SCOSCHE MQ5WDV-1 MagicMount Wireless Charging Phone Holder Instruction Manual
- May 15, 2024
- Scosche
Table of Contents
SCOSCHE MQ5WDV-1 MagicMount Wireless Charging Phone Holder
INCLUDED ELEMENTS
- MagicMount™ Charge5
- Magnetic Wireless
- Charging Mount
- Mounting Adapter
- Window/Dash Mount
- Vent Mount
- MagicPlate™
- Protective Film
- Mounting Template for MagicPlate
- Car Adapter
- Cable Routing Clips (2)
- Cleaning Wipe
DEVICE SETUP
- SECTION A – iPhone® 12 or Later (with optional Mag Safe Case)
- SECTION B – Wireless Charging Smartphones (with Case)
- iPhone® 11 / Pixel 4 & Newer (Case Required)
- Wireless Charging Smartphones (without Case)
- SECTION C – Attaching Device with MagicPlate
- SECTION D – Assembling Window/Dash Mount
- SECTION E – Installing Window/Dash Mount
- SECTION F – Switching Mounting Bases
- SECTION G – Installing Vent Mount
- SECTION H – Connection & Charging
SECTION A
- iPhone 12 or Later (with optional MagSafe Case)
- If using a case, it must be a Mag Safe case (not included) for MagicMount Charge5 to function properly.
Note: MagicPlate is not required. iPhone 12 or Later (without Case)
Note: MagicPlate is not required.
SECTION B
- Wireless Charging Smartphones (with Case) iPhone 11/ Pixel 4 and Newer (Case required*)
- Use the included template to place
- MagicPlate in the correct position.
- Manufacturing materials do not allow adhesives to bond directly to the device.
- Wireless Charging Smartphones (without Case)
- Use the included template to place
- MagicPlate and Protective Film in the correct position.
It is recommended to use the Protective Film. If the MagicPlate needs to be
removed, the film simplifies the process. To remove the MagicPlate use a
credit card and slide in between the film and Magichlate. Do NOT use anything
sharp
or hard as this can damage the device.
SECTION C
SECTION D
Window/Dash Mount
Assembly
Charging Mount
Adjustment
(Window/Dash Mount only)
Loosen the ball-joint collar to adjust the angle or rotate the mount 360°.
SECTION E
Window/Dash Mount
Installation
-
Clean the mounting surface using a supplied wipe
-
Remove the protective film from the StickGripm suction cup base.
-
With the lever in the UP position, place the mount on the surface and press the lever down to lock it in place.
-
Supplied cleaning wipes may cause discolouration of certain plastics, vinyl and painted surfaces. It is recommended to test in an inconspicuous area first.
Note: StickGrip suction cup may leave residue or discolouration on some surfaces. -
It may also leave a ring of residue when mounted to the dash.
-
To renew and reuse the StickGrip mounting base, rinse it under warm water and allow it o air dry.
SECTION F
Switching Mounting Bases (Window/Dash Mount to Vent Mount)
- Pull the release tab out on the mounting adapter, and slide the t-notch hitch down.
- Remove the t-notch hitch from the opening on the back of the mount head.
- Insert the top-notch hitch on the vent mount into the opening on the back of the mount head.
- Slide t-notch hitch upward.
SECTION G
Vent Mount Installation Rotate vent clips on the mount to align with the vent
Note : Works with many vent designs. Not compatible with curved or
circular vents.
SECTION H
- LED Status Indicator
- Blue: Charging
- Flashing Red: Foreign Object
- Detected (FOD)
- Wireless Charger*
- Input: 12.0. 2.0A
- Output: 15.0W/10.0W/7.5W/5.0W depriving change destine and environmental conditions.
Car Adapter
Input: 12.0V-24.0=- 2.5A
DC Output: 11.7V—2.0A
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interterence by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canadian Compliance Statement
This device contains license-exempt transmitters)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This Class [B]
digital apparatus complies with Canadian ICES-003. CAN ICES-3 (B)/NMB-3(B)
MagicMount CHARGES
SCOSCHE
Scosche Industries
1550 Pacific Avenue
Oxnard, Califomia 93033
Phone: 800-363-4490 x1 /
805-486-4450 x1
www.scosche.com
2023 Scosche Industries
Scosche, MagicMount, MagicPlate, and StickGrip are all trademarks of Scosche
Industries. Other marks or brands are the property of their respective owners.
Devices and or appearance may vary.
Designed in Oxnard, California SI MQ5WDV 10/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>