sOmfy 1822649 Izymo On or Off Lighting Receiver Instructions

June 12, 2024
somfy

sOmfy 1822649 Izymo On or Off Lighting Receiver

Safety and liability

Liability

These instructions must be kept by the user. Failure to follow these instructions or use of the product outside its field of application is forbidden and will invalidate the warranty and discharge Somfy of all liability. This Somfy product must be installed by a professional drive and home automation installer. Moreover, the installer must comply with the standards and legislation currently in force in the country in which the product is being installed, and inform his customers of the  operating and maintenance conditions for the product. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. If in doubt when installing this product and/ or to obtain additional information, contact a Somfy representative or visit the website www.somfy.com.

Safety instructions

Never use the product if it is not correctly installed and placed inside a connecting box in conformity with the current norms. Do not use or install this product outdoors. If used with a motor, you should also consult the instructions provided with the motor. Keep the product out of the reach of children. Do not knock or drop the product, expose it to flammable materials or sources of heat or moisture, or splash or immerse it. Keep the product far away from liquids.

Caution : danger of electrocution

Before any installation make sure the power supply is disconnected to avoid any risk of electrocution.

Directly cut the power supply from the breaker box to avoid any risk of electrocution. This product is designed to be used power up, a wrong installation can create a fire or an electric shock. This product must be installed and connected carefully following these instructions. Cut the power supply before any operation and don’t do any modification if the LED is still on.

Product description

The IZYMO LIGHTING RECEIVER Zigbee receiver is a radio micro receiver designed for use in home automation systems operated under Zigbee protocols. It enables the control of one or two lightings in on/off mode via a smartphone or Somfy TaHoma switch. It can also act as a Zigbee router to expand your Zigbee mesh network.

Installation [→Figure A]

Thanks to its compact size, this product can be installed anywhere in the wall or the ceiling (behind an existing wall switch, on the ceiling, etc…).

In detail [→Figure B]

Each terminal can accept a cable of 2.5 mm² maximum, stripped of 8 mm.

Wiring with switch [→Figure C]

Wiring with switch \[→Figure C\]

  1. Switch off the power supply.
  2. Disassemble the wired wall switch controlling the light(s) to be connected.
  3. Wire IZYMO LIGHTING RECEIVER Zigbee according to the diagram.
  4. Reassemble the wired wall switch.
  5. Turn the power back on.
Wiring without switch [→Figure D]
  1. Switch off the power supply.
  2. Wire IZYMO LIGHTING RECEIVER Zigbee according to the diagram.
  3. Turn the power back on.
Auto-detection of switch type

After turning the power supply on, do a single push on the wired wall switch. IZYMO LIGHTING RECEIVER Zigbee has an autodetection system to automatically detect the type of wired wall switch (toggle switch or push-button) wired at the input.

Note: It is possible to combine a toggle switch with a push-button. To perform a new autodetection, IZYMO LIGHTING RECEIVER Zigbee must be manually reset (see 7. Reset to original configuration).

Pairing to TaHoma switch [→Figure E]

IZYMO LIGHTING RECEIVER Zigbee must be power supplied.

  1. Briefly press twice the IZYMO LIGHTING RECEIVER Zigbee Press button: the LED blinks orange.
  2. On the Tahoma application home page, select , choose Lighting & plugs, and then Somfy, and then select Light or Plug as appropriate.
  3. Follow the instructions in the application to complete the configurations.

Tips: It is recommended to perform the set up of the receiver within 15 feet (4.5 meters) of a Zigbee Router.

Unpairing

IZYMO LIGHTING RECEIVER Zigbee must be power supplied and paired.

  1. On the Tahoma application home page, select the receiver to be unpaired.
  2. Follow the instructions in the application to remove the receiver from Tahoma.

Reset to original configuration [→Figure F]

Reset to original configuration \[→Figure F\]

IZYMO LIGHTING RECEIVER Zigbee must be power supplied.

  1. Press more than 5 seconds on the IZYMO LIGHTING RECEIVER Zigbee Press button: the LED blinks orange.
  2. Press once again the Press button (short press) to confirm the reset. If the reset is correct, the LED blinks alternatively in red and green and blinks alternatively in orange. Start again if necessary.
  3. IZYMO LIGHTING RECEIVER Zigbee has now its original settings.

Tips : It is recommended to perform the reset of the receiver within 15 feet (4.5 meters) of a Zigbee Router

Note: To remove the receiver from Tahoma, see Above Unpairing

Symbols

  • N Input Neutral

  • L Input Line

  • Input terminal for the wired switch 1*

  • Input terminal for the wired
    switch 2*

  • Output 1 (controlled by )

  • Output 2 (controlled by )
    *Wired switch optional

Product Specification

Maximum power 110V 230V
LED 48W 100W
Fluorescent 330W 690W
CFL 330W 690W
Incandescent 330W 690W
Various resistive load 330W 690W

Technical data

Power supply 110V – 230V AC on 50Hz/60Hz
Switching capabilities 110V – 230V AC – 2 x 3A
Consumption <1W
RF protocol Zigbee 3.0
Radio frequency range 2.4 GHz
Max output power +11dBm
Range up to 40 m indoors
Operational temperature -4°F to 122°F (-20°C to 50°C
Device ID Type On/Off Light (0x0100)

We care about our environment. Do not dispose of the appliance with usual household waste. Give it to an approved collection point for recycling

IZYMO™ LIGHTING RECEIVER ZIGBEE 1871260A FCC ID: DWNIZYMO-LIGHT

CAUTION

This device complies with Part 15 of the FCC Rules/ Innovation, Science and Economic Development Canada’s licenceexempt RSS (s).Operation is subject to the following two conditions: {l) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/1V technician for help.

Customer Support

Suppliers Name : Somfy Systems Inc.
Suppliers Address (USA): 121 Herrod Blvd, Dayton, NJ 08810, United States of America
Suppliers Website: https://www.somfysystems.com/en-us/contact-us

SOMFY ACTIVITES SA

50 avenue du Nouveau Monde
74300 Cluses FRANCE

www.somfy.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals