BARSKA BC417 Electro Sight Instruction Manual
- June 14, 2024
- BARSKA
Table of Contents
BARSKA BC417 Electro Sight Instruction Manual
Warning: Never attempt to look into the sun with this or any other optical enhancing device. Doing so may cause severe and permanent eye damage. Always follow safe firearm handling procedures when using or handling a firearm.
Mounting
Your M16 Electro Sight has a built in standard 5/8 mount. This
mount will attach your sight to your firearm.
- Loosen the clamp bolts on the mount. Turn counter clockwise.
- Now place the mount on the rail of the riflescope.
- Tighten the bolts but make sure that you do not tighten them all the way.
- Look through the sight and adjust it, by puling the sight forwards and backwards. Do this until the full field of view is in focus.
- Once your able to see the entire field of view tighten the mount all the way.
Battery
The M16 Electro Sight comes equipped with 1 CR1/3N battery. The battery
compartment is located on the mount and is directly under the eyepiece.
Changing the Battery
When your M16 Electro Sight becomes dim or will not light at all:
- Remove the battery compartment cap off, by twisting the cap counter clockwise.
- Once the cap is off and the old batteries have been removed place the new batteries into the compartment positive (+) side up.
- Replace the cap back on and turn clockwise. Ensure that you place the cap on tightly. This will help keep moisture out of the Electro Sight.
Illuminated Reticle
The illumination (IR) button is located under the eyepiece.
ON: Press the button to turn the illumination on.
Change Brightness: Press illumination button and immediately press the
illumination button again to cycle through the brightness settings.
OFF: After setting desired brightness, wait 1 minute then press the
illumination button to turn the illumination off.
Windage and Elevation
You can find the windage on the right side of the sight. This adjusts the
horizontal axis of the sight.
The elevation is located on the top of the sight. This adjusts the vertical
axis of the sight. To access the windage and elevation turrets, remove the
caps that cover the turrets. Turn counter clockwise to loosen the caps. Once
the turrets are exposed, use a small coin to turn the turrets.
Elevation
Turn the turret counter clockwise to raise the reticle, turn the turret
clockwise to lower the reticle.
Windage
Turn the turret counter clockwise to make the reticle move to the right. Turn
the turret clockwise to make the reticle move to the left
1 YEAR LIMITED WARRANTY
BARSKA® Optics, as manufacturer, warrants this new precision optical product to be free of original defects in materials and/or workmanship for the length of time specified by this warranty. This warranty does not include damage caused by abuse, improper handling, installation, maintenance, normal wear- and-tear, unauthorized repairs or modifications and tampering in anyway.
This warranty is limited to the original purchaser and is not transferable.
This warranty applies only to products purchased in the United States of
America and Canada.
In the event of a defect within 30 days, the consumer must return the
defective unit to the BARSKA dealer (the place of purchase) at his/her own
expense.
Beyond 30 days, BARSKA products should be sent to the following address for warranty repairs. Products must be packed carefully and sturdily to prevent damage in transit, and returned freight prepaid to:
BARSKA® OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
For additional and updated information
please visit our website at www.barska.com
Please email info@barska.com or call
1-888-666-6769 for Return Merchandise
Number (RMA#) before any returns.
NOTE: All merchandise received without a valid RMA # will be returned to shipper at his/her own expense.
Please include all of the following when returning BARSKA products for service and/or replacement:
1. Please write your complete details (Name, Address, Telephone #, E-mail
address,
RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $20.00 to cover inspection, shipping and handling.
*Please allow 6-8 weeks for delivery.
This product will either be replaced or repaired at the discretion of the
warrantor. If it’s a discontinued item, we will replace the product with an
equivalent product. Should the repair not be covered by this warranty, an
estimate will be sent for your approval.
Non-warranty repairs or refurbishing of your optical products are always
provided at a reasonable cost.
BARSKA® Optics shall not be liable for any consequential, incidental and/or contingent damages whatsoever. We will not pay shipping, insurance or transportation charges from you to us, or any import fees, duties and or taxes. This warranty supersedes all previous BARSKA® Optics warranties.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>