VITEK VT-1311 Hair Dryer Instruction Manual

: June 13, 2024
: VITEK

Table of Contents

VT-1311 Hair Dryer
DESCRIPTION
SAFETY PRECAUTIONS
USING THE HAIRDRYER
PROTECTION AGAINST OVERHEATING
CLEANING AND MAINTENANCE
STORAGE
DELIVERY SET
SPECIFICATIONS
RECYCLING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VT-8215 Hair dryer
Фен
Instruction Manual

VT-1311 Hair Dryer

HAIR DRYER VT-8215
The hairdryer is intended for hair drying and styling.

DESCRIPTION

Nozzle
Body
Detachable air inlet grid
Cool shot button « ****»
Air supply speed switch (0\ \ )
Heating degree switch ( / / )
Hanging loop

ATTENTION! Do not use the unit near water in the bathrooms, showers, swimming pools etc.

When using inside a bathroom, always disconnect the appliance from wall outlet after usage; in particular, unplug power cord from wall outlet, as proximity to water is dangerous even if the appliance is switched off.
For additional protection, it is reasonable to install residual current device (RCD)with rated operating current no higher then30 mA into power supply circuit of your bathroom. Apply to competent specialist for installation.

SAFETY PRECAUTIONS

Before using the electrical unit, read this instruction manual carefully and keep it for future reference.
Use the unit for its intended purpose only, as specified in this manual. Mishandling of the unit may lead to its breakage and cause harm to the user or damage to his/her property.

Before switching the unit on, make sure that the voltage of the mains corresponds to the unit operating voltage.
Never leave the operating unit unattended.
Do not switch the unit on in places where aerosols are sprayed or highly flammable liquids are used.
Hair spray should be applied only after hair straightening is finished.
Always unplug the unit after usage and before cleaning.
When unplugging the unit, pull the plug but not cord.
Do not touch the unit body and the power plug with wet hands.
Do not hang or keep the unit in places where it can fall into a bath or a sink filled with water; do not immerse the unit body, pow er cord or power plug into water or other liquids.
Do not use the unit while taking a bath.
If the unit is dropped into water, unplug it immediately and only then take it out of water.
For children safety reasons do not leave polyethylene bags used as a packaging unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

Do not allow children to touch the unit body, the power cord or the power plug during operation of the unit.
Do not leave children unattended to avoid them using the unit as a toy.
Close supervision is necessary when children or people with disabilities are near the operating unit.
This unit is not intended for usage by children.
During the unit’s operation and breaks between operation cycles, keep the unit away from children.
The unit is not intended to be used by people with physical, sensory or mental dis- abilities (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not
instructed by this person on the usage of the unit.
Do not use the unit when you are drowsy.
Do not use the unit to straighten wet hair or synthetic wigs.
Avoid contact of heated surfaces with your face, neck and other parts of your body.
Do not put the operating unit on heat-sensitive or soft surfaces (for instance, bed or sofa) and do not cover the unit.
It is recommended to unwind the power cord to its full length while using the unit.
The power cord should not:
– touch hot objects;
– run over sharp edges;
– be used as a handle for carrying the unit.
Regularly check the integrity of the power cord.
To avoid damages, transport the unit in the original package only.
Do not use the unit if the power plug or the power cord is damaged, if the unit works improperly and after it was dropped. If the power cord is damaged, it should be replaced by the manufacturer, service or similar qualified personnel to avoid danger.
Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center at the contact addresses given in the warranty certificate and on the website www.vitek.ru.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS AND WORK SPACES IS PROHIBITED.

USING THE HAIRDRYER

After unit transportation or storage at low temperature it is necessary to keep it for at least three hours at room temperature before switching on.

Unpack the unit and remove any advertising stickers that can prevent the unit operation. Unwind the power cord completely.
Before switching the unit on, make sure that your home mains voltage corresponds to the unit operating voltage.
Insert the power plug into the mains socket.

Switching hair dryer on
Before switching the appliance on make sure power supply voltage meets operating voltage of the appliance.

Insert power cord plug into wall outlet.
Select operating speed you need using airflow speed switch (5):
0 – the hairdryer is switched off;
– low speed;
– high speed.
Select airflow temperature you need using heating degree switch (6).
– slight heating;
– medium heating;
– maximal heating;
**** – Cool shot function, press and hold the cool shot button for fixing your hairstyle.

