profi-pumpe SP02114-3 GRANIT-BLACK-2 Solar Fountain Instruction Manual

profi-pumpe SP02114-3 GRANIT-BLACK-2 Solar Fountain

Product Information

The Solar Fountain is a high-quality fountain pump system designed for both outdoor and indoor use. It serves as an eye-catching addition to any garden or space. The product comes with pre-assembled LEDs and a Li-ion battery for uninterrupted operation. The performance of the pump depends on the orientation of the solar panels towards the sun and the intensity of sunlight. Please note that the product does not guarantee optimal performance in shaded areas or on cloudy days.

Product Usage Instructions

1. Unpack all the components of the water fountain and place them on a flat surface.
2. Connect the pump to the water hose.
3. The LEDs are already pre-assembled in the fountain body.
4. Plug the LEDs into the connecting cable using the cableV plugs.
5. If there are multiple LEDs, connect each cable plug to a separate LED as shown in Figure 1.
6. Tighten the closing caps on the LED connectors.
7. Attach the ground spike or wall bracket to the solar panel (refer to picture 2).
8. If there is a protective film on the solar panel, remove it.
9. Position the solar panel to receive direct sunlight. Ensure that it is not shaded, as the Li-ion battery can only function properly under direct sunlight. Adjust the angle of the solar panel if necessary (refer to picture 3).
10. Connect the solar panel to the second connection cable of the pump using the cable plug (refer to picture 1).
11. Tighten the sealing cap.
12. Fill the reservoir with clean water. It is recommended to use distilled water to reduce mineral deposits and bacteria buildup.
13. Before turning on the pump, ensure that there are no kinks in the cable or water hose.
14. Once all connections are complete, place the pump at the bottom of the fountain.
15. Route the power cable to the outside.
16. Fill the fountain with water, ensuring that the pump is completely submerged. Operating the pump without proper water submersion may cause damage.
17. When everything is set up correctly, turn on the pump and the water will start flowing.

Please note that during the first start-up, there may be uneven  water distribution or splashing in the well area. To correct this, check the stability of the fountain and the water flow.

SAFETY INSTRUCTION AND WARNINGS

• Please read the user manual before using the device
• Warning sign

INTRODUCTION

We would like to congratulate you on the purchase of our garden fountain. We appreciate your trust. That‘s why functional security and operational safety stands by us on first place.
To prevent damage to persons or property, you should read this user manual care-fully. Please observe all safety precautions and instructions for proper use of the pump. Failure to follow the instructions and safety precautions can result in injury or property damage.
Please keep this manual with the instructions and safety instructions carefully in order to at any time you can restore them. Please always download the latest version of the user manual of www.profi-pumpe.de under „downloads“. This shall always prevail.

IN GENERAL

The Garden fountains are high-quality fountain pump systems for outdoor or indoor use. The perfect eye-catcher.

• It‘s recommended NOT to conduct yourself technical modifications. First, it is not certain whether these changes are technically correct and, secondly, because no guarantee can be granted.
• Transport damages are immediately to be reported to the package distributor and to us in written form. Failure to give timely notice to the shipping company, and are therefore rejected your claims from the transport company, so we can not accept these claims as well. In your legal obligation to cooperate to minimize damage, we point out expressly herewith.

ASSEMBLY INSTRUCTIONS

• Unpack all the water fountain components from the packaging and lie on a flat surface.

• Connect the pump to the water hose.

• The LEDs are pre-assembled in the fountain body.

• Plug the LEDs to the connecting cable with the cable plugs.

• Connect each cable plug to a LED if there are several as shown in Figure 1.

• Tighten the closing caps on the LED connectors.

• Mount the ground spike or wall bracket to the solar panel (see picture 2).

• Remove the protective film from the solar panel (if existing).

• Position the solar panel to receive direct sunlight. The Li-ion battery can only function if the solar panel is not in the shade. Adjust the angle of the solar panel if necessary (see picture 3).

• Connect the solar panel, using the cable plug, to the second connection cable of the pump (see picture 1).

• Tighten the sealing cap.

• Fill clean water into the reservoir.
  Note : Distilled water is recommended to reduce mineral deposits and bacteria buildup.

• Before turning on the pump, make sure there are no kinks in the cable or water hose

• When installed correctly, the water will begin to flow.

Please note that some water may splash out of the well when the pump starts up for the first time.

IMPORTANT!

Problem : Uneven water distribution or water splashes in the well area.
Correction : During the first start-up, uneven water distribution may appear. In such cases, we recommend checking the stability of the fountain and the water flow.

PERFORMANCE

The performance of the pump depends on the orientation of the solar panels toward the sun and the intensity of. The max. Data obtained under optimal conditions. A feature in the shade or on cloudy days can not be guaranteed. In models with battery Operation depends on the function of the battery is charged.

