Deltech Fitness DF830 LAT Attachment Instruction Manual

: June 12, 2024
: DELTECH FITNESS

Table of Contents

Deltech Fitness DF830 LAT Attachment
Product Information
Product Usage Instructions
BOX CONTENTS
HARDWARE
ASSEMBLY
INSTALLATION
TROUBLESHOOTING TIPS
SAFETY NOTICE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Deltech Fitness DF830 LAT Attachment

Product Information

The DF830 Lat Attachment is an accessory designed for use with a power rack or Smith machine. It allows users to perform lat pulldown exercises and other cable-based exercises. The attachment comes with all the necessary hardware and components for assembly.

Box Contents:

A: Top Frame – Quantity: 1
B: Bottom Support – Quantity: 1
C: Lat Bar – Quantity: 1
D: Low Bar – Quantity: 1
E: Cable – Quantity: 2
F: Weight Carriage – Quantity: 1
G: Rear Support Tube – Quantity: 1
H: Front Support Tube – Quantity: 1
I: Pulley Flange – Quantity: 2
J: 4 Flange – Quantity: 2

Product Usage Instructions

Attach the bottom support (B) to the bottom crossmember of the power rack or Smith machine using M12 x 75MM bolts (O), 4 flange plates (J), M12 washers (U), and M12 locknuts (S). Tighten securely.
Install the rear support tube (G) to the bottom support (B) aligning holes in flange with pin and threaded stud. Install 12mm washer (U) and 12mm nut (S) and tighten. Install the front support tube (H) to the bottom support (B) aligning holes in flange with pin and threaded stud. Install 12mm washer (U) and 12mm nut (S) and tighten.
Install the 4-1/2 pulley (K) into the center flanges of the bottom support using the M10 x 45MM bolt (R), 10mm washers (V), and M10 locknut (T).
Install the 3-1/2 pulley (L) into the front flanges of the bottom support using the M10 x 45MM bolt (R), 10mm washers (V), and M10 locknut (T).
Attach the weight carriage assembly onto the rear frame with the weight bar facing forward. Slide down until it rests on the rubber bumper.
If attaching to DF4900 Smith Machine, use item Y – M12 x 105MM bolts.
Attach the front of the top frame assembly to the power rack with M12 x 75MM bolts (O), M12 washers (U), 4 flange (J), and locknuts (S). If attaching to DF4900 Smith Machine, use M12 x 105MM bolts instead.
Attach the back of the top frame assembly to the frame support tubes with M12 x 65MM bolts (P), M12 washers (U), and locknuts (S). Securely tighten all bolts.
Assemble the floating pulley assembly using the 4-1/2 pulleys (K), the pulley flanges (I), the M10 x 45MM bolts (R), the 10mm flat washers (V), and the 10mm locknuts (T).

Please note that if you encounter any missing hardware or fit up problems during the assembly process, contact Deltech Fitness customer support at 888-258-0533 for assistance.

BOX CONTENTS

HARDWARE

ASSEMBLY

FRAME ASSEMBLY

TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET

ATTACH THE BOTTOM SUPPORT (B) TO THE BOTTOM CROSSMEMBER OF THE POWER RACK OR SMITH MACHINE YOU ARE INSTALLING TO USING M12 x 75MM BOLTS (O), 4” FLANGE PLATES (J), M12 WASHERS (U) AND M12 LOCKNUTS (S). TIGHTEN SECURELY.
INSTALL THE REAR SUPPORT TUBE (G) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM NUT (S) AND TIGHTEN.
INSTALL THE FRONT SUPPORT TUBE (H) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM NUT (S) AND TIGHTEN.
INSTALL THE RUBBER BUMPER ON TO WEIGHT CARRIAGE ASSEMBLY WITH WASHER AND NUT.
INSTALL THE WEIGHT CARRIAGE ASSEMBLY ONTO THE REAR FRAME WITH THE WEIGHT BAR FACING FORWARD. SLIDE DOWN UNTIL IT RESTS ON THE RUBBER BUMPER.
ATTACH THE FRONT OF THE TOP FRAME ASSEMBLY TO THE POWER RACK WITH M12 x 75MM BOLTS (O), M12 WASHERS (U), 4” FLANGE (J), AND LOCKNUTS (S). (IF YOU ARE ATTACHING TO DF4900 SMITH MACHINE USE M12 x 105MM BOLTS INSTEAD)
ATTACH THE BACK OF THE TOP FRAME ASSEMBLY TO THE FRAME SUPPORT TUBES WITH M12 x 65MM BOLTS (P), M12 WASHERS (U), AND LOCKNUTS (S). SECURELY TIGHTEN ALL BOLTS.

