DMX4ALL Pixx Range Extender 5V User Manual
- June 13, 2024
- DMX4ALL
Table of Contents
Pixx Range Extender 5V
For your own safety, please read this user manual and warnings carefully
before installation.
Soldering work may only be carried out by a certified specialist in order to
prevent damage to the product and injury to people.
If acidic or leaded solder, soldering grease or acidic flux etc. has been used
for soldering and/or if the board has been improperly soldered, all warranty
claims will be voided and no repair will be carried out.
Description
The PixxRangeExtender 5V is an optimal tool to bridge longer distances by
using digital LED-Stripes.
Therefore, the PixxRangeExtender 5V is to connect in front to the signal input
of the digital LED-Stripe.
Digital LED-Stripes with separated DATA- and CLOCK-Signal as well as digital
LEDStripes with only one DATA-Signal can be combined with the
PixxRangeExtender 5V.
Data Sheet
Power supply:| 5V from digital LED-Stripe|
---|---|---
Connection:| 3 pin soldering surface
4 pin soldering surface| (Signal-Site)
(Digital LED-Site)
Dimensions:| 23mm x 12mm|
Delivery
1x PixxRangeExtender 5V
1x User manual (german and english)
Connection
Connection between Controller and digital LED-Stripe (CLOCK + DATA)
Connection between two digital LED-Stripes (CLOCK + DATA)
Only digital LED strips with 5V operation voltage of the same type may be
used. Mixing different types is not allowed.
Connection between Controller and digital LED-Stripe (DATA)
Connection between two digital LED-Stripes (DATA)
Only digital
LED strips with 5V operation voltage of the same type may be used. Mixing
different types is not allowed.
Compatible digital LED-Stripes
The PixxRangeExtender 5V is compatible with digital LED strips with only one
signal line or separate signal and data line.
These are for example:
- APA-102
- APA-104
- SK6812
- SK9822
- WS2811
- WS2812(B)
- TM1804
- TM1812
- TM1829
- TLS3001
- TLS3008
- UCS1903
- UCS1904
- UCS1912
- UCS2903
- UCS2904
- UCS2912
CE-Conformity
** This assembly (board) is controlled by a microprocessor and uses high
frequency. In order to maintain the properties of the module with regard to CE
conformity, installation into a closed metal housing in accordance with the
EMC directive 2014/30/EU is necessary.
Disposal
**
Electronical and electronic products must not be disposed in domestic waste.
Dispose the product at the end of its service life in accordance with
applicable legal regulations. Information on this can be obtained from your
local waste disposal company.
Warning
This device is no toy. Keep out of the reach of children.
Parents are liable for consequential damages caused by nonobservance for their
children.
Risk-Notes
You purchased a technical product. Conformable to the best available
technology the following risks should not excluded:
Failure risk:
The device can drop out partially or completely at any time without warning.
To reduce the probability of a failure a redundant system structure is
necessary.
Initiation risk:
For the installation of the board, the board must be connected and adjusted to
foreign components according to the device paperwork. This work can only be
done by qualified personnel, which read the full device paperwork and
understand it.
Operating risk:
The Change or the operation under special conditions of the installed
systems/components could as well as hidden defects cause to breakdown within
the running time.
Misusage risk:
Any nonstandard use could cause incalculable risks and is not allowed.
Warning: It is not allowed to use the device in an operation, where the
safety of persons depend on this device.
WWW.DMX4ALL.DE
DMX4ALL GmbH
Reiterweg 2A
D-44869 Bochum
Germany
Last changes: 08.06.2022
Copyright DMX4ALL GmbH
All rights reserve. No part of this manual may be reproduced in any form
(photocopy, pressure, microfilm or in another procedure) without written
permission or processed, multiplied or spread using electronic systems.
All information contained in this manual was arranged with largest care and
after best knowledge. Nevertheless errors are to be excluded not completely.
It is pointed out that neither a guarantee nor the legal responsibility or any
liability for consequences which are due to incorrect information is assumed.
This document does not contain assured characteristics. The guidance and the
features may be changed at any time and without previous announcement.