CLAYPAKY CL2020 Tambora Flash Instruction Manual
- June 1, 2024
- CLAYPAKY
Table of Contents
CLAYPAKY CL2020 Tambora Flash
Specifications
- Product Name: Tambora Flash CL2020
- Manufacturer: Claypaky
- Power Supply: Neutrik PowerCON TRUE1
- Control Signal Compatibility: DMX / Art-Net
- Display: LCD Display
- Connection: Ethernet, 5pin DMX IN/THRU
Safety Information
It is important to carefully read and keep the safety information provided
with the product. For digital access to safety information, visit
www.claypaky.com.
Unpacking and Preparation
Ensure all packing contents are present as shown in Fig. 1.
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Claypaky range,
has been designed and made with total quality to ensure excellent performance
and best meet your expectations and requirements.
SAFETY INFORMATION
IMPORTANT: Claypaky recommends you carefully read and keep the safety
information on this product, also available in digital format at the following
link: www.claypaky.com
Ref: FIS02C – Safety Information Tambora Flash
UNPACKING AND PREPARATION
Packing contents – Fig. 1
INSTALLATION AND START-UP
Fixture overview
Installing the fixture 
Projector installation – Fig. 3
The projector can be installed on the floor resting on specific rubber feet,
on a truss, on the ceiling or wall.
WARNING: the safety chain must be installed except when the projector rests on
the floor. (Code 105041/001 available upon request). This must be secured to
the projector support structure and then hooked to the fastening point at the
centre of the fixture.
Connecting to mains supply 
Connecting the control signal line: DMX / Art-Net 
Connections to the control signal line (DMX) – Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded,
120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use microphone
cable or other cable with characteristics differing from those specified. End
connections must be made using XLR type 5-pin male/female connectors. A
terminating plug must be inserted on the last projector with a resistance of
120 (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal
casing of the connectors. The casing must be connected to the shield braid and
pin 1 of the connectors.
Switching on the fixture and basic SetUp 
Switching on the projector – Fig. 7
Switch-on the fixture. The projector starts resetting the effects. At the same
time, the following information scrolls on the display: 
The control panel (Fig. 7) has a display and buttons for the complete
programming and management of the projector menu.
The display can be in one of two conditions: rest status and setting status.
When it is in the rest status, the display shows the projector’s DMX address.
During menu setting status, after a wait time (about 30 seconds) without any
key having been pressed, the display automatically returns to rest status. It
should be noted than when this condition occurs, any possible value that has
been modified but not yet confirmed with the ENTER key will be cancelled.
Reversal of the display – Fig. 8
To activate this function, press UP and DOWN keys simultaneously while the
display is in the rest mode. This status will be memorised and maintained even
for the next time it will be switched on. To return to the initial state,
repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(addresses from 1 to 512).
The address can also be set with the projector switched off.To activate this
function, press UP and DOWN keys simultaneously while the display is in the
rest mode. This status will be memorised and maintained even for the next time
it will be switched on. To return to the initial state, repeat the operation
all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(addresses from 1 to 512).
The address can also be set with the projector switched off.
Functions of the buttons – Using the menu 
IMPORTANT: To Unlock the display press the buttons sequence UP – DOWN – UP – DOWN – ENTER. USING THE MENU:
- Press MENU once – “Main Menu” appears on the display.
- Use the UP and DOWN keys to select the menu to be used:
- Setup: To set the setting options.
- Option: To set the operating options
- Information: To read the counters, software version and other information.
- Manual Control: To trigger the test and manual control functions.
- Test: To check the proper functioning of effects
- Advanced: Access to the “Advanced menu” is recommended for a trained technical personnel.
- Press to display the first item in the selected menu.
- Use the UP and DOWN keys to select the MENU items.
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can
also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press ENTER to momentarily activate the display and
thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
MAINTENANCE
Periodical cleaning & Caution
CAUTION :
- To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully
with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other
detergent could damage the lenses).
WARNING
- IP66 fixture
- Failure to completely remove power from fixture prior to servicing can lead to serious injury or death.
For additonal service information please contact service@claypaky.it
IMPORTANT
The screws to be removed have rubber sleeve gaskets at the threaded end of the
screw. DO NOT LOOSE these. They must be reinstalled when
reassembly is done. If these rubber sleeve gaskets are damaged, they must be
replaced with exact original equipment (OE) parts, we also suggest to
replace the rubber sleeve gasket every 2 years.
To maintain IP66 rating each cover has rubber gasket on it. If any rubber
gasket is lost or damaged, it must be replaced by an original equipment (OE)
part. We also suggest to replace the rubber sleeve gasket every 2 years.
At the end of maintenance operation it is suggested to use the IP Tester to
verify the IP66 protection
Battery 
This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
DIMENSIONS
CAUSE AND SOLUTION OF PROBLEMS
www.claypaky.com – Service support & Helpdesk: https://e-assist.tech
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>