FERIETELF T6 2.4GHz 6ch Remote Control Quadcopter Drone Camera Instructions
- June 14, 2024
- FERIETELF
Table of Contents
- T6 2.4GHz 6ch Remote Control Quadcopter Drone Camera
- Product packaging contents
- Part identification
- Battery installation and charging
- Install the blade 、protective cover
- Aircraft calibration
- Automatic setting height
- Take-off
- One key take-off / One key landing
- Aircraft operation and control
- Sensitivity setting
- Flip mode
- Camera (Optional)
- Compass (Headless) mode
- One key return mode
- Fault removal
- List of accessories
- Documents / Resources
Suitable for children
over 14 years old
2.4GHz 6CH REMOTE CONTROL
QUADCOPTER
INSTRUCTIONS
T6 2.4GHz 6ch Remote Control Quadcopter Drone Camera
SECURITY WARNING:
- This product is a high-speed aircraft. improper use may cause damage to people or property in the vicinity, so the users must be away from people or property during use. In the case of accidental damage, the manufacturer and its distributors and retailers will not be liable for any legal liability.
- To ensure safety of you and your children, please read this manual while playing this Aircraft.
- Do not pick up the aircraft in motion to avoid injuries.
- Keep hands, hair and loose clothes away from rotary propeller.
- To ensure safety of children, adults please accompany children whiling playing this aircraft (Without authorization, free change or modification of this product will damage your rights related to this product.)
Product packaging contents
Part identification
Aircraft
Remote Control
1| Photo/Video (Optional)| Click once to shoot one picture by the camera on
the aircraft. After that, the camera will quit automatically.
Press the key for 2 seconds, the camera on the aircraft will shoot a video.
Please it again from 2 seconds to quit. (the camera is an optional part).
---|---|---
2| Power switch| Control power switch, turn right to plug in, turn left to
disconnect power.
3| Left joystick| Stir the joystick forward or backward to control rise and
fall, stir the joystick left or right to control left and right rotation.
4| One key take-off| After starting the aircraft, every time it is clicked, it
automatically rises by about 1.5 m.
5| Acceleration| One click to raise a gear (default low speed mode).
6| Deceleration| One click to reduce a gear (default low speed mode).
7| One key landing| During flight, click once for automatic landing.
8| One button back| Click once to enter into the “One button back” mode
9| Power light| Displays the battery level of the remote controller and
prompts for various functions. (The slow flashes of the power indicator means
that the battery of the remote control is dead and needs to be replaced)
10| Flip/ Compass| Click once to enter to the flip mode before automatic
cancel. Press the key for 2 seconds to enter to the compass mode, and press it
again for 2 seconds to quit.
11| Right joystick| Stir the joystick forward or backward to control the
aircraft to move forward or backward, stir the joystick left or right to
control the aircraft to fly at left or right directions.
12| Forward fine-tuning| Assist in adjusting the aircraft to move forward .
13| Right flying fine-tuning| Assist in adjusting the aircraft to fly at left
directions.
14| Emergency stop| Press and hold emergency stop for 2 seconds, the aircraft
will stop urgently.
15| Backward fine-tuning| Assist in adjusting the aircraft to move backward.
16| Lighting control| Click “light control” to control the navigation light of
Aircraft ( default: ON).
17| Left flying fine-tuning| Assist in adjusting the aircraft to fly at
directions.
Battery installation and charging
- Remove the battery cover.
- Install 3 “AA” batteries, according to the correct polarity.
- Close the battery cover.
Battery installation of Aircraft
- Put the battery into the body.
- Push the battery forward to grip the body.
Lithium Battery Charging
Remove the battery from the aircraft, and then plug the USB cable into the USB
port of the computer or other USB charger. The indicator light will be off.
Connect the plug of the battery with the socket on the USB charging cable. The
indicator light is on, indicating that it is charging; the indicator light is
off, indicating that it is fully charged.
Note: The USB charging line can be connected to most smartphone chargers
or mobile power sources or USB interface in automobiles.
