DELTECH FITNESS DF832 Linear Bearing Smith Machine Instruction Manual
- June 12, 2024
- DELTECH FITNESS
Table of Contents
DELTECH FITNESS DF832 Linear Bearing Smith Machine
Product Information
The DF832 PEC Attachment is an accessory for the Lat Machine. It includes various components for assembly, such as arm mounts, pulley brackets, cams, backrest pad, arms, cables, and hardware. The attachment allows for targeted chest exercises and pec fly movements.
Product Usage Instructions
- Before starting assembly, ensure you have all the necessary components mentioned in the “BOX CONTENTS” section.
- Refer to the assembly video specific to your model, which can be accessed by scanning the QR code provided in the manual.
- Assemble the arm mount (A) and the swivel pulley mount bracket (D) to the front support of the Lat Machine using the M12 x 75MM bolts (M), M12 flat washers (V), and M12 lock nuts (Z).
- Install the cams (E, F) on the arms (J, K) by inserting large bushings (N) on each end of the tube. Ensure correct installation by referring to the diagram.
- Insert large bushings (N) into the arm mount (A). Assemble the weight arms to the arm mount (A) using the M19 lock nuts (Y).
- Install the swivel pulley assemblies to the mount bracket using the M12 x 170MM bolts (Q), M12 washers (V), small bushings (O), and M12 lock nuts (Z).
- For fixed pulley installation, use the 3-1/2 pulleys (P) and follow the instructions provided in the manual.
- Assemble the backrest pad (I) to the front support of the Lat Machine using the M10 x 70MM bolts (R) and M10 flat washers (W). Install the fixed pulley assembly using the M10 lock nuts (AA).
- Attach the pec cable to the left side cam using the M10 x 25MM bolt (W), M10 washers (W), and M10 lock nut (AA). Refer to Figure A for guidance.
- Run the cable through the left side swivel pulley, down through the floating pulley, up through the right side swivel pulley, and attach it to the right cam.
- Ensure there are adjustment holes on each cam to compensate for cable stretch after using the machine for a while.
If you encounter any missing hardware or fit-up problems during assembly, please contact Deltech Fitness at 888-258-0533 for assistance.
ASSEMBLY VIDEOS AVAILABLE
Click on the QR Code below for your model to access the assembly video
- DF910– Lat Machine
- DF908– Stack Loaded Lat Machin
BOX CONTENTS
HARDWARE
ARM & PULLEY MOUNT INSTALLATION
TOOLS REQUIRED
WRENCHES OR METRIC SOCKET SET
ASSEMBLE THE ARM MOUNT (A) AND THE SWIVEL PULLEY MOUNT BRACKET (D) TO THE
FRONT SUPPORT OF THE LAT MACHINE USING THE M12 x 75MM BOLTS (M), M12 FLAT
WASHERS (V) AND M12 LOCK NUTS (Z)
NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS SO YOU MUST USE A
WRENCH TO TIGHTEN THE BOLT. THE BOLT MUST GO THRU THE PLASTIC INSERT IN THE
NUT.
CAM & ARM PAD ASSEMBLY
INSTALL THE CAMS (E,F) ON THE ARMS (J,K), INSERTING LARGE BUSHINGS (N) ONEACH END OF THE TUBE. THERE IS A LEFT HAND AND A RIGHT HAND SIDE SO YOU WILL NEED TO LOOK AT THE DIAGRAM TO ENSURE CORRECT INSTALLATION
ARM INSTALLLATION
INSERT LARGE BUSHINGS (N) INTO THE ARM MOUNT (A). NOW ASSEMBLE THE WEIGHT ARMS TO THE ARM MOUNT (A) USING THE M19 LOCKNUTS (Y)
SWIVEL PULLEY ASSEMBLY
ASSEMBLE THE 3 ½” PULLEY (P) INTO THE SWIVEL PULLEY BRACKET (C) USING THE M10 x 45MM BOLT (S), M10 WASHERS (W), AND M10 LOCKNUT (AA). REPEAT FOR OTHER SWIVEL PULLEY ASSEMBLY. INSTALL SMALL BUSHINGS (O) INTO EACH END OF TUBE.