LOWER PULLEY ASSEMBLY

INSTALL THE 4-1/2” PULLEY (K) INTO THE CENTER FLANGES OF THE BOTTOM SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCKNUT (T).
INSTALL THE 3-1/2” PULLEY (L) INTO THE FRONT FLANGES OF THE BOTTOM SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCKNUT (T).

FLOATING PULLEY ASSEMBLY

ASSEMBLE THE FLOATING PULLEY ASSEMBLY USING THE 4-1/2” PULLEYS (K), THE PULLEY FLANGES (I), THE M10 x 45MM BOLTS (R), THE 10MM FLAT WASHERS (V), AND THE 10MM LOCKNUTS (T).

INSTALLATION

UPPER CABLE INSTALLATION
THE UPPER AND LOWER CABLES ARE THE SAME.

STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE INTO FRONT OPENING OF THE UPPER PULLEY FRAME AND FEED IT TOWARDS THE BACK. PULL CABLE END OUT THROUGH REAR OPENING.
INSERT 3-1/2” PULLEY (L) INTO FRONT OPENING OF UPPER PULLEY FRAME AND INSTALL USING THE M10 x 70MM BOLT (Q), PULLEY BUSHINGS (M), AND M10 LOCKNUT (T). REPEAT FOR MIDDLE PULLEY.
FEED CABLE END AROUND TOP PULLEY OF FLOATING PULLEY ASSEMBLY AND THEN OVER 3-1/2” PULLEY. INSTALL 3-1/2” PULLEY IN UPPER PULLEY FRAME USING THE M10 x 70MM BOLT (Q), PULLEY BUSHINGS (M), AND M10 LOCKNUT (T).
ATTACH SNAP END OF CABLE AND ATTACH TO FLANGE ON WEIGHT SLIDE.

LOWER CABLE INSTALLATION

STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE UNDER 3-1/2” PULLEY ON FRONT SUPPORT TUBE. MAKE SURE THAT CABLE IS BELOW PULLEY AND ABOVE KEEPER BAR ON BOTTOM OF PULLEY FRAME (SEE INSET PICTURE).
FEED CABLE THROUGH OPENING IN FRONT SUPPORT TUBE. INSTALL CABLE AROUND 4-1/2” LOWER PULLEY, UP AND AROUND BOTTOM PULLEY OF FLOATING PULLEY ASSEMBLY.
ATTACH SNAP HOOKS TO BOTH ENDS OF CHAIN. ATTACH ONE END TO CABLE AND THE OTHER END TO MOUNTING FLANGE ON FRONT SUPPORT TUBE.

LAT BAR INSTALLATION
ATTACH LAT BAR TO UPPER CABLE WITH SNAP HOOK. MOVE TO CRADLE WHEN NOT IN USE.

LOW ROW BAR INSTALLATION
ATTACH LOW ROW BAR TO LOWER CABLE WITH 2 SNAP HOOKS AND CHAIN. YOU CAN ALSO USE THIS CHAIN ON THE HIGH PULLEY TO DO TRICEP EXERCISES.

TROUBLESHOOTING TIPS

CABLE WILL NOT MOVE OR RUBS
- CHECK TO MAKE SURE ALL CABLES ARE IN THE V GROOVE OF THE PULLEYS.
- CHECK ALL PULLEYS TO MAKE SURE THEY ROTATE FREELY.
SEAT OR LEG HOLD-DOWN WON’T ADJUST
- MAKE SURE THE TIGHTEN DOWN KNOB IS LOOSENED BEFORE MAKING ADJUSTMENTS.
MACHINE NOT OPERATING SMOOTHLY
- MAKE SURE BOTH PLASTIC GUIDES ON WEIGHT SLIDE ASSEMBLY ARE FULLY SEATED AND HAVE NOT WORKED LOOSE.
- USE SILICONE SPRAY OR SIMILAR LUBRICANT ON REAR SUPPORT TUBE AND PLASTIC GUIDES ON WEIGHT SLIDE ASSEMBLY.

SAFETY NOTICE

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES:

BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM- PROPER STRETCHING WILL PREPARE YOUR JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
IF AT ANY TIME YOU SHOULD FEEL FAINT, DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER WORK OUT ALONE -ALWAYS HAVE A PARTNER.
SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT LOOSENED.
WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH COULD BECOME ENTANGLED IN MOVING PARTS.
DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND LIABILITIES BECOME VOID.