FORTIN 80631 Mazda CX-9 2014 Standard-Key Remote Starters and Alarm Systems Installation Guide

June 13, 2024
FORTIN

80631 Mazda CX-9 2014 Standard-Key Remote Starters and Alarm Systems

evo logo

REGULAR INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

| “Vehicle functions supported in this diagram (functional if equipped)
---|---
VEHICLE
VEHICULES| YEARS
ANNÉES| 2KEY Programming
Programmation 2 clés| 1KEY Programming
Programmation 1 clé
(Dcryptor)| Immobilizer bypass
Contournement| Lock| Unlock| Arm| Disarm| Tachometer| Parking Lights| Door Status| Trunk Status| Hand-Brake Status|

Foot-Brake Status

MAZDA| OR / OU|
CX-9| 2007-2015| 1| 2| •| •| •| •| •| •| •| •| •| •| •

BYPASS FIRMWARE VERSION

To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.

Program bypass option| UNIT OPTION
OPTION UNITE| DESCRIPTION|
---|---|---|---
| (If equiped with OEM alarm):| D2|

Unlock before / Lock after (Disarm OEM alarm)

|
| IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:| A11| OFF
NON|

Hood trigger (Output Status).

MANDATORY INSTALL | INSTALLATION OBLIGATOIRE

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE
REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

SECURITY STICKER

Notice: the installation of safety
elements are mandatory. The hood pin
and the sticker are essential security
elements and must be installed.

THIS MODULE MUST BE INSTALLED BY A
QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT
DAMAGE TO THE VEHICLE.

This guide may change without notice. See www.fortin.ca for latest version.

DESCRIPTION | DESCRIPTION

parts name

This guide may change without notice. See www.fortin.ca for latest version.

WIRING CONNECTION

wiring connection

KEY BYPASS PROGRAMMING PROCEDURE 1/2 |

1 Make sure to have two valide vehicle key.

2. Release the programming button when the LED is RED.

If the LED is not solid RED
disconnect the 6 Pin
connector (Main-Harness)
and go back to step 1.

3 Insert the required remaining connectors.

4 Turn the first functional key to the ON/RUN position.

Wait 3 seconds or until the security light turns OFF.

5 CAUTION The following step must be completed within 5 seconds. Otherwise disconnect all connectors and go back to step 1.

CONTINUED NEXT PAGE

AUTOMATIC TRANSMISSION

MANUAL TRANSMISSION

Press and hold the programming button until
the LED flashes once than release the programming button.

 The RED LED will flash once (1x)

9 Using a jumper wire, apply power (12v) to the vehicle’s ignition1.

10 The RED LED will flash
rapidly ten (10) times and
after the BLUE LED will
flash rapidly.

Manual transmission: Remove

The module is now programmed.

Use the remote of the remote
starter or security system to test
all of the supported features to
ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE

KEY BYPASS PROGRAMMING PROCEDURE 2/2

7 Turn the Ignition to the ON/RUN position.  The RED and YELLOW LEDs will alternate.

8 Turn the Ignition to the OFF position.

9 Disconnect all connectors and after the 6-Pin (Main-Harness)
or the 4-Pin Data-link connector.

10 Use the tool:
FLASH LINK UPDATER or
11  FLASH LINK MOBILE
to visit the DCryptor menu.

12  AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (Main-
Harness) or the 4-pins (Data-Link) connector
and after all the remaining connector.

REMOTE STARTER / PROCEDURE

The module is now programmed.

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE
MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

remote starter

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular
basis. We recommend that you update this module to the latest firmware and
download the latest installation guide(s) prior to the installation of this product.

Module label

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe
logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case
is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability
or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other
way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be
installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without
notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTIN User Manuals

Related Manuals