FORTIN 92061 2018 Volkswagen Atlas Regular Key Remote Starters And Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
- FORTIN 92061 2018 Volkswagen Atlas Regular Key Remote Starters And Alarm
- Product Information
- Product Usage Instructions
- INSTALLATION WITH KEY REQUIRED
- MANDATORY INSTALL
- PARTS REQUIRED
- NOTES
- PHOTOS & LOCATIONS
- WIRE-TO-WIRE AUTOMATIC TRANSMISSION WIRING CONNECTION
- THAR-VW6 – AUTOMATIC TRANSMISSION WIRING CONNECTION
- THAR-VW2 – AUTOMATIC TRANSMISSION WIRING CONNECTION
- KEY BYPASS PROGRAMMING PROCEDURE
- REMOTE STARTER PROGRAMMING PROCEDURE
- REMOTE STARTER FUNCTIONALITY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
FORTIN 92061 2018 Volkswagen Atlas Regular Key Remote Starters And Alarm
Systems
Product Information
- Product: Volkswagen Atlas 2018
- Bypass Firmware Version: 61.[12]
- Vehicle Compatibility: Volkswagen vehicles
- Compatible with OEM Remote monitoring and R.S. OEM remote Stand Alone
Parts Required (Not Included)
- 1x Vehicle key
- 1x 7.5 Amp. fuse
- THARNESS THAR-VW6
- THARNESS THAR-VW2
Security Sticker Warning
This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.
Une erreur dans les branchements peut occasionner des dommages.
Program Bypass Option
To program the bypass option, follow these steps:
- Program the functional hood contact option (A11) to OFF if the vehicle can be remote started with the hood open.
Photos & Locations
- Under steering column (+)IGNITION1 (+)IGNITION2
- (+)KEY SENSE
- (+)STARTER
- (~)CAN HIGH
- (~)CAN LOW
- (~)TRANSPONDER WIRE
- OBD-II connector (+)12V BCM (+)FOOT BRAKE
Hood Pin Contact Capot
- Yellow In AA11
- Purple Out AA22
- Purple/White Out AA33
- Green Out AA44
- White Out AA55
- Orange Out AA66
- Orange/Black Out AA77
- Dk.Blue Out AA88
- Red/Blue In AA99
- Lt.Blue/Black In/Out AA1100
- Black In AA1111
- Pink Out AA1122
- Yellow/Black Out AA1133
- Brown/White In AA1144
- (-) Hood pin Pink/Black In AA1155
- Purple/Yellow In/Out AA1166
- Green/White In/Out AA1177
- Green/Red In/Out AA1188
- White/Black Out AA1199
- Lt.Blue In/Out AA2200
Transponder Key
Remove the battery of the key. Wrap 5 to 10 loops around the key or the valet key.
Cut Loop for Automatic Transmission Mode
Coupez la boucle pour le mode transmission automatique.
OBD-II Connector Front View
Connecteur OBD-II Vue de face
- CAN LOW
- CAN HIGH
- (+)FOOT BRAKE
- (+)STARTER
- (+)KEY SENSE
- (+)IGNITION1
- (+)IGNITION2
Product Usage Instructions
- Ensure that the vehicle key and 7.5 Amp. fuse are available for installation.
- If using THARNESS THAR-VW6, follow the specific instructions provided with the product.
- If using THARNESS THAR-VW2, follow the specific instructions provided with the product.
- For programming the bypass option, set function A11 to OFF if the vehicle can be remote started with the hood open.
- Follow the provided photos and locations guide to identify the correct connections under the steering column.
- Connect the necessary wires according to the OBD-II connector front view.
- Install the hood pin contact capot according to the specified color-coded connections.
- Wrap 5 to 10 loops around the transponder key before installation.
- If using automatic transmission mode, cut the loop as instructed.
- Ensure all connections are secure and follow safety precautions.
INSTALLATION WITH KEY REQUIRED
ADDENDUM – SUGGESTED WIRING CONFIGURATION
MANDATORY INSTALL
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
SECURITY STICKER
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
PARTS REQUIRED
WIRE TO WIRE DIAGRAM
- 1x Vehicle key
- 1x 7.5 Amp. fuse
THARNESS DIAGRAM
THARNESS THAR-VW6
- 1x Vehicle key
- 1x THAR-VW6
THARNESS THAR-VW2
- 1x Vehicle key
- 1x THAR-VW2
NOTES
1 KEY REQUIRED FOR THE INSTALLATION
The vehicle’s OEM remote will operate while the engine is running.
PHOTOS & LOCATIONS
WIRE-TO-WIRE AUTOMATIC TRANSMISSION WIRING CONNECTION
THAR-VW6 – AUTOMATIC TRANSMISSION WIRING CONNECTION
THAR-VW2 – AUTOMATIC TRANSMISSION WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
-
Press and hold the programming button: Insert the 6-Pin Main connector.
Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes. -
Release the programming button when the BLUE LED is ON.
If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1. -
Insert the required remaining connectors.
-
Turn the key to the Ignition ON/RUN position.
-
Press and release the programming button once (1x).
The BLUE LED turn off.
Wait,
The BLUE LED will flash rapidly. -
Turn the key to the OFF position.
The BLUE LED will turn off.
The module is now programmed.
REMOTE STARTER PROGRAMMING PROCEDURE
REMOTE STARTER FUNCTIONALITY
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>