CDVI V3SR 300 Kg Surface Mount Electromagnetic Lock Instruction Manual
- June 12, 2024
- CDVI
Table of Contents
CDVI V3SR 300 Kg Surface Mount Electromagnetic Lock
Product Information:
- Product Name: V3SR
- Product Type: Surface Mount Electromagnetic Lock
- Intended Use: General use (not for fire safety)
- Product Features:
- Monitored
- High Corrosion resistance
- Safety Rope Delivered with armature
- No mechanical wear
- Ease of installation
- Recommended for interior use
- Fail safe (Door unlocked when power off)
- Holding force: 300 kg
- No residual magnetism
- Visual signalling (Blue = Locked ; Green = Open)
- Built-in varistor: Built-in electronic protection to eliminate back EMF
- Dimensions (L x W x D): 254 x 45 x 27mm
- Armature dimensions (L x W x D): 185 x 38 x 11mm
- Power supply: 12/24V dc
- Power absorption: 12 V DC = 480mA, 24 V DC = 240mA
- WEEE & RoHS EC certification IP42
- Package Contents: Fixing plate, Security rope, M8 screw, Roll pin, Armature plate, Cap nut, Steel washer, Rubber washer, Mounting screws, Manual
- Warranty: 10 years
Product Usage Instructions
- Installation:
- Fix the electromagnetic lock and armature plate solidly on their supports.
- Ensure that the magnet and the armature meet evenly over their entire mating surfaces.
- The armature plate must be able to pivot slightly about its center mounting screw to compensate for any door misalignment.
- Secure the security rope to both the magnetic lock and the frame using the provided fixing points.
- Electrical Connections:
- Check the voltage selection jumpers and set them accordingly to the desired power supply (12V dc or 24V dc).
- Connect the terminals of the electromagnetic lock to the corresponding terminals of the power supply: NO (Normally open), COM (Common), NC (Normally closed).
- The N.O./N.C. signal only switches when the door is closed and the electromagnetic lock is powered.
- Make sure to check the jumper position before connecting the lock to the input current to avoid damaging the lock.
- Mounting Recommendations:
- Use the provided mounting accessories (fixing plate, roll pin, screws, washers) to securely mount the magnetic lock and armature plate.
- Install both security ropes supplied to prevent the risk of the electromagnetic lock from falling and ensure the safety of users.
- Recommended Power Supplies: ADC335, ADC612SB
Note: All the information contained within this document (photos, drawing, features, specifications, and dimensions) could be perceptibly different and can be changed without prior notice.
300 Kg Surface Mount Electromagnetic lock
(For general use – not fi re safety use)
PRODUCT PRESENTATION
- Monitored
- Surface mount
- High Corrosion resistance
- Safety Rope
- Delivered with armature
- No mechanical wear
- Ease of installation
- Recommended for interior use
- Fail safe (Door unlocked when power off)
- Holding force: 300 kg
- No residual magnetism
- Visual signalling (Blue = Locked ; Green = Open)
- Built-in varistor: Built-in electronic protection to eliminate back EMF
- Dimensions (L x W x D): 254 x 45 x 27mm
- Armature dimensions (L x W x D): 185 x 38 x 11mm
- Power supply: 12/24V dc
- Power absorption: 12 V DC = 480mA 24 V DC = 240mA
The V3SR is suitable for the new regulations covering assistance to persons with reduced mobility.
PACKAGE CONTENTS
ELECTRICAL CONNECTIONS
12V dc default setup
| Terminal block | Correspondence |
|---|---|
| + | 12 or 24V dc |
| – | – 0 V |
| NO | Normally open |
| C | COM |
| NC | Normally closed |
The N.O./N.C. signal only switches when the door is closed and electromagnetic lock powered.
IMPORTANT NOTE
Check the jumper position before connecting the lock to the input current. A
wrong position could damage the lock. This type of damage is not covered by
the warranty.
Voltage selection jumpers
Recommended power supplies
INSTALLATION
MOUNTING RECOMMENDATIONS
Armature plate
- It is vital to fi x the electromagnetic lock and armature plate solidly on their supports.
- Make sure that the magnet and the armature meet evenly over their entire mating surfaces.
- The armature plate must be able to pivot slightly about its center mounting screw to compensate for any door misalignment.
Security ropes
The electromagnetic lock undergoes repeated shocks and the vibration at the
points of fi xation on the frame (frequencies of openings / closures, attempt
of opening wears closed and attempts of vandalism) which can loosen the fi
xing bolts/ screws.
To prevent the risk of the electromagnetic block from falling, install both
security ropes supplied, to guarantee the safety of the users (see plan
above).
G0301FR1024V03
All the information contained within this document (photos, drawing, features,
specifi cations and dimensions) could be perceptibly different and can be
changed without prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>