Chacon 34048 Alarm with Motion Detector and Integrated Keypad Instruction Manual
- June 3, 2024
- CHACON
Table of Contents
Chacon 34048 Alarm with Motion Detector and Integrated Keypad
Alarm with motion detector and integrated keypad
registering the guarantee
To register your warranty, fill in the online form at
www.chacon.com/warranty
Product Overview
Introduction
Thank you for using this product.
- Please read all instructions carefully before using the product.
- Do not attempt to disassemble or repair the product yourself, as this will invalidate the warranty.
- This product is compatible with these references: 34035, 34036, 34038, 34043, 34044, 34045, 34046)
Battery installation: Central alarm unit with motion detector
- Using a crosshead screwdriver, remove the screw from the back of the opening detector.
- Slide the cover down to access the battery compartment.
- Insert the batteries, ensuring correct polarity (+/-).
- Close the compartment with the cover and screw.
Note: When the battery is low, the LED indicator will flash slowly (3s/flash)
Installing the alarm unit
Once the batteries have been installed, choose the location where you wish to place your opening detector. There are two methods:
- Fix the bracket to the wall using the dowels and screws provided and then fit the detector onto the bracket, ensuring the best possible range.
- Recommended installation height: Maximum 160cm and minimum 30cm. NOTE: Adjust the installation angle so that it faces downwards.
- Simply place it on a table or desk for easy access to the keypad.
- Setting up the personal code Once you have placed your batteries, you have 15 seconds to choose a four-digit code. If you have not had time to enter your personal code, the code 1234 will be saved by default.
- Keypad functionality Home Mode: Enter your 4-digit code, then press the «1» button. You will hear a «beep» to indicate that the alarm will enter «home» mode after 30 seconds.
- NOTE: In this case, the motion detection function is disabled. Only the magnetic door sensor will trigger an alarm.
- Away mode: Enter your 4-digit code, then press the «2» button. You will hear a «beep» to indicate that the alarm will enter the «Away» mode after 30 seconds.
- NOTE: In this case, if someone opens the door or window equipped with the opening detector or enters the field of vision of your motion detector, the alarm will be triggered.
- Emergency mode: Press buttons 1 and 4 simultaneously in an emergency. An alarm will sound without a time limit to scare off intruders.
Combining your alarm unit with other accessories
- Using a screwdriver, open the battery compartment of the main unit.
- Press and hold the learn button until you hear a «beep». The unit enters pairing mode. (see diagram point 1)
- Remote control: Press any button on the remote control. You will hear a «beep» sound to indicate that the pairing was successful.
- Opening detector with or without code: Separate the two parts of the opening sensor to send a signal to the main unit. You will hear a «beep» indicating successful coupling.
- Motion detector: Wave your hand in front of the motion detector. You will hear a «beep» indicating a successful pairing.
- Remote keypad: Press any button on the remote keypad. You will hear a «beep» indicating a successful pairing.
- To exit pairing mode, press and hold the learn button for 3 seconds. You will hear a double «beep»
Reset pairing
In order to reset your entire alarm, remove the batteries from your device. Then press and hold the learning button of your central unit (see diagram point.1). When you reinsert the batteries, you will hear two «beeps» indicating that the reset was successful.
A 100% compatible ecosystem
We have created a 100% compatible alarm system to meet your needs. Here, we
offer accessories that can work alone but also as a kit. This allows you to
personalize your alarm and to associate several accessories but also several
alarms between them. For example, when a person triggers the opening detector,
all your alarms will sound. You can deactivate your alarm using the code
units, remote control or the remote keyboard. More information on our website:
https://chacon.com/fr/
Compatible products: 34035, 34036, 34038, 34043, 34044, 34045, 34046
Problem-solving
- Check that there are no animals near the motion detector.
- In hot weather, moving shadows may also activate the alarm. Also, ensure that the detector is not installed near a radiator or heat source.
- Check that there are no devices with strong electromagnetic fields near the door/window sensor. Strong electromagnetic fields can cause false alarms.
- Check if the pairing between the transmitter and the main unit was successful.
- If the pairing was successful, check the battery voltage of the main unit and transmitter. Low voltage will result in product failure.
- Check if the low battery indicator is flashing (please replace the batteries immediately).
- If the unit is armed and set to HOME mode and the PIR sensor detects an intrusion, the alarm will not sound. The PIR sensor is disabled in HOME mode. Check if the main unit is installed correctly.
Safety advice
- Don’t mix new and used batteries.
- Don’t mix alkaline, standard (zinc-carbon) or rechargeable (ni-cad, ni-me, etc.) batteries.
- Please use only the type of battery specified in the manual.
- Don’t leave used batteries lying around in the unit, as this may damage the unit.
- Incorrect use of the battery may damage nearby objects and result in fire or serious injury.
- Please keep batteries away from children. If you suspect that batteries have been ingested, seek medical attention immediately. Swallowing the battery can lead to serious consequences; internal burns within 2 hours or death.
- Recycle used batteries in accordance with environmental protection practices
- Don’t place the unit near a heat source, where it may be exposed to direct sunlight, rain or strong light.
- The unit is not waterproof. Don’t expose it to rain or immerse it in water.
- Don’t attempt to disassemble or repair the product yourself.
- Please keep this manual in a safe place.
- The reception distance may be affected if a strong interference signal exists in the area of use.
Technical specifications
- Easy to install
- Can be switched on or off via the keypad on the unit
- Compatible products: 34035, 34036, 34038, 34043, 34044, 34045, 34046
- Alarm time: 30s
- Detection distance: 8m
- Detection angle: 100°
- Alarm volume: 100 dB
- Standby current: ≤ 350uA
- Alarm current: ≤ 150mA
- Battery: 3x AAA 1.5V (not included)
- Box contents: Alarm with motion detector and integrated code + fixing material + manual
For indoor use, only This product must be treated in accordance with European Directive 2002/96/EC with the aim of being recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities. Hereby, Chacon declares that the radio equipment type 34048 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.chacon.com/conformity
Chacon S.A. – Avenue Mercator 2 – 1300 Wavre – Belgium Made in PRC