FORTIN 81941 2009 Toyota Rav4 Regular Key Remote Starters And Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
VEHICLE YEARS
TOYOTA
RAV4 (40-Bit) 2006-2010
81941 2009 Toyota Rav4 Regular Key Remote Starters And Alarm Systems
Vehicle functions supported in this diagram (functional if equipped)
- Immobilizer bypass
- T-Harness available (sold separately)
- Lock
- Unlock
- Arm
- Disarm
- Auto lights shutdown
- Parking Lights
- Tachometer
- Door Status
- Trunk Status
- Horn
- Trunk Release
- Hood Status*
- Foot-Brake Status
- OEM Remote monitoring
| HARDEARE VERSION| BYPASS FIRMWARE VERSION VERSION LOGICIELLE CONTOURNEMENT
79.[65] TOYOTA MINIMUM| To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---|---
| Program bypass option:| UNIT OPTION
C1| DESCRIPTION
OEM Remote status (Lock/Unlock) monitoring
---|---|---|---
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11| | Hood trigger
(Output Status).
---|---|---|---
| Program remote starter option:| FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
2| 4| (+) Start 2 (E1)
(+) Ignition 2(E2)
MANDATORY INSTALL
* HOOD PIN
CONTACT
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE
VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11|
---|---
SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin
and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRNING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
| Press and hold the programming button.
---|---
| Insert the connectors:
20 pin (White),
6 pin (Red),
5 pin (White),
2 pin (White).
(If required)
| Insert the
6-Pin Main connector.
↪ The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
| Release
the programming button when the LED is RED.
If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
| Insert one
functional key into the ignition barrel.
DO NOT turn ON the key.
↪ The RED LED will flash rapidly 10x times.
Key bypass programmed.
If the LED is solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
| Turn the
Ignition to the ON/RUN position.
Wait
↪ The BLUE LED will flash rapidly.
CAN-Bus programmed.
| Turn the
Ignition to the OFF position.
↪ The BLUE LED will turn off.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
This guide may change without notice. See
www.fortin.ca for latest version.
REV.: 20211203
Guide # 81941
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>