ideal lux King SP12 Suspension Lamp Instruction Manual

ideal lux King SP12 Suspension Lamp

Product Information

Specifications

• Brand: King
• Model: SP12
• Maximum Wattage: 12 x 40W
• Voltage: 220-240V, 50/60Hz
• Color Options: Cromo, Oro
• Manufacturer: IDEAL LUX srl
• Address: Via Taglio Destro 32, 30035 Mirano (VE) Italy

Product Usage Instructions

1. Ensure the lighting fitting is installed by a qualified electrician.
2. Follow the assembly instructions by reading the numerical progression provided.
3. This product comes with a replaceable light source. Refer to the legend for details on user-replaceable parts.
4. For safety:
   • Always disconnect the power supply before installation or maintenance.
   • Avoid looking directly at the light source.
   • Use appropriate mounting accessories and comply with safety regulations.
   • If the external power cable is damaged, it should be replaced by the manufacturer, retailer, or a qualified electrician.

FAQ

• Q: Can I replace the light source myself?
  A: Depending on the type of light source, it may be user-replaceable. Refer to the legend for guidance on replaceable parts.

• Q: What should I do if the lamp does not turn on?
  A: Check and replace the fuse if necessary. Always ensure the power supply is disconnected before maintenance.

• Q: How do I ensure electrical safety when using the product?
  A: Follow safety guidelines such as using appropriate mounting accessories, disconnecting power before maintenance, and seeking help from qualified professionals when needed.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
23. Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

ICONE

This product is provided with a light source with effificiency energy class of:

• Replaceable light source by an end-user.
• Replaceable LED light source by an end-user.
• Replaceable light source by authorized personnel only.
• Non-replaceable light source. Upon end of life of the light source, the whole product will be replaced.
• Replaceable control gear by an end-user.
• Replaceable light source by authorized personnel only.
• Upon end of life of the control gear, the whole product will be replaced.

FEATURES

INSTALLATION

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com

IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>