TE connectivity AXICOM IM Signal Relays Owner’s Manual

: June 12, 2024
: TE connectivity

Table of Contents

INTRODUCTION
FEATURES
APPLICATIONS
CONTACT DATA
PROCESSING
PRODUCT CODE STRUCTURE
PRODUCT SELECTION INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AXICOM IM Signal Relays
Owner’s Manual

INTRODUCTION

TE Connectivity (TE)’s Axicom IM signal relays, as part of our smallest types of electromechanical relays, offer a wide and deep range of variations suitable for many applications.
The IM series are equipped with 2 changeover contacts in both monostable or bistable versions, available in multiple coil solutions, performance types and pin layouts.

FEATURES

Slim line 10x6mm, low profile 5.65mm and min. board-space 60mm².
Switching current 2/5A, switching power 60W/62.5VA and switching voltage 220VDC/250VAC.
Low coil power consumption, 140mW standard, 100mW for high sensitive version, 50mW for ultra high sensitive version and 100mW for bistable version.
High dielectric and surge capability up to 2500Vrms between open contacts and 2500Vrms between coil and contacts.
High mechanical shock resistance up to 50g functional.

APPLICATIONS

Telecommunication
Access and transmission equipment
Optical network terminals
Modems
Office and business equipment
Consumer electronics
Measurement and test equipment
Industrial control
Medical equipment
HVAC

APPROVALS

UL 61810-1 (former UL 508) File No. E214025

Technical data of approved types on request
Buyer entirely assumes the risk and all liability relating to (a) assessing the suitability for Buyer’s intended use of the Products and of any system design or drawing and (b) determining the compliance of Buyer’s use of the Products with applicable laws, regulations, codes and standards. For more info on the exclusive and applicable warranty, please refer to TE standard warranty terms.

CONTACT DATA

Performance type| Standard, C (Standard and high dielectric
version)| D, I (High current version)| P (High contact stability version)
---|---|---|---
Contact arrangement| 2 form C, 2 CO
Max. switching voltage| 220VDC,
250VAC| 220VDC,
250VAC| 220VDC,
250VAC
Rated current| 2A| 5A
1)| 2A
Limiting continuous
current| 2A| 5A
1)| 2A
Switching power| 60W, 62.5VA
Contact material| PdRu +Au
covered| AgNi +Au
covered| PdRu +Au
covered
Contact style| Twin contacts| Twin contacts
I: single
contacts| Twin contacts
Minimum switching
voltage| 100μV
Initial contact resistance| <50mΩ at 10mA/30mV
I: < 100mΩ
Thermoelectric potential| <10μV
Operate time| typ. 1ms, max. 3ms
Release time|
Without diode
in parallel| typ. 1ms, max. 3ms
With diode in parallel| typ. 3ms, max. 5ms
Bounce time max.| typ. 1ms, max. 5ms
Electrical endurance|
at contact application
0 (≤30mV/≤10mA)| min. 2.5×106 operations
Cable load open end| min. 2.0×106 operations
Resistive, 125VDC
/ 0.24A – 30W| min. 5×105 operations
Resistive, 220 VDC
/ 0.27A – 60W| min. 1×105 operations
Resistive, 250VAC
/ 0.25A – 62.5VA| min. 1×105 operations
Resistive, 30VDC
/ 1A – 30W| min. 5×105 operations
Resistive, 30VDC
/ 2A – 60W| min. 1×105 operations
UL contact
rating| 30VDC, 2A, 60W, NO only
110VDC, 0.3A, 33W
220VDC, 0.27A, 60W
125VAC, 0.5A, 62.5VA
250VAC, 0.25A, 62.5VA
30VAC, 2A, 62.5VA, NO only (IMxxI, IMxxD)
---|---
Mechanical
endurance| min. 1×108 operations

MAX. DC LOAD BREAKING CAPACITY

TE connectivity AXICOM IM Signal Relays - BREAKING

COIL DATA

Magnetic system	Monostable, bistable
Coil voltage range	1.5 to 24VDC
Coil code	Rated voltage VDC
voltage VDC**	Coil resistance Ω±10%
---	---

Coil versions, standard version, monostable, 1 coil
0| 1.5| 1.13| 0.15| 16| 140
8| 2.4| 1.8| 0.24| 41| 140
1| 3| 2.25| 0.3| 64| 140
2| 4.5| 3.38| 0.45| 145| 140
3| 5| 3.75| 0.5| 178| 140
4| 6| 4.5| 0.6| 257| 140
5| 9| 6.75| 0.9| 579| 140
6| 12| 9| 1.2| 1029| 140
7| 24| 18| 2.4| 2880| 200
Coil versions, sensitive version, monostable, 1 coil
11| 3| 2.4| 0.3| 91| 100
12| 4.5| 3.6| 0.45| 194| 100
13| 5| 4| 0.5| 234| 100
16| 12| 9.6| 1.2| 1315| 110
17| 24| 19.2| 2.4| 4120| 140
Coil versions, ultra high sensitive version, monostable, 1 coil
21| 3| 3| 0.3| 180| 50
22| 4.5| 4.5| 0.45| 405| 50
23| 5| 5| 0.5| 500| 50
26| 12| 12| 1.2| 2880| 50

All figures are given for coil without pre-energization, at ambient temperature +23°C

Coil code| Rated voltage VDC| Operate voltage VDC| Release voltage VDC| Coil resistance Ω±10%| Rated coil power mW
---|---|---|---|---|---
Coil versions, standard version, bistable 1 coil
40| 1.5| 1.13| -1.13| 16| 100
48| 2.4| 1.8| -1.8| 41| 100
41| 3| 2.25| -2.25| 64| 100
42| 4.5| 3.38| -3.38| 145| 100
43| 5| 3.75| -3.75| 178| 100
44| 6| 4.5| -4.5| 257| 100
45| 9| 6.75| -6.75| 579| 100
46| 12| 9| -9| 1029| 100
47| 24| 18| 18| 2880| 200

COIL OPERATING RANGE,
STANDARD VERSION, MONOSTABLE, 1 COIL
TE connectivity AXICOM IM Signal Relays - range
COIL OPERATING RANGE,
SENSITIVE AND ULTRA HIGH SENSITIVE VERSION,
MONOSTABLE, 1 COIL
COIL OPERATING RANGE,
STANDARD VERSION, BISTABLE, 1 COIL

TE connectivity AXICOM IM Signal Relays - STANDARD

INSULATION DATA

Performance type| Standard (Standard, sensitive, ultra high sensitive version)| C 2)
(High dielectric version)| D, P, I
(High current, high contact stability
version)
---|---|---|---
Initial dielectric strength
between open
contacts| 750Vrms| 1500Vrms| 750Vrms
between contact
and coil| 1800Vrms| 1800Vrms| 1500Vrms
between adjacent
contacts| 1000Vrms| 1800Vrms| 750Vrms
Initial surge withstand voltage
between open
contacts| 1500V| 2500V| 1000V
between contact
and coil| 2500V| 2500V| 2000V
between adjacent
contacts| 1500V| 2500V| 1000V
Initial insulation resistance
between insulated
elements| >10⁹Ω| >10⁹Ω| >10⁹Ω
Capacitance
between open
contacts| max. 1pF
between contact
and coil| max. 2pF
between adjacent
contacts| max. 2pF

this relay contains SF6 (Sulfur hexafluoride, CAS number: 2551-62-4) for dielectric strength enhancement, SF6 is hermetically sealed in relay without leaks to air during normal application as recommended per the applicable product specification. It is clarified that the usage of SF6 in mini signal relay is not prohibited by related regulations. Please contact TE local sales or field engineer for further information and detailed material declaration. To ensure the dielectric performance after soldering processes / assembly customer is advised to perform a dielectric test.

RF DATA

Isolation at 100MHz/900MHz	37.0dB/18.8dB
Insertion loss at 100MHz/900MHz	0.03dB/0.33dB
Voltage standing wave ratio (VSWR) at 100MHz/900MHz	1.06/1.49

OTHER DATA

Material compliance| EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at

www.te.com/customersupport/ rohssupportcenter

---|---
Ambient temperature| -40°C to +85°C
Thermal resistance| <150K/W
Category of environmental protection IEC 61810|

RT V – hermetically sealed

Vibration resistance (functional)| 20g, 10 to 500Hz
Shock resistance (functional), half sinus 11ms| 50g
Shock resistance (destructive), half sinus 0.5ms| 500g
Mounting position| various
Weight| max. 0.75g
Resistance to soldering heat SMT IEC 60068-2-58| Moisture sensitive level, JEDEC J-STD-020F MSL3 related only to SMT relays packed in orginal dry-packs. Calculated shelf life in sealed bag: 36 months at <400C and <90% relative humidity (RH). Floor life (out of the bag) at assembly site is 168 Hours at £

300C/60% RH.

MONOSTABLE VERSION REST CONDITION

ching Type, 1 Coil RESET CONDITION
Contacts are shown in reset condition.
Contact position might change during transportation and must be reset before use.

DIMENSIONS

(UNIT: mm)

TE connectivity AXICOM IM Signal Relays - DIMENSIONS

PCB LAYOUT

Top view on component side of PCB

TE connectivity AXICOM IM Signal Relays - PCB LAYOUT

PROCESSING

Recommended soldering conditions
Recommended reflow soldering profile IEC 61760-1

TE connectivity AXICOM IM Signal Relays - PROCESSING PACKING
Tube for THT version
50 relays per tube, 1000 relays per box

TE connectivity AXICOM IM Signal Relays - PACKING Recommended vapor phase soldering profile

TE connectivity AXICOM IM Signal Relays - Reel
dimensions3

Tape and reel for SMT version
1000 relays per reel, 1000 or 5000 relays per box

TE connectivity AXICOM IM Signal Relays - SMT Reel dimensions Note:
The author thanks the International Electrotechnical Commission (IEC) for permission to reproduce Information from its International Standards. All such extracts are copyright of IEC, Geneva, Switzerland. All rights reserved. Further information on the IEC is available from www.iec.ch. IEC has no responsibility for the placement and context in which the extracts and contents are reproduced by the author, nor is IEC in any way responsible for the other content or accuracy therein.”

PRODUCT CODE STRUCTURE

TE connectivity AXICOM IM Signal Relays - Reel
dimensions2

PRODUCT SELECTION INFORMATION

Product code| Arrangement| Perf. type| Coil| Coil type| Coil| Terminals| Part number
---|---|---|---|---|---|---|---
IM00GR| ****

