DELTECH FITNESS DF404 Hyperextension Bench Instruction Manual
- June 12, 2024
- DELTECH FITNESS
Table of Contents
DELTECH FITNESS DF404 Hyperextension Bench
Product Information
| Product Name | DF404 Hyperextension Bench |
|---|---|
| Assembly Manual | Available |
| Assembly Video | Scan the QR code below on your phone’s camera to access the |
video
Contact Information| Toll-Free:
888-258-0533
BOX CONTENTS
HARDWARE
ASSEMBLY
FRAME ASSEMBLY
TOOLS REQUIRED:
ADJUSTABLE WRENCHES OR METRIC SOCKET SET
- ATTACH 1 FOOT (A) TO REAR OF BOTTOM CROSSMEMBER (F) USING TRIANGLE FLANGE (R), M12 x 80MM BOLTS (I), M12 WASHERS (N), AND M12 LOCKNUTS (L).
- ATTACH OTHER FOOT (A) TO FRONT OF BOTTOM CROSSMEMBER (F) USING M12 x 80MM BOLTS (I), M12 WASHERS (N), AND M12 LOCKNUTS (L).
- INSTALL L BRACKETS (Q) TO BOTTOM CROSSMEMBER (F) USING M12 x 80MM BOLTS (I), M12 WASHERS (N), AND M12 LOCKNUTS (L).
- DO NOT TIGHTEN NUTS AT THIS TIME.
- ASSEMBLE THE REAR SUPPORT POST (D) TO THE REAR FOOT USING THE M12 x 80MM BOLTS (I), M12 WASHERS (N)AND M12 LOCKNUTS (L).
- INSTALL FRONT SUPPORT POST (E) TO THE LOWER CROSSMEMBER (F) USING THE M12 x 80MM BOLTS (I), M12 WASHERS (N)AND M12 LOCKNUTS (L).
- DO NOT TIGHTEN NUTS AT THIS TIME.
- ATTACH L BRACKETS (Q) TO FRONT SUPPORT POST (E) USING M12 x 80MM BOLTS (I), M12 WASHERS (N), AND M12 LOCKNUTS (L).
- ATTACH L BRACKETS (Q) TO REAR SUPPORT POST (D) USING M12 x 80MM BOLTS (I), M12 WASHERS (N), AND M12 LOCKNUTS (L).
- DO NOT TIGHTEN NUTS AT THIS TIME.
- ATTACH UPPER CROSSMEMBER (G) USING M12 x 80MM BOLTS (I), M12 WASHERS (N) AND M12 LOCKNUTS (L).
- TIGHTEN ALL NUTS AT THIS TIME.
LEG HOLD DOWN ASSEMBLY
- INSTALL PULL-PIN (U) AND KNOB (P) INTO LEG HOLDDOWN (B).
- INSTALL LEG HOLD DOWN (B) ONTO REAR SUPPORT POST (D). LOCK INTO DESIRED POSITION WITH PULL-PIN AND TIGHTEN KNOB.
FINAL ASSEMBLY
- SLIDE ROLLER PADS (T) ONTO TUBES OF LEG HOLD DOWN (B). INSERT MUSHROOM CAPS (S) INTO ENDS OF TUBES AND HAMMER INTO PLACE WITH RUBBER MALLET.
- INSTALL SEAT FRAME (C) ONTO FRONT SUPPORT POST (E) USING M12 x 65MM CARRIAGE BOLTS (J), M12 WASHERS (N), AND M12 LOCKNUTS (L). TIGHTEN NUTS SECURELY.
SEAT FRAME ASSEMBLY
- INSTALL SEAT PADS (H) TO SEAT FRAME (C) USING M10 x 25 MM BOLTS (Q) AND M10 WASHERS (S).
- INSTALL SEAT PADS (H) TO SEAT FRAME (C) USING M10 x 25 MM BOLTS (Q) AND M10 WASHERS (S).
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE 888-258-0533
Assembly Video Available
Simply scan the QR code below on your phone’s camera to access the video:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>