TROY LIGHTING B3231 Amado 25.75 Wall Sconce Instruction Manual

: June 13, 2024
: TROY LIGHTING

Table of Contents

FIXTURE INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**TROY LIGHTING B3231 Amado 25.75 Wall Sconce Instruction Manual

**

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONSCOMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALLAPPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIEDFACTORY TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OFCALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDSAFTER USE.
REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THECARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIORTO INSTALLATION FOR ANY DAMAGE TO THEFIXTURE.
DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACTFLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCALELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

FIXTURE INSTALLATION

Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture isdesigned to be mounted on standard round or octagon junction box. The junction box must be securely mountedto the structure of the building.
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO “HOT” WIRE!FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (4). Starting 1″ below the fastener, tightly wrap the connection withelectrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSEDWIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wiressame as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THISCOULD RESULT IN SERIOUS INJURY OR DEATH!
Attach the FIXTURE ASSEMBLY (6) to the MOUNTING PLATE (1) and secure with the SET SCREWS (5).
Put GLASS (7) into the fixture and secure using the SOCKET RING (8) .
Screw the BULB (10) up into the SOCKET of the fixture. B3231 FIXTURE IS RATED FOR 60 WATT LAMP. B3232 FIXTURE IS RATED FOR 75 WATT LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
Restore power to the outlet at the breaker or fuse box.

ITEM	DESCRIPTION	PART NUMBER
1	MOUNTING PLATE	HDW-B3231
2	MOUNTING SCREW	HDW-B3231
3	GROUND SCREW	HDW-B3231
4	WIRE NUT	HDW-B3231
5	M4 SET SCREW	HDW-B3231
6	FIXTURE ASSEMBLY	FAS-B3231, B3232
7	GLASS	GLS-B3231, B3232
8	SOCKET RING	RNG-B3231
9	BULB	NOT INCLUDED