muse MT-120 MB Home Audio System User Manual

MT-120 MB Home Audio System

User Manual

Please read the instructions carefully before operating the unit.

TURNTABLE MICRO SYSTEM

LOCATION OF CONTROLS

1. TUNING knob
2. USB port
3. STANDBY indicator
4. STANDBY button
5. FUNCTION button
6.   / P- : PREV button/ Preset stations-
7. / P+ : NEXT button/ Preset stations+
8.   / ATS : PLAY/ PAUSE button; Auto scan and preset radio stations
9. STOP button
10. REC (RECORD) button
11. BLUETOOTH indicator
12. REC (RECORD) indicator
13. To open/ close disc tray
14. VOLUME control
15. FM wire antenna
16. Phones jack
17. AUX IN jack
18. LINE OUT: External device output jack
19. POWER ON/OFF switch
20. DC IN 12V jack
21. Speaker terminals
22. Speaker terminals
23. 45RPM adaptor
24. Platter
25. Speed selector (33/45/78)
26. Tone arm
27. AUTO STOP (ON/OFF) Switch
28. Tone arm rest
29. Cartridge with stylus
30. Spindle
31. Lift lever

SPEAKER CONNECTION

1. Insert the speaker cables by pushing down the terminal lever of the Left Speaker Terminal
and the Right Speaker Terminal.
2. Connect the speaker to Speaker Terminals, with BLACK wire to BLACK terminals and RED wire to RED terminals

A. Push Speaker terminal tab down to insert wire.

B. Release tab to lock wire in the terminal.

POWER SUPPLY

Using the AC adaptor
AC adaptor:
Input: 100-240V 50/60Hz 1.5A
Output: 12.0V 3.0A

The supplied AC adaptor is suitable for use on AC main supplies of 100-240V and should
only be connected to a mains supply within these parameters.
In a concern of saving energy, when playback has reached to the end or listening volume is set at a very low level and no control is operated on the device for a period of 10 minutes, the unit will automatically switch to Standby mode.

Cautions:

• The AC adaptor included with this unit is for its use only. Do not use it with other equipment.
• Turn off the unit before unplugging the AC adaptor from the unit so as to avoid the unit being damaged.
• When the unit is not going to be used for long time, disconnect the AC adaptor from the AC outlet.
• Be sure to use it near the wall outlet and easily accessible. If a malfunction occurs, disconnect the plug from the wall outlet at once.
• AC adaptor is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the AC adaptor of the apparatus shall be disconnected from the mains socket outlet completely.
• Never use an AC adaptor that is damaged, route power lead in a safe manner and make sure it is not subjected to trapping or pinching. If the power lead is damaged refer to a qualified service agent.

TURNING ON/OFF THE UNIT

1. To slide the POWER ON/OFF switch to “ON” position on back of unit to go to the standby mode, the STANDBY indicator turns RED, then press STANDBY button to turn the unit ON.
2. To power off the unit, press the STANDBY button, then slide the POWER ON/OFF switch to “OFF” position on back of unit.

SELECTING FUNCTION

The function (FM/ CD/ USB/ PHONO/ AUX/ BLUETOOTH) is selected by pressing FUNCTION button repeatedly.

LISTENING TO THE RADIO

1. When the unit is on, press FUNCTION button to select the FM mode until FM indicator
   appears on display

2. Fast rotate TUNING knob clockwise or anti-clockwise. The radio will automatically search a station upward or downward and stop at a strong station.

3. Adjust the volume to the desired level.

Automatic storage
Press and hold ATS for few seconds and the unit will automatically save the first 20 FM stations. When you store on a channel already been preset, the previous station will automatically be cleared and replaced by the new station.

Listen to the station presets

1. Press P- / P+ and repeat the operation as many times as necessary to select your station.
2. Adjust the VOLUME to the desired level.

LISTENING TO THE CD DISC/ MP3

1. When the unit is on, press FUNCTION button to select the CD mode until CD indicator
appears on display.
2. Press to open the disc tray. Display shows ”OPEN”, Insert a disc with label side facing up. Press again to close the disc tray. The display will show “–“ for few seconds.
3. The total number of track will appear on display and playback starts automatically.
4. Press to skip forward to the next track or press repeatedly to skip several tracks. Press return to the beginning of the track, or press repeatedly to skip backwards several tracks.
Press and hold or to search quickly within a track.
5. Press to suspend momentarily the track playback. Press again to resume playback.
6. Press to stop the playback.

USB PLAYBACK

1. Connect a USB device containing MP3 files or MP3 player to the USB port.

2. When the unit is on, press FUNCTION button to select the CD mode until CD indicator
   appears on display.

3. Adjust the VOLUME to the desired level.

4. Press to skip forward to the next track or press repeatedly to skip several tracks. Press
   return to the beginning of the track, or press repeatedly to skip backwards several tracks.
   Press and hold or to search quickly within a track.