The voltage in USB interface is 5V±0.5V. (The current cannot be> 1A)
Note: If the light of the aircraft flashes slowly and the buzzer of the remote controller emits a “beep” sound simultaneously, it means that the aircraft is running out of power and needs to fly back to charge.
Install the blade 、protective cover
The blade of the aircraft is not the same for every piece. Each blade is marked with “A” or “B”. When install the blade, please correctly install according to the corresponding tag as shown below. When the blade is not properly installed, the aircraft will be unable to take off,or rollover or throw.
- Install the blades as shown in the illustration and lock it with 1 screw.
- Install the protective cover as shown in the illustration.
First remove the protective cover and then install the protective cover.
Aircraft calibration
After matching the code between the aircraft and remote control, put the
aircraft on a horizontal plane, and push the “left joystick” and “right
joystick” on the remote control until the navigation light flashes, as shown
below. After the calibration is completed, the navigation light will return to
normal. (When the aircraft is offset in any direction and fine-tuning cannot
be adjusted, this calibration can be used for repair.)
Automatic setting height
- This aircraft adopts “barometer” module to achieve fixed height and hovering; use the left joystick (accelerator) to control rise/fall; loosen the left joystick (accelerator), the aircraft will hover at that height.
Take-off
- Put a fully charged battery into the aircraft and press and hold the aircraft power switch for about 2 seconds to start the aircraft. Then place the aircraft on level ground with the nose on the front. (At this time, the aircraft light will flash.)
- Turn off switch of the remote control (the power indicator is on) push left lever to top and then to end, Aircraft and remote control begin to match codes, after that, power indicator of remote control and light of PRV will be always on.
Start /Close the aircraft (choose the “set height” function)
To start the drone:
Move the left lever (throttle lever) to the top, the aircraft blades will
slowly rotate.To close the drone:
- Dial the left joystick (throttle) to the bottom until the aircraft blades stop rotating.
- After the aircraft lands on the ground, press the ( STOP ) button for 2 seconds to turn off the aircraft. ( Emergency stop function cannot be used unless the aircraft needs to be urgently stopped when it is on the ground or in special circumstances.)
One key take-off / One key landing
One key take-off
- After starting the aircraft, click “One key take-off” ( ) button, the aircraft will rise to about 1.5m automatically. [No use of left joystick (accelerator)]
One key landing
- Click “One key landing” ( ) button, the aircraft will land on the ground slowly from any heights. [No use of left joystick (accelerator)]
Aircraft operation and control
Caution: To avoid losing control, move the joystick slowly while operating the aircraft.
Fine tuning
If Aircraft deviates the direction (left/right turning, forward/backward,
left/right side flight) , push finetuning key in an opposite direction. For
example, as shown in the figure, push back when deviating forward.
Sensitivity setting
This aircraft can be operated in 3 modes: low speed – medium speed – high speed Press the “Acceleration” button to adjust to a higher gear, press the “Deceleration” button to adjust to a lower gear (when turning on the aircraft, the default setting is low speed):
- After pressing the button, when the remote control buzzer beeps once, it means the aircraft is in the low speed mode
- After pressing the button, when the remote control buzzer beeps twice, it means the aircraft is in the medium speed mode
- After pressing the button, when the remote control buzzer beeps three times, it means the aircraft is in the high speed mode
Adjust sensitivity of Aircraft by this key,if the sensitivity is higher, Aircraft responds more quickly, otherwise, more slowly.
Flip mode
This Aircraft can roll 360 degrees by the following operations. To better
perform rolling function and ensure the Aircraft is 4 meters away from the
ground, it is necessary to roll in the rising process. Thus, the height is
more easily maintained after rolling.
Flip
Left flip Click “flip/compass” ( ) key, push left the right lever, and then push the lever into center.
Front flip
Click “flip/compass” ( ) key, push front the
right lever,and then push the lever into center .
Right flip
Click “flip/compass” ( ) key, push right the right lever, and then push the lever into center.
