profi pumpe 250-7 Submersible Well Pumps Instruction Manual

: June 11, 2024
: profi-Pumpe

Table of Contents

Profi pumpe 250-7 Submersible Well Pumps
Product Usage Instructions
INTRODUCTION
IN GENERAL
RANGES OF APPLICATION
OPERATION
ASSEMBLING
INSTALLATION SCHEME
SECURITY TIPS
GUARANTEE REGULATIONS
RECOGNISING AND REPAIRING MISTAKES
TECHNICAL DATA / TECHNISCHE DATEN
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Profi pumpe 250-7 Submersible Well Pumps

Specifications

Product Name: Submersible Well Pumps (Clear Water)
Versions Available : BRUNNEN-STAR 250-7 (BP01124), BRUNNEN-STAR 550-7 (BP01125), BRUNNEN-STAR 370-7 (BP01126), BRUNNEN-STAR 550-7 (BP01127)
Application : Pumping clear water free of mud, sand, and aggressive chemical substances
Water Filtration: Pre-filter water to 0.2 mm particle size
Intended Use: Domestic water use, water circulation from containers, plain water pumping

Product Usage Instructions

Safety Instructions and Warnings
Please read the user manual before using the device. Ensure to pull the power plug before any maintenance or installation. Be cautious of electrical voltage.
Introduction
Congratulations on purchasing our pump. Functional security and operational safety are our top priorities.
Ranges of Application
The pumps are designed for pumping clear water without mud, sand, or aggressive chemicals. Water may need to be pre-filtered to 0.2 mm particle size. Suitable for domestic water use, water circulation from containers, and plain water pumping.
Operation
Installation should be done by a qualified professional. Check electrical connections and cables for damage before each use. Ensure proper earthing of electrical connections according to regulations. Secure the pump with an RCD circuit breaker with a release current of 30 mA. Avoid cable extensions and ensure sufficient cooling during operation.
Assembling
Assemble pump and motor modules as shown in Figure 1. Tighten screws crosswise and evenly. Mount the filter strainer as instructed.
Installation Scheme
Follow the schematic illustration provided in the offer description for installation. Adhere to country-specific regulations if applicable.
Security Tips
- Avoid cross-section narrowing
- Pay attention to the given particle size
- Clean the pump during long periods of disuse, wash with clear water, dry, and store at room temperature
- Test wells for sufficient flowing water to avoid dry run danger
- The pump must be secured with an RCD circuit breaker with a release current of 30 mA
- All electrical connections should be done by an authorized professional
- Children aged 8 years and above and persons with proper knowledge can use the pump

SAFETY INSTRUCTION AND WARNINGS

Please read the user manual before using the device
Pull power plug
Warning sign
Warning of electrical voltage

INTRODUCTION

We would like to congratulate you on the purchase of our pump. We appreciate your trust. That‘s why functional security and operational safety stands by us on first place.

To prevent damage to persons or property, you should read this user manual carefully. Please observe all safety precautions and instructions for proper use of the pump. Failure to follow the instructions and safety precautions can result in injury or property damage. Please keep this manual with the instructions and safety instructions carefully in order to at any time you can restore them.
Please always download the latest version of the user manual of www.profi- pumpe.de under „downloads“. This shall always prevail.

IN GENERAL

The pumps are developed according to the newest stand of technology, manufactured with much care and go under strict intensive controls. These pumps were optimised by us in particular for the special demands in dirty water areras. Make sure after unpacking the pump that the data given on the type label match with the included operating instructions. In case of doubt the pump is not to be used. Transport damages are immediate to be reported to the package distributor and to us in written form.

RANGES OF APPLICATION

These pumps are made for pumping clear water (free of mud and sand and aggressive chemical substances (see technical data). The water may have to be pre-filtered to 0.2 mm particle size

The pumps are made for the following ranges of applications:

domestic water use from wells with a diameter from 3-inch diameter
circulation of large accumulations of water from containers
Another plain water pumping

IMPORTANT!

The pumps are designed for pumping clean water and chemically non-aggressive liquids. Any guarantee is void in case of improper use. They are not suitable for pumping flammable liquids or for use in places where there is a risk of explosion. The pumps are designed for home use in the house and garden.
These pumps are designed for continuous use provided (max. 20 interruptions per hour). Never run more than 2-3 minutes against a closed valve pump. (Install dry running protection) pump adequately secured against dry running.
The pump must not be used in swimming pools.
Not suitable for use with solar photovoltaic panels.