SWIVEL PULLEY INSTALLATION
INSTALL THE SWIVEL PULLEY ASSEMBLIES TO THE MOUNT BRACKET USING THE M12 x 170MM BOLTS (Q), M12 WASHERS (V), SMALL BUSHINGS (O), AND M12 LOCKNUTS (Z).
FIXED PULLEY ASSEMBLY
INSTALL THE 3 ½” PULLEY(P) INTO THE FIXED PULLEY BRACKET (B) USING THE M10 x
45MM BOLT (S) M10 WASHERS (W), AND M10 LOCK NUT (AA).
NOTE: IF INSTALLING ON DF908, USE 4-1/2” PULLEY.
FIXED PULLEY & BACKREST INSTALLATION
- ASSEMBLE THE BACKREST PAD (I) TO THE FRONT SUPPORT OF THE LAT MACHINE USING THE M10 x 70 BOLTS (R) AND THE M10 FLAT WASHERS (X). (THE BOLTS SCREW INTO THREADED INSERTS PRE-INSTALLED IN THE BACK PAD)
- NEXT INSTALL THE FIXED PULLEY ASSEMBLY USING THE M10 x 70MM BOLTS (R) M10 FLAT WASHERS (W), AND M10 LOCKNUTS (AA).
FLOATING PULLEY ASSEMBLY
ASSEMBLE THE 3 ½” PULLEY (P) TO THE FLOATING PULLEY BRACKET (G) USING THE M10 x 45MM BOLT (S), M10 WASHERS (W) AND M10 NUT (AA).
PEC ATTACHMENT CABLE INSTALLATION
- ATTACH THE PEC CABLE TO THE CAM ON THE LEFT SIDE USING THE M10 x 25MM BOLT (W), M10 WASHERS (W) , AND M10 LOCKNUT (AA). (SEE FIGURE A)
- NOTE: THERE ARE ADJUSTMENT HOLES ON EACH CAM TO COMPENSATE FOR CABLE
- STRETCH AFTER THE MACHINE IS USED FOR A WHILE.
- RUN THE CABLE THROUGH THE LEFT SIDE SWIVEL PULLEY, DOWN THROUGH THE
- FLOATING PULLEY, UP THROUGH THE RIGHT SIDE SWIVEL PULLEY AND ATTACH TO RIGHT CAM.
- TIGHTEN THE BOLTS ON THE SWIVEL PULLEYS.
INSTRUCTIONS FOR INSTALLING ON DF838– STACK LOADED LAT ATTACHMENT
REMOVE THE THE 4-1/2” PULLEY FROM THE CENTER FLANGES OF THE BOTTOM SUPPORT AND REPLACE WITH 3-1/2” PULLEY.
DF838 FLOATING PULLEY ASSEMBLY
- REMOVE THE 4-1/2” PULLEYS FROM THE FLOATING PULLEY ASSEMBLY AND
- REPLACE WITH 3-1/2” PULLEYS, MAKING SURE TO INSTALL THE LOWER
- BOLT IN THE HOLE SPECIFIED IN THE DIAGRAM ABOVE.
DF838 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC USING THE CHAIN AND SPRING CLIPS PROVIDED.
DF908 FLOATING PULLEY ASSEMBLY
- INSTRUCTIONS FOR INSTALLING ON
- DF908– STACK LOADED LAT MACHINE
MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM ABOVE.
DF908 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC WITH SPRING CLIP.
DF830 FLOATING PULLEY ASSEMBLY
INSTRUCTIONS FOR INSTALLING ON DF830– LAT ATTACHMENT
MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM ABOVE.
DF830 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC USING THE CHAIN AND SPRING CLIPS PROVIDED.
DF910 FLOATING PULLEY ASSEMBLY
INSTRUCTIONS FOR INSTALLING ON DF910– LAT MACHINE
MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM ABOVE.
DF910 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT SUPPORT AND REMOVE CHAIN. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC USING SPRING CLIP. MOVE CHAIN TO UPPER CABLE AND CONNECT TO WEIGHT CARRIAGE.
SAFETY NOTICE
WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES:
- BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
- STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
- IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
- DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER WORK OUT ALONE- ALWAYS HAVE A PARTNER.
- SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT LOOSENED.
- WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
- DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH COULD BECOME ENTANGLED IN MOVING PARTS.
- DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
- KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
- CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
- REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND LIABILITIES BECOME VOID.
NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE 888-258-0533.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>