5. Press to suspend momentarily the track playback. Press again to resume playback.

6. Press to stop the playback.

Removing the USB device

Please be sure to stop playback and turn the unit OFF before removing the USB device to avoid damaging the USB and system.

Note

• There are many USB devices in the market. We cannot guarantee to support all different
  models. Please try another USB device if yours is not supported.

• The unit might not support all the multimedia files stored in USB because it includes some special playback procedure which might not be compatible with the procedure of this unit.

LISTENING TO THE PHONO

1. When the unit is on, press FUNCTION button to select the phono mode until PHONO indicator appears on display.
2. Remove the stylus cover from the stylus and release the Tone arm rest.
3. Place a record on the turntable platter and select the desired speed (33/45/78) according to
the record.
NOTE: If you are playing 45RPM singles, place the 45 RPM adapter on the center spindle.
4. Push up the lift lever to raise the tone arm and gently move the tone arm to the desired
position onto the record, push down the lift lever, move the tone arm slowly onto the record
to start playing the record.
5. Adjust the VOLUME control to your desired level.
6. If the AUTO STOP ON/OFF Switch is turned ON, the record will stop automatically when
playback ends. If Auto Stop switch is turned OFF, record will not stop automatically when
playback ends.
Remark: Certain types of records may have an auto-stop area outside the preset limit, so the
turntable may stop before the last track finishes. If this occurs, set the AUTO-STOP switch to
the “OFF” position. This allows the record to play to the end, but please note that it will not stop automatically. You must manually raise the tone arm and place it back in the rest and then turn off the power to prevent the turntable from spinning.
IMPORTANT: Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm Clamp could cause damage to the Tone Arm or Stylus.

CONNECTING AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack (3.5mm) on back of unit. (cable not included).
2. Press FUNCTION button repeatedly to select AUX mode until “AU” indicator appear on
display.
3. Start playback from your auxiliary source.
4. Adjust the VOLUME to desired level.
5. To stop playback, disconnect your auxiliary source from the AUX IN jack.

BLUETOOTH FUNCTION

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Pairing a Bluetooth Device

1. When the unit is ON, press FUNCTON button repeatedly to select Bluetooth mode. The
display will show “ ” for a few seconds. The Bluetooth indicator will start to blink rapidly
2. On the Bluetooth device, enable Bluetooth and select “MUSE MT-120 MB” from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) You will hear an indication voice when pairing is successful.
Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, you need to disconnect current device first and follow the steps above to make a new connection.
• On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose “Use as Audio Device (stereo)” or similar.
• Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
• When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

1. With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the MT-120 MB’s speakers.
2. Press the button to pause playback. Press again to resume playback.
3. Select desired track with / .
4. Adjust the volume using the VOLUME buttons. You can also adjust the volume on the device to which you are paired.

RECORDING THE PHONO

1. Connect the USB device to the USB port (Make sure the USB device have enough space to
save the encoding).
2. Follow procedures 1 to 6 in LISTENING TO THE PHONO section. Press the REC button, the REC indicator lights up and ”USB” icon flashes, then recording will start.
3. Press to stop encoding, REC indicator lights off.
4. To listen the recording, repeatedly press FUNCTION button to select the USB mode until
USB indicator appear on display, and press / to find the last file in the USB, then the
playback starts automatically.

RECORDING THE AUX IN

1. Connect the USB device to the USB port (Make sure the USB device have enough space to
save the encoding).
2. Follow procedures 1 to 5 in CONNECTING AUXILIARY SOURCE section. Press the REC button, the REC indicator lights up and ”USB” icon flashes, then recording will start.
3. Press  to stop encoding, REC indicator lights off.
4. To listen the recording, repeatedly press FUNCTION button to select the USB mode until
USB indicator appear on display, and press / to find the last file in the USB, then the
playback starts automatically.

RECORDING THE BLUETOOTH

1. Connect the USB device to the USB port (Make sure the USB device have enough space to
save the encoding)
2. Follow procedures 1 to 4 in Using a Bluetooth Device section. Press the REC button, the REC indicator lights up and ”USB” icon flashes, then recording will start.

3. Press  to stop encoding, REC indicator lights off.
4. To listen the recording, repeatedly press FUNCTION button to select the USB mode until
USB indicator appear on display, and press / to find the last file in the USB, then the
playback starts automatically.

RECORDING THE CD

1. Connect the USB device to the USB port (Make sure the USB device have enough space to
save the encoding).
2. Follow procedures 1 to 6 in LISTENINGTOTHECD DISC/ MP3 section. Press the REC button, the REC icon lights up and ”ONE” icon appears in display.

3. Press / to choose ONE (single CD song recording) or ALL (whole CD recording).
– Single CD song recording:
Choose ”ONE” icon appears on display, press the REC button to confirm the recording.
The display will appear the “01”, then press / to select the song to be recorded,