2 form C, 2 CO contacts

| ****

Standard

| 1.5VDC|

**** Monostable

2 form C,

2 CO

contacts

| Standard| **** 5VDC| Monostable|

Standard

| SMT gull wing| 1-1462037-4
---|---|---|---|---|---|---|---
IM03SR| SMT short gull wing| 2-1462040-5
IM03JR| SMT J-leg| 1-1462037-6
IM03NS| THT narrow| 1-1462038-3
IM03TS| THT standard| 1-1462037-8
IM04GR| 6VDC| SMT gull wing| 4-1462037-2
IM04JR| SMT J-leg| 4-1462037-4
IM04NS| THT narrow| 1-1462038-4
IM05GR| 9VDC| SMT gull wing| 3-1462037-4
IM05SR| SMT short gull wing| 2-1462040-6
IM05JR| SMT J-leg| 4-1462037-5
IM05NS| THT narrow| 1-1462038-5
IM05TS| THT standard| 2-1462037-2
IM06GR| 12VDC| SMT gull wing| 2-1462037-3
IM06SR| SMT short gull wing| 2-1462040-7
IM06JR| SMT J-leg| 4-1462037-6
IM06NS| THT narrow| 1-1462038-6
IM07GR| 24VDC| SMT gull wing| 4-1462037-7
IM07SR| SMT short gull wing| 2-1462040-8
IM07JR| SMT J-leg| 4-1462037-8
IM07NS| THT narrow| 1-1462038-7
IM08GR| 2.4VDC| SMT gull wing| 6-1462039-3
IM11GR| 3VDC| High sens.| 9-1462038-5
IM12GR| 4.5VDC| 1462039-3
IM13GR| 5VDC| 1462039-4
IM16GR| 12VDC| 1462039-5
IM17GR| 24VDC| 1462039-6
IM17TS| THT standard| 4-1462039-6
IM21GR| 3VDC| ****

Ultra high sensitive

12VDC

| SMT gull wing| 3-1462039-1
IM26TS| THT standard| 3-1462039-2
Product code| Arrangement| Perf. type| Coil| Coil type| Coil| Terminals| Part number
---|---|---|---|---|---|---|---
3) IM40GR| ****

**** 2 form C, 2 CO contacts

| ****

Standard

| ****

1.5VDC

3VDC

4.5VDC

5VDC

9VDC

2.4VDC

| SMT gull wing| 1462039-8
3) IM48SR| SMT short gull wing| 3-1462040-6
Product code| Arrangement| Perf. type| Coil| Coil type| Coil| Terminals| Part number
---|---|---|---|---|---|---|---
IM01CGR|

2 form C, 2 CO contacts

|

High dielectric

| 3VDC|

Monostable

|

Standard

5VDC

12VDC

24VDC

Standard

| 4-1462039-2
3) IM42CGR| 4.5VDC| 4-1462039-1
3) IM43CGR| 5VDC| 9-1462038-7
3) IM48CGR| 2.4VDC| 9-1462039-0
IM02DGR| |

High current

| 4.5VDC|

Monostable

|

Standard

SMT gull wing

THT standard

Bistable

|

Standard

|

SMT gull wing

THT narrow

| 1-1462039-6
IM46DNS| 12VDC| 1-1462039-2
IM47DJR| 24VDC| SMT J-leg| 7-1462039-5
IM48DGR| 2.4VDC|

SMT gull wing

| 1462039-9
IM49DGR| 2VDC| 2-1462039-2
IM40IGR| 1.5VDC| 1462047-7
IM48IGR| 2.4VDC| 1462047-1
IM49IGR| 2VDC| 1462047-4
Product code| Arrangement| Perf. type| Coil| Coil type| Coil| Terminals| Part number
---|---|---|---|---|---|---|---
IM02PGR| |

High contact stability

|

4.5VDC

|

Monostable

12VDC

4.5VDC

|

Bistable

Type VDE certified, for more information contact TE
Note:
This list represents the most common types and does not show all variants covered by this datasheet. Other types on request.

Notes:

Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions.
Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change.

te.com

©2023 TE Connectivity Ltd. Family of Companies. All Rights Reserved.
Axicom, TE Connectivity, TE connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners.
While TE has made every reasonable effort to ensure the accuracy of the information in this document, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any changes to the information contained herein without prior notice. TE Connectivity assumes only those obligations set forth in the terms and conditions for this product and shall in no event be liable for any ncidental, indirect, or consequential damages arising out of the sale, resale, use, or misapplication of the product. TE expressly disclaims any implied warranties with respect to the information contained herein, including, but not limited to, implied warranties of merchantability or fitness for a particular purpose. Dimensions, specifications and/or information contained herein are for reference purposes only and are subject to change without notice. Consult TE for the latest dimensions, specifications and/or nformation. Users of TE Connectivity products must make their own assessment as to whether the respective product is suitable for the respective desired application.