DELTECH FITNESS DF5200 8 Pair Vertical Dumbbell Rack Instruction Manual
- June 12, 2024
- DELTECH FITNESS
Table of Contents
DELTECH FITNESS DF5200 8 Pair Vertical Dumbbell Rack
Product Information
- Product Name: DF5200 8 PAIR VERTICAL DUMBBELL RACK
- Assembly Manual: Included
- Assembly Video: Available (Scan the QR code below on your phone’s camera to access the video)
- Contact Number: 888-258-0533
Product Usage Instructions
-
Step 1: Check the box contents:
- A – Body Assembly (1 quantity)
- B – Base (1 quantity)
- C – 10mm Bolt (6 quantity)
- D – 10mm Locknut (6 quantity)
- E – Plastic Protector (32 quantity)
- F – Locking Pin (32 quantity)
-
Step 2: Tools required:
- Metric Wrenches or Socket Set
- 4mm Hex Wrench
-
Step 3: Assemble one side of the Body Assembly (A) to the Base (B) using the 10mm Bolts (C) and 10mm Locknuts (D).
-
Step 4: If necessary, the Body Assembly is designed to be flexible and can easily move to line up the other 3 holes. Once aligned, attach using the remaining 10mm Bolts and 10mm Locknuts.
-
Step 5: To install Plastic Protectors (E), slide them down onto the edge of the rack. Rotate them clockwise and slide them backwards until the hole in the Protector lines up with the hole in the Dumbbell Rack.
-
Step 6: Insert the Locking Pin (F) into the hole of the Plastic Protector and through the hole in the Dumbbell Rack. Push it until it locks into place.
Safety Notice: For your safety, please read all instructions carefully. If you are missing any hardware or have any fit-up problems, please contact Deltech Fitness toll-free at 888-258-0533.
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE
CONTACT DELTECH FITNESS TOLL FREE
888-258-0533
BOX CONTENTS
HARDWARE
NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE 888-258-0533
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET 4MM HEX WRENCH
INSTALLATION
- ASSEMBLE ONE SIDE OF THE BODY ASSEMBLY (A) TO THE BASE (B) USING 10MM BOLTS (C), AND 10MM LOCKNUTS (D).
- THE BODY ASSEMBLY IS DESIGNED TO BE FLEXIBLE, IT WILL EASILY MOVE TO
- LINE UP THE OTHER 3 HOLES IF NECESSARY. ONCE IT IS ALIGNED, ATTACH USING THE REMAINING 10MM BOLTS, AND 10MM LOCKNUTS.
- TO INSTALL PLASTIC PROTECTORS (E), SLIDE DOWN ONTO EDGE OF RACK. ONCE IT IS ON, ROTATE CLOCKWISE AND SLIDE BACKWARDS UNTIL HOLE IN PROTECTOR LINES UP WITH HOLE IN DUMBBELL RACK
- INSERT LOCKING PIN (F) INTO HOLE OF PLASTIC PROTECTOR AND THROUGH HOLE IN DUMBBELL RACK AND PUSH UNTIL IT LOCKS INTO PLACE.
SAFETY NOTICE
WARNING : THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES
- BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
- STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM, PROPER STRETCHING WILL PREPARE YOUR JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
- IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
- DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING NEVER WORK OUT ALONE ALWAYS HAVE A PARTNER.
- SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT LOOSENED.
- WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
- DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WITCH COULD BECOME ENTANGLED IN MOVING PARTS.
- DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
- KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
- CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
- REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND LIABILITIES BECOME VOID.
Assembly Video Available
Simply scan the QR code below on your phone’s camera to access the video