Taking care about your hair
Before drying and setting your hair, wash them with shampoo, dry with towel to remove excessive moisture and brush for better results.
Fast drying
Set switch (6) into position of maximal heating (position ), select airflow speed you need using switch (5) and dry your hair out a little bit. Shake off excessive moisture by hand or using a brush and continuously move the hair dryer over your hair.
Straightening your hair Set switch (6) into position of maximal heating (position ), select airflow speed you need using switch (5) and dry your hair out a little bit. When your hair are almost dry, install concentrating nozzle (1), reduce degree of air heating by switch (6) and airflow speed by switch (5).
Divide your hair in locks and layers, and start straightening them from lower layers upwards. Bruch hair downright using round or flat brush, simultaneously directing hot air blowing from concentrating nozzle on them. Straighten each lock from root to tip this way. After you have finished straitening locks of the lower layer, start processing the locks of medium layer, and so on, and finish with straitening locks of the upper layer.
Natural waving structure of your hair
Set switch (6) into position of slight heating (position ), then set switch (5) into position , hold a lock between your fingers tightly, turn it to direction of its natural curliness, then dry the lock out by directing air jet between the fingers. After getting the shape you need, press cool shot button (4) and fix each lock.
Styling your hair
Set switches (5, 6) into positions of slight heating and slow speed correspondingly, attach concentrating nozzle (1) to provide directed airflow.
Divide your hair into locks and start creating hairstyle you need using round brush for setting hair. While styling, direct airflow straight on your hair in any direction you want.
If necessary, direct air jet on each lock for 2-5 seconds to fix it. Time of setting locks you should determine on your own taking into account type of your hair.
«Cool» air supply
This model has a cool shot button for fixing your hair. Press and hold down the cool shot button (4) « ****» – it enables to keep the created style.

PROTECTION AGAINST OVERHEATING

The appliance is equipped with function of protection against overheating. This function switches the appliance off if temperature of outgoing air is higher then admitted. If hair dryer is switched off during operation, turn it off by setting switch (5) into position «0», take power cord plug out of wall outlet, examine if air inlet or outlet openings are blocked, leave the appliance for a while for cooling down for 5-10 minutes, then switch it on again. Do not block air openings while using hair dryer and avoid your hair getting inside its air inlet opening.

CLEANING AND MAINTENANCE

This hair dryer is intended for household usage only.

It is recommended to remove air inlet grill (3) and clean it from time to time.
Set switch (5) into position «0» and disconnect the appliance from power supply.
Turn the grid (3) counterclockwise and re- move it. Clean the grid with a brush, install the grid back to its place and turn it clockwise until bumping.
Wipe hair dryer housing with damp cloth and wipe it dry afterwards.
Do not use solvents or abrasives for cleaning of the hairdryer body.

STORAGE

Unplug power cord from wall outlet when hair dryer is not in use.
Do not wind power cord around the appliance as doing so may cause cord’s malfunction. Handle power cord carefully, do not pull, twist or stretch it, especially near the plug and the place of connection with appliance housing. If power cord is twisted during operation, straighten it from time to time.
Eyelid for hanging (7) is provided for convenient storage. You can hang the appliance this way on condition there is not any possibility of water dropping on the appliance.
Store hair dryer at a place inaccessible by children.
Keep the hairdryer in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Hair dryer – 1 piece
Concentrating nozzle – 1 piece
Warranty certificate – 1 pc.
Operating manual – 1 piece

SPECIFICATIONS

Power supply: 220-240 V ~ 50-60 Hz
Rated input power: 1850-2200 W
ATTENTION! Do not use the unit near water in the bathrooms, showers, swimming pools etc.

RECYCLING

** For environment protection do not throw out the unit and the batteries (if included), do not discard the unit and the batteries with usual house- hold waste after the service life expiration; apply to specialized centers for further recycling. The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administrate-tion, a disposal service or to the shop where you purchased this product.
The manufacturer preserves the right to change design, structure and specifications not affecting general principles of the unit operation without a preliminary notification due to which insignificant differences between the manual and product may be observed. If the user reveals such differences, please report them via e-mail info@vitek.ru for receipt of an updated manual.
Service life of the unit – 3 years
Guarantee**
Details regarding guarantee conditions can be obtained from the dealer from whom the apply-ance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.
This product conforms to the EMC Directive 2014/30/EU and to the Low Voltage Directive 2014/35/EU.
A production date of the item is indicated in the serial number on the technical data plate. A serial number is an eleven-unit number, with the first four figures indicating the production date. For example, serial number 0606ххххххх means that the item was manufactured in June (the sixth month) 2006.