OPERATION

The installation must be performed by a qualified professional.
Please, check each time before using, the electrical connections and the cables are not damaged. Check before the installation whether the electrical connections are earthed according to the statutory regulations and are installed. The pump is to be secured through an RCD circuit breaker with a release current of 30 mA. Also, it is NOT recommended to perform, for example, a cable extension. It is not certain whether this modification is technically correct, so this warranty is void. It must be ensured that the pump is sufficiently cooled during prolonged operation.

ASSEMBLING

Due to their size, pump and motor modules are delivered partly separately. The assembly is carried out as shown in Figure 1.
Slide the motor shaft into the housing of the pump shaft. Screw the two modules together.
Please make sure that the screws are tightened crosswise and evenly.
Then mount the filter strainer as shown.

INSTALLATION SCHEME

SECURITY TIPS

Obey absolutely valid regulations on the electrical security
Never run pump dry
Pumping inflammable, as well as all other aggressive liquids is prohibited
Pay attention to the medium temperature max. 35°C
Never pull the pump on the electrical cable or pressure hose
Avoid cross-section narrowing
Pay attention to the given particle size
During longer unused times, clean the pump, wash it out with clear water, dry and store it at room temperature
Test wells for enough flowing water (dry run danger)
The pump is to be secured through a RCD circuit breaker with a release current of 30 mA.
The electrical connections are always to be carried out by an authorised professional.
The pump may be used by children aged 8 years and above as well as persons with reduced physical, sensory or mental abilities or those who lack skills, experience and knowledge only if they are supervised. These aforementioned persons should only use the appliance while adhering to safe instructions and resulting dangers.
Cleaning and maintenance must not be carried out by children without supervision.
The pump must not be used or operated under any circumstances when there are people in the same water.
Under certain cirumstances, it is possible that the contamination of water is caused by leakage.

THE MANUFACTURER EXPLAINS:

To take over no responsibility in the case of accidents or damages on the basis of carelessness or disregard to the instructions in this book.
To reject every responsibility for the damages which originate from the improper use of the pump.

SERVICING
Under normal pumping conditions the pump requires no servicing. From an operating period (with clear water) of approx. 2000 hours the mechanical components should be checked: impeller wheels, chambers, sealing rings etc. on wear and if necessary be changed. After 3000 pumping hours the oil in the chamber should also be changed, if necessary (only with oil-dipped engine types!). Please, only fill it up to 80% and check the sealing rings always for density.
With abrasive materials like sand the servicing duration can become shorter.

The following controls should be carried out regularly:

Intactness of the electric cable
That the connection hoses are not bent or broken
Cleanness of the pump medium

Moreover, the pump should be emptied with risk of frost, be washed out with clear water and stored dry.

GUARANTEE REGULATIONS

For all manufacturing and material defects, the statutory warranty applies. In these cases we take the replacement or repair of the pump. Shipping costs shall be borne by our company, except as required by law. Please report the warranty on our service platform http://www.profi-pumpe.de/service.php. We will inform you how to proceed with case-related. Returns please sufficient postage. Unfortunately not prepaid returns can not be accepted because they are filtered out before delivery. Our service we provide in Germany.

The warranty does not cover:

Improper installation (self-installation, unauthorized persons)
Material wear (sealing rings, impeller wheels, impeller chambers)
Unjustified interventions or changes in the pump
Damages by selffault
Improper servicing and improper use
DRY RUNNING (Also partially!) of the pump

Moreover, we give no damage compensation for secondary damages!

RECOGNISING AND REPAIRING MISTAKES

Problem	Possible cause	Solution

Pump runs, no water is being pumped

| Air in the system (cannot es-

cape)

| Air in the system must be let out
Impeller wheel is blocked| Impeller wheel must be cleaned

Pump does not start or swit- ches itself off

| Engine guard has switched the pump off| Pump needs to be cooled
No electricity| Check electrical connections

Pump runs, Pump capacity

slows down or stops

| Pump is inserted to deep| Insert pump not so deep
Hose connections systems

have a leak

| Check hose connection systems
Impeller wheel is worn down| Change impeller wheel
Filter has become dirty| Clean filter

NOTES ON PRODUCT LIABILITY
We point out, that we are only liable for damages under the Product Liability Act, which are caused by our units if no changes were made to the equipment. If repairs are carried out by our authorized service, we are only liable if original spare parts and accessories were used.

NOTES ON DISPOSAL
Electro devices of our company, labeled with the symbol of the crossed trash bin, are not permitted to be disposed in your household garbage. We are registered at the German registration department EAR under the WEEE-No. DE79535656. This symbol means, that you’re not allowed to treat this product as a regular household waste item – it has to be disposed at a recycling collection point of electri-cal devices. This is the best way to save and protect our earth.
THANK YOU FOR YOUR SUPPORT!