FROST
Frost can cause damage to the garden fountain and pump. If there is a risk of frost, the garden fountain and the pump must be emptied, rinsed with clean water and stored in a dry place. Then you will enjoy it for a very long time!

MAINTENANCE

• Keep the fountain in good working condition by cleaning it and changing the water every 3 days. Using distilled or purified water will give the best performance.
• If debris is caught in the intake vents of the pump, disconnect the pump from any power sources and rinse the pump under clean running water.
• Before storing the pump in winter it is absolutely important to rinse it with clean water.
• Any dirt particles remaining in the pump will dry out on the pump shaft during the time of storage and cause irreparable damage

If after some time the pump starts losing power or stops working, please clean up sediment  in the pump shell or filter cribs. Kindly note the pump can be opened by pressing down at the bottom of the filter housing. To clear the impeller, open the pump housing at the front by sliding up the front plastic cover

BATTERY INFORMATION

After 12 to 18 months, you should replace the battery. For this purpose open the battery cover and replace the battery with a new. Please find the item number of the replacement battery in section 15. Technical data and order at
https://www.profi-pumpe.de/GARTEN-u-ZIMMER-BRUNNEN/Ersatzteile- Gartenbrunnen:::230_300.html. Please note the limited implied warranty of 6 months.
Important! It must be ensured that the battery cover is properly tightened and watertight.

• With repeated charge and discharge cycles Lead-Acid and NiMh battery packs are less efficient (memory effect).
• This effect is much less pronounced, but still present in small mass in the Li-ion batteries used.
• Through very short and frequent loading operations and many other operational influences batter-ies can age prematurely strong. The batteries are therefore subject to a consumable and wearing part of a shortened warranty of 6 months.
• If you find that the battery will be less efficient, the battery needs to be fully charged. These allow the unit for 2 to 3 days (pump should not be connected) standing in the sun in order to allow a maximum charge the battery or use a suitable external charger. We recommend to occasionally repeat this procedure to extend the battery life.
• If after this recharging the battery still does not meet expectations, you should replace the batteries.

NOTE : The battery is supplied charged. If the state of charge, contrary to expectations, not be sufficient to charge the batteries for at least 8 hours to allow sufficient charging of the battery (so damage the battery to avoid overcharging, the pump must be connected).

WARNINGS ON BATTERY

Lithium Ion cells and battery may get hot, explode or ignite and cause serious injury if they are exposed to abusive conditions, Be sure to follow the safety warnings listed below:

• Do not install the battery backwards, so the polarity is reversed
• Do not connect the positive or/and negative terminal or/and the battery to each other with any meta object, such as wire
• Do not disassemble or modify the battery. The battery contains safety and protection devices which may cause the battery to generate heat, explode or ignite if damaged
• Do not place the battery in or near fire, on stoves or other high temperature locations. Do not place the battery in direct sunlight or use/store the battery inside cars during hot weather. Doing so may cause the battery to generate heat, explode or ignite
• It is not advised for children to handle the battery
• When the battery is worn out, wrap the terminals with adhesive tape or similar materials before disposal
• Immediately discontinue use of the battery, if there is an unusual smell, a change of color or shape, or if it appears abnormal in any other way
• Do not place the battery in microwave ovens, high pressure containers or on cookware facilities
• In the event of the battery is leaking and fluid gets into your eye, do not rub the eye, rinse well with water and immediately seek medical advice. If left untreated, the battery fluid could cause serious injury to the eye

SECURITY TIPS

• Obey absolutely valid regulations on the electrical security
• Never run pump dry
• Pumping inflammable, as well as all other aggressive liquids is prohibited
• Observe water temperature of max. 35°C
• The mains plug must be disconnected before carrying out any work on the garden fountain
• Never pull the pump on the electrical cable or pressure hose
• Avoid cross section narrowing
• During longer unused times, clean the pump, wash it out with clear water, dry and store it at room temperature
• Test wells for enough flowing water (dry run danger)
• The pump must be protected by a residual current circuit breaker with a tripping current of 30 mA.
• The electrical connection must always be carried out by an authorized specialist.
• The pump may be used by children aged 8 years and above as well as persons with reduced physical, sensory or mental abilities or those who lack skills, experience and knowledge only if they are supervised. These aforementioned persons should only use the appliance while adhering to safe instructions and resulting dangers.
• Cleaning and maintenance must not be carried out by children without supervision.
• Under certain circumstances, it is possible that contamination of the water may occur due to lubricants flowing out.
• All solar panels are very sensitive, protect it before all against extremal mechanical influences (shock, vibration, etc.)