Back flip Click “flip/compass” ( ) key, push back the right lever, and then push the lever into center.
Camera (Optional)
-
Turn on the power of the aircraft, turn on the remote controller of the aircraft and match the code.
-
Scan (optional) the QR code of the instruction manual to download the APP, connect to WiFi according to the instructions, and open the real-time transmission interface on APP.
-
The camera on the aircraft will take a photo by clicking the “Photo/Video” ( ) button, and it will exit automatically after taking the photo.
-
The camera on the aircraft will shoot a video by pressing the “Photo/Video” ( ) button for 2 seconds, and it will exit the Video mode by pressing the “Photo/Video” ( ) button for 2 seconds.
-
Ensure operation according to above steps.
-
When taking pictures, the time interval shall not be less han 2 seconds.
Compass (Headless) mode
-
What is “Flip/Compass (Headless) mode”?
Namely, during flying, no matter where the PRV is, and no matter what its direction is, as long as the operator press “Flip/Compass” ( ) key, PRV will automatically lock the flying direction -
When will the operator use the “Compass (Headless) mode”?
When the Aircraft is far from you and you cannot know its direction, you can press “Flip/Compass” ( ) key to control the return of Aircraft. -
Use of “Flip/Compass (Headless) mode”
- When matching code, the head of Aircraft shall be in front (otherwise, the direction will be mixed when opening the “Flip/Compass” mode).
- To better use “Flip/Compass” mode, before flying, it is necessary to establish a direction coordinate on the ground. .
- When you need to use compass mode, press “Flip/Compass”( ) key, and the Aircraft will automati cally lock flying direction.
- When you do not need to use “Flip/Compass” mode, press “Flip/Compass” ( ) key for 2 seconds to exit.
One key return mode
- When you find that the aircraft is far away from you in flight, and you can’t tell its direction clearly, you can click the “One button back” ( ) button, and control the height of the aircraft by the left control stick (do not operate the right control stick), in which case the aircraft will automatically go backward.
- When the aircraft automatically return to the visual range, you may toggle the right control stick in the forward and backward direction or click the “One button back” ( ) button again to exit the “One button back” mode.
When clicking the “One button back” button, the aircraft will go back following the direction of the aircraft when operating the right code
Fault removal
-
Remote control and Aircraft cannot match codes.
Solutions: Check whether the throttle of remote control is lowest; when starting code match, do not push other levers or click fine-tuning key -
Propeller does not rotate or responds slowly.
Solutions: (1 ) Lithium battery power is low. (2) You need to re-match codes. (3) push throttle to bottom to make Aircraft land, and fly again after 3 seconds. -
Aircraft shakes or vibrates during flying, noise is loud. Check whether motor, housing or blade is installed correctly or whether the cone is damaged.
-
The blade can rotate but Aircraft cannot fly.
Solutions: Check whether A/B blades are installed correctly. -
One or more motors cannot work.
Solutions:
(1) The motor is broken, change it.
(2) The motor line falls off, to heavy welding lines.
(3) A transistor on the launch panel of remote control is burned out, replace it with a new remote control.
-
Four axles still drift during suspension after recalibration.
Solutions: Put Aircraft on a flat ground and put several layers of paper on its directing direction (the thickness of the paper depends on the degree of drift). Thus, you can calibrate the accelerometer and solve drifting problem. -
Can not roll
Solutions: Low battery needs charging.
List of accessories
MADE IN CHINA
Documents / Resources
|
FERIETELF T6 2.4GHz 6ch Remote Control Quadcopter Drone
Camera
[pdf] Instructions
C1HzVdGe09L, T6, T6 2.4GHz 6ch Remote Control Quadcopter Drone Camera, 2.4GHz
6ch Remote Control Quadcopter Drone Camera, 6ch Remote Control Quadcopter
Drone Camera, Remote Control Quadcopter Drone Camera, Control Quadcopter Drone
Camera, Quadcopter Drone Camera, Drone Camera, Camera
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>