FORTIN 46601 Hyundai Tucson 2016 Standard Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
FORTIN 46601 Hyundai Tucson 2016 Standard Key Remote Starters and Alarm
Systems
Product Information
- Product Name: Vehicle Remote Starter Module
- Model: Hyundai Tucson 2016
- Product Code: EMS COM
- Compatibility: Vehicles equipped with a CAN1 and CAN2 network
- Additional Tools: FLASH LINK UPDATER or FLASH LINK MOBILE (sold separately) for firmware version update
Product Usage Instructions
To program the remote starter option, follow these steps:
- Locate the (+) Accessory 2 (E1) wire and connect it to the corresponding wire of the vehicle.
- Ensure the HOOD PIN switch is installed. If the vehicle can be remote started with the hood open, set FUNCTION A11 to OFF.
- Attach the security sticker included in the package.
- IMPORTANT : The installation of this module should only be done by a qualified technician to avoid any damage to the vehicle.
Wiring Connections:
- (+) Ignition:
- Yellow In AA11
- Purple Out AA22
- Purple/White Out AA33
- Green Out AA44
- White Out AA55
- Orange Out AA66
- (-) Horn:
- Orange/Black Out AA77
- Dk.Blue Out AA88
- (~) EMS COM:
- Lt.Blue/Black In/Out AA1100
- (~) PARKING LIGHTS – MUX:
- Green/Red In/Out AA1188
- (+) Accessory 2:
- White Out EE11
- Orange Out EE22
- (+) Accessory:
- Red In EE33
- Black In EE44
- Pink In/Out EE55
- Yellow Out EE66
- (+) 12V:
- Green Vert E3
- (+) Ignition:
- Blue Bleu E5/A1
- (+) Accessory2:
- Green Vert E1
- (+) Starter:
- Red Rouge E6
- (+) Accessory1:
- White Blanc E2
- CAN Connections:
- CAN1 HIGH: Green/Black
- CAN1 LOW: Blue/Black
- CAN2 HIGH: Green/Black
- CAN2 LOW: Blue/Black
Connector Information:
- Black 16-pin connector (M-01 MFS connector at the steering column)
- Blue 6-pin connector (Ignition connector)
- Black 16-pin connector (OBD-II connector)
Note : The presence of the (~) EMS COM wire indicates the presence of an immobilizer in the vehicle. For CAN functions, use programming #2.
Vehicle functions supported in this diagram
(functional if equipped) 
Immobilizer bypass Contournement
- T-Harness available (sold separately)
- Harnais en T disponible
- Lock
- Unlock
- Arm
- Disarm
- Parking Lights
- Trunk (open)
- RAP Disable
- Tachometer
- Door Status
- Trunk Status
- Hood Status
- Hand-Brake Status
- Foot-Brake Status
INSTALLATION
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. __
MANDATORY INSTALL
INSTALLATION OBLIGATOIRE
- HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) A11 MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
Notice : the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
- Press and hold the programming button: Insert the 6-Pin Main connector.
- The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
- Release the programming button when the LED is RED.
- If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
- Insert the required remaining connectors.
- Press and release the programming button seven (7x) times.
- The RED LED will flash 6 times each second.
- Turn the Ignition to the ON/RUN position.
- The RED LED will flash rapidly 10x times. Key bypass programmed.
- The BLUE LED will flash rapidly.
- CAN-Bus programmed.
- Turn the Ignition to the OFF position.
- The BLUE LED will turn off.
PROGRAM: 2 VEHICULE WITHOUT EMS COM WIRE
- Press and hold the programming button:
- Insert the 6-Pin Main connector.
- The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
- Release the programming button when the BLUE LED is ON.
- If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.
- Insert the required remaining connectors.
- Turn the Ignition to the ON/RUN position.
- The BLUE LED will flash rapidly.
- Turn the Ignition to the OFF position.
- The BLUE LED will turn off.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
Notice : Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING: The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used.
FORTIN ELECTRONIC SYSTEMS
assumes absolutely no liability or responsibility whatsoever pertaining to the
accuracy or currency of the information supplied. The installation in every
case is the sole responsibility of the installer performing the work and
FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever
resulting from any type of installation, whether performed properly,
improperly or any other way. Neither the manufacturer or distributor of this
module is responsible of damages of any kind indirectly or directly caused by
this module, except for the replacement of this module in case of
manufacturing defects. This module must be installed by qualifi ed technician.
The information supplied is a guide only. This instruction guide may change
without notice. Visit www.fortinbypass.com to get the latest version.
TECH SUPPORT
Tel : 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>