The manufacturer explains:

• To take over no responsibility in the case of accidents or damages on the basis of carelessness or disregard to the instruction in this book.
• To reject every responsibility for the damages which original from the improper use of the pump

GUARANTEE REGULATIONS

For all manufacturing and material defects, the statutory warranty applies. In these cases we take the replacement or repair of the device. Shipping costs shall be borne by our company, except as required by law. Please report the warranty on our service platform https://www.profi-pumpe.de/infor-mation.php. We will inform you how to proceed with case-related. Returns please sufficient postage. Unfortunately not prepaid returns can not be accepted because they are filtered out before delivery. Our service we provide in Germany.

The warranty does not cover:

• Material wear (sealing rings, impeller wheels, impeller chambers)
• Unjustified interventions or changes in the pump
• Damages by self fault
• Improper servicing and improper use
• DRY RUNNING (Also partially!) of the pump Moreover, we give no damage compensation for secondary damages!

RECOGNIZING AND REPAIRING OF MISTAKES

Pump runs but no water is en- couraged

| Hose connections systems have a leak| Check hose connection systems
Pump could have a leak| Check pump for moisture damage
Coarsening or fountain nozzles dirty| Disassemble and clean the tube and the fountain nozzle

NOTES ON PRODUCT LIABILITY

We point out, that we are only liable for damages under the Product Liability Act, which are caused by our units if no changes were made to the equipment. If repairs are carried out by our authorized service, we are only liable if original spare parts and accessories were used.

NOTES ON DISPOSAL

• Electro devices of our company, labeled with the symbol of the crossed trash bin, are not permitted to be disposed in your household garbage. We are registered at the German registration department EAR under the WEEE-No. DE79535656.
• This symbol means, that you’re not allowed to treat this product as a regular household waste item – it has to be disposed at a recycling collection point of electrical devices. This is the best way to save and protect our earth.

THANK YOU FOR YOUR SUPPORT!

• In connection with the sale of batteries or with the delivery of equipment containing rechargeable battery packs, the seller is obliged to draw your attention to the following: You are obliged to return used batteries as an end-user. You can return batteries af-ter use to the seller or to the designated collection facilities, which are free of charge (eg: municipal collection points or in stores). You can return the batteries for disposal at no charge to the seller.

EU DECLARATION OF CONFORMITY

The undersigned, Amur S.à r.l., 36, Rue de la Gare, L-5540 Remich, certifies that the product named overleaf, namely GRANIT-BLACK-2 as placed on the market, complies with the relevant provisions listed below, the relevant EU harmonised directives and the EU standard for safety. This declaration of conformity applies insofar as no modifications are made to the product. The sole responsibility for issuing this declaration of conformity lies with the manufacturer.

The sole authorised person to keep the technical documents:
Amur S.à r.l. – 36, Rue de la Gare – L-5540 Remich

EC Electromagnetic compatibility directive (2014/30/EU) The following harmonized standards:

• EN 55014-1: 2017
• EN 55014-2:2015
• RoHS (2011/65/EU)
• EN 62321
• UKCA (2014/30/EU):
  • BS EN 55014-1: 2017
  • BS EN 55014-2:2015

Signed for and on behalf of: Amur S.à r.l. Remich, 26.04.2023
i.V. Dipl. Phys. Peter Neumüller Technical Manager

TECHNICAL DATA

 | ****

English

| ****

Gartenbrunnen GRANIT-BLACK- 2

---|---|---
Solar-Panel| Power| 5V / 2 Watt
Protective class| IP44
Size| 150 x 200 mm
Solar-Battery| Capacity| 3,7V/2000mAh
Battery Typ| Li-Ion

Ersatzteilnr. A4611

Pump| Pump power| 6V / 0,72 Watt
Max. pump capacity| 200 l/h
Max pump height| 80 cm
Max. water temperature| 35 °C
Protective class| IP68
LED| LEDs| 1×4
Brunnen| Dimension (LxWxH)| 34,5 x 34,5 x 82,5 cm
Total weight| ca. 6,5 kg

Please note our disposal advice at section 12.

SPARE PARTS

English|  |
---|---|---
Solar panel|
Power|  | 9 V / 2 Watt
Protective class|  | IP44
Dimension (LxWxH)|  | 190 x 150 x 18mm
Capacity|  | 7.4V/1.2Ah
Battery Type|  | Li-Ion
Pump|
Pump power|  | 1,4 W
Max. pump capacity|  | 250 l/h
Max pump height|  | 90 cm
Max. water temperature|  | 40 °C
Protective class|  | IPX8

The spare parts are available for purchase from AMUR S.à.r.l. at www.profi- pumpe.de
If you need further spare parts, please contact us

Amur S.à r.l.
www.amur.lu
Email : [email protected]
Tel.: (+49) 0611-9 45 87 77-0 Fax: (+49) 0611-9 45 87 77-11

References

• Amur
• Profi-Pumpe.de Ihr Online-Shop für Pumpen und Pumpenzubehör
• Service - Service

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>