EU DECLARATION OF CONFORMITY
The undersigned, Amur S.à r.l., 36, Rue de la Gare, L-5540 Remich, certifies that the product named overleaf, namely 3“/4“ Tiefbrunnenpumpe BRUNNEN-STAR 250-7, BRUNNEN-STAR 550-7, BRUNNEN-STAR 370-7, BRUNNEN-STAR 550-7 as placed on the market, complies with the relevant provisions listed below, the relevant EU harmonised directives and the EU standard for safety. This declaration of conformity applies insofar as no modifications are made to the product. The sole responsibility for issuing this declaration of conformity lies with the manufacturer.

The sole authorised person to keep the technical documents:

Amur S.à r.l. – 36, Rue de la Gare – L-5540 Remich
Low Voltage Directive (2014/35/EU)
Machinery Directive (2006/42/EC)

EC Electromagnetic compatibility directive (2014/30/EU)
The following harmonized standards:

EN ISO 12100:2010, EN 809:1998+A1:2009+AC:2010, EN 60204-1:2006+A1:2009+AC:2010, EN 60335-1:2012+A11:2014+AC:2014, EN 62233:2008+AC:2008,
EN 60335-2-41:2003+A1:2004+A2:2010, EN 60034-1:2010+AC:2010,
EN 55014-1:2006+A1:2009+A2:2011, EN 5514-2:2015, EN 61000-3-2:2014,EN 61000-3-3:2013

TECHNICAL DATA / TECHNISCHE DATEN

English| Deutsch| BP01124| BP01125| BP01126| BP01127
---|---|---|---|---|---
Power Achievement| Leistung| 250 Watt| 550 Watt| 370 Watt| 550 Watt
Max. pump capacity| Max. Fördemenge| 2,8 m³/h| 3,3 m³/h| 4,2 m³/h| 4,2 m³/h
Max. pressure| Max. Druck| 3,2 bar| 5,3 bar| 3,2 bar| 5,4 bar
Max. pump height| Max. Förderhöhe| 32 m| 53 m| 32 m| 54 m
Max. water temperature| Max. Wassertemperatur| 35°C| 35°C| 35°C| 35°C
Max. particle size| Max. Partikelgröße| 0,2 mm| 0,2 mm| 0,2 mm| 0,2 mm
Max. sand content| Max. Sandgehalt| 0,2 %| 0,2 %| 0,2 %| 0,2 %
Protection grade| Schutzklasse| IP58| IP58| IP58| IP58
Electrical tension| Spannung| 230V/50 Hz| 230V/50 Hz| 230V/50 Hz| 230V/50 Hz
Connection pressure side (IT)| Anschluss Druckseite (IG)| 1 1,4” IG| 1 1,4” IG| 1 1,4” IG| 1 1,4” IG
Diameter with cable protection| Durchmesser mit Kabelschutz| 80 mm| 80 mm| 100 mm| 100 mm
Height| Höhe| 81 cm| 105 cm| 68 cm| 75 cm
Weight| Gewicht| 14,5 kg| 15 kg| 15,5 kg| 16 kg
Cable length| Kabellänge| 15 m| 15 m| 15 m| 15 m

The adjacent figure shows an example of the terminal assignment if the mains cable is connected with the correct phase assignment and the co-lours on the pump are also correctly assigned to the corresponding phases.
The electrical wiring diagram must be observed. This switch box is delivered completely assembled and must not be opened.
In the event of malfunctions, the switch box may only be opened by a qualified specialist.

AS A PERFECT COMPLEMENT WE RECOMMEND THE INVERTER PUMP CONTROLLERS FROM PROFI-PUMPE.DE

Automatic demand-oriented switching on and off of pumps
ENERGY-SAVING pump operation: Up to 85% energy and cost reduction for pump operation with alternating load
Ensures constant water pressure in the pipes
Intelligent technology for optimum climate and environmental protection
Pressure reducer function: reduces the maximum pump pressure to the set pressure in the piping system
Minimizes average noise, quiet pump operation
Avoids dangerous pressure surges in the water pipes
Significantly increases the service life of the pump and water pipes
Reduces the risk of flooding due to leaking water pipes
Reliable integrated dry run protection with adjustable auto-start
built-in check valve
intelligent self-monitoring functions
easy commissioning and operation due to preset default values

With an INVERTER pump control from profi-pumpe.de you save over 80% on energy, actively protect the environment and climate and save on electricity costs! In many cases, the purchase is amortized by cost savings in a very short time.

Imprint