.FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-Systems-FIG- \(12\)
    The RED LED will turns ON.
    If the YELLOW and RED LED’s are not solid, the key and go backto step 5.
    Repeat this step until the RED and YELLOW LED’s are solid.
    Turn the key to the Ignition ON/RUN position.
    Wait for the BLUE LED to flash rapidly.

  6. Turn the key to the OFF position.FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-Systems-FIG- \(14\)

  7. Turn the key to the
    Ignition ON/RUN position. The BLUE, YELLOW and RED LED’s will rapidly alternate.
    The YELLOW LED begins to flash rapidly: Key bypass programmed.

  8. Turn the key to the OFF position.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

VEHICLE EQUIPPED WITH OEM ALARM

Some vehicles must be UNLOCKED to disarm the OEM alarm before remote start. Enable option D2 using the FlashLink Manager. When this option is enabled the mod automatically UNLOCK before remote start and LOCK after the vehicle has remote started.

REMOTE STARTER FUNCTIONALITY

FORTIN-82041-Nissan-Rogue-2008-Intelligent-Key-Remote-Starters-and-Alarm-
Systems-FIG- \(17\)

  • All doors must be closed.
  • Remote start the vehicle.
  • Unlock the doors with either:
    • The OEM remote
    • The remote-starter remote
    • Or the proximity remote
  • Enter the vehicle with the Intelligent Access Key.
  • The vehicle can now be put in to gear and driven.

If the doors are not unlocked with one of these conditions the module will lock the vehicle’s turn-knob as soon as any door is opened.

Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT

Tél: 514-255-HELP (4357)

1-877-336-7797

ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTIN User Manuals

Related Manuals