SelectBlinds Lifestyle Woven Motorized Roller Shades with Cassette Installation Guide
- June 10, 2024
- SelectBlinds
Table of Contents
SelectBlinds Lifestyle Woven Motorized Roller Shades with Cassette
Product Information
The motorized roller shades come in two types: with cassette and with exposed roll. The brackets offer three methods of installation: top-fixing, face- fixing, and side-fixing (only recommended if the width given was taken right at the top of the recess). The outermost brackets should be at least 5cm away fromthe ends of the rail, with any other brackets evenly distributed across the width.
Installation Guide for Motorized Roller Shades with Cassette
The brackets offer two methods of installation: top-fixing and face-fixing. For top-fixing, use the front two holes in the top ofthe bracket to fix to the lintel (the ‘ceiling’ of the recess). For face-fixing, use two screws through the back plate to mount onto a facing surface (a wall or window frame). Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket. Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.
Installation Guide for Motorized Roller Shades with Exposed Roll
We will have positioned the controls where you requested during the ordering
process. However, if you decide to swap the side that they are on, direction
of the roll, or need to trim the blind further, the controls can be removed by
simply unplugging them from the tube. This should be done prior to fixing the
brackets. The brackets offer three methods of installation: top-fixing, face-
fixing, and side-fixing (only recommended if the width given was taken right
at the top of the recess). For top-fixing, where the brackets are screwed into
the lintel (or ‘ceiling’ of the recess), for face-fixing, where the brackets
are screwed onto a facing surface (a wall or window frame), and for side-
fixing, where the brackets are screwed into the side walls of the recess.
Top-fixing or face-fixing are recommended for most installations.
Product Usage Instructions
Situate the T-shaped lip on the top of the cassette into the front lip of the bracket while holding the rail at an angle. Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket. Ensure that the outermost brackets are at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.
Motorized Roller Shades with Exposed Roll
Prior to fixing the brackets, remove the controls by simplyunplugging them from the tube if you decide to swap the side that they are on, direction of the roll, or need to trim the blind further. Locate the depression end (the opposite end to the controls) of the blind into the cross-shaped hole in the corresponding bracket. Lift the control end of the blind and slot the rectangular ‘lugs’ into the corresponding slots on the bracket. Ensure that the outermost brackets are at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.
Fitting the brackets
The brackets offer two methods of installation:
Top-Fixing
Use the front two holes in the top of the bracket to fix to the lintel (the
‘ceiling’ of the recess).
Face-Fixing
Use two screws through the back plate to mount onto a facing surface (a wall
or window frame)
Note that the position of the outermost brackets should be at least 5cm
away from the ends of the rail, with any other brackets evenly distributed
across the width.
Fitting the shade
- Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
- Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.
Before you begin
We will have positioned the controls where you requested during the ordering process. However if you decide to swap the side that they are on, direction of the roll or need to trim the blind further, the controls can be removed by simply unplugging them from the tube. This should be done prior to fixing the brackets.
Fitting the brackets
The brackets ofter three methods of installation:
Top-Fixing
Where the brackets are screwed into the lintel (or ‘ceiling’ of the recess)
Face-Fixing
Where the brackets are screwed onto a facing surface (a wall or window frame)
Side-Fixing
Where the brackets are screwed into the side walls of the recess
Top Tip
Top-fixing or face-fixing are recommended for most installations, whereas
side-fixing is only recommended if the width you gave us was taken right at the
top of the recess.
Fitting the blind
- Locate the depression end (the opposite end to the controls) of the blind into the cross-shaped hole in the corresponding bracket.
- Lift the control end of the blind and slot the rectangular ‘lugs’ into the corresponding slots on the bracket.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>