FORTIN 93121 Lexus ES 330 2006 Standard Key Remote Starters And Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
93121 Lexus ES 330 2006 Standard Key Remote Starters And Alarm Systems
LEXUS
ES 330
Key 2004-2006
CONFIGURATIONS
Vehicle functions supported in this diagram (functional if equipped)
| 1 | Without doorlocks Sans verrouillage des portes |
|---|---|
| 2 | With doorlocks |
INT-SL + required Avec verrouillage des portes INT-SL+ requis
•| mmobilizer bypass Contournement d’immobilisateur
•| Lock
•| Unlock
•| Arm
•| Disarm
•| Trunk (open)
•| Horn
•| Tachometer
•| Hand-Brake Status
•| Door Status
•| Trunk Status
•| Auto-lights off
•| Parking Lights
To control the doorlocks an INT-SL+ module must be used. (Sold separately)
FIRMWARE VERSION
VERSION LOGICIELLE
79.[65] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or
FLASH LINK MOBILE tool, sold separately. FIRMWARE VERSION
V0.17
INT-SL+
Parts required (Not included)
1x Optional INT-SL+ for door locks Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
| UNIT OPTION | DESCRIPTION |
|---|---|
| A11 |
MANDATORY INSTALL
* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11|
---|---
Notice: the installation of safety elements are mandatory. The hood pin
is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
CONFIG.1 WIRING CONNECTION
CONFIG.2 WIRING CONNECTION
PROGRAMMING PROCEDURE
-
Press and hold the programming button.
-
Insert the connectors:
20 pin (White),
6 pin (Red),
5 pin (White),
2 pin (White).
(If required) -
Insert the 4-Pin (Data-Link) connector.
The LEDs will alternate between BLUE, YELLOW and RED flashes. -
Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1. -
Insert one functional key into the ignition barrel.
DO NOT turn ON the key.
The RED LED will flash rapidly 10x times.
Key bypass programmed.
If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1. -
Remove the key from the Ignition barrel.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
INT-SL PROGRAMMING PROCEDURE CONFIG.2
-
Keep programming button pressed while inserting connector 1.
-
Insert connector 2.
Release the programming button when the LED turns ON. -
Press the lock button on the door.
-
The LED will flash rapidly.
The module is now programmed.
REMOTE STARTER FUNCTIONALITY
| | | | |
---|---|---|---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
the remote-starter remote or the OEM remote.| Insert and Turn the key to the
Ignition ON/RUN position.| Press the brake pedal.| The vehicle can now be put
in to
gear and driven.
www.fortinbypass.com
Module label
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT
PENDING TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>