FORTIN 63831 2007 Dodge Caliber Regular Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
ADDENDUM – SUGGESTED WIRING CONFIGURATION
REGULAR & THAR-CHR5 INSTALLATION
VEHICLE YEARS
DODGE
Caliber 2007
63831 2007 Dodge Caliber Regular Key Remote Starters and Alarm Systems
Vehicle functions supported in this diagram (functional if equipped)
- Immobilizer bypass
- Lock
- Unlock
- Arm
- Disarm
- Tachometer
- Door Status
- Trunk Status
- Hand-Brake Status
- Foot-Brake Status
- OEM Remote monitoring
- R.S. OEM remote Stand Alone compatible
BYPASS FIRMWARE VERSION VERSION LOGICIELLE CONTOURNEMENT 74.[39] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or
FLASH LINK MOBILE tool, sold separately.
Program bypass option:
Program bypass option (If equiped with OEM alarm):
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
| UNIT OPTION | DESCRIPTION |
|---|---|
| C1 | OEM Remote status (Lock/Unlock) monitoring |
| D2 | Unlock before / Lock after (Disarm OEM alarm) |
| A11 | Hood trigger (Output Status). |
Program remote starter option:
Program remote starter option for R.S. OEM REMOTE STAND ALONE:
| FUNCTION | MODE | DESCRIPTION |
|---|---|---|
| 31 | 4 | (+) Parking Light (E1) |
(+) Accessory (E2)
38| 2| Enable
Press 3x Lock to remote start with the OEM remote.
Parts required (Not included)
WIRE TO WIRE DIAGRAM
1x 7.5 Amp. fuse
1x Fusible 7.5 Amp.
THARNESS DIAGRAM
THARNESS THAR-CHR5
1x THAR-CHR
1x THAR-CHR5
MANDATORY INSTALL
* HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11|
---|---
SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin
and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
WIRING CONNECTION
THAR-CHR5
KEY BYPASS PROGRAMMING PROCEDURE
| Press
and hold
the programming button: Connect the 6-PIN Main
harness (White connector).
↪ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---
| Release
the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and
go back to step 1.
| Insert
the required remaining connectors.
| Turn
the key to the
Ignition ON/RUN position.
↪ The BLUE LED will flash rapidly.
| Turn
the key to the OFF position.
↪ The BLUE LED will flash rapidly.
6. With OEM remote
| Press the LOCK button on the vehicles OEM remote.
Without OEM remote
| Press and release the programming button on the once.
| ↪ The
BLUE LED will turn off.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
| |
---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
the remote-starter
remote or the OEM remote.
| |
Insert and Turn the key to the Ignition ON/RUN position.| Press
the brake pedal.| The vehicle can now be put in to gear and driven.
Module label
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
This guide may change without notice. See
www.fortin.ca for latest version.
REV.: 20211215
Guide # 63831
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>