CDVI RX CUBE POWER Bluetooth Controlled Radio Receiver Instruction Manual

: June 9, 2024
: CDVI

CDVI RX CUBE POWER Bluetooth Controlled Radio Receiver Instruction Manual

Introduction

RX CUBE POWER – Bluetooth controlled radio receiver
The receiver ERONE “Cube Power” is a super heterodyne radio receiver operating at 433,92 MHz in AM/ASK demodulation.
It is compatible with the full range of remote controls Erone that use the Keeloq® Hopping code security protocol.
This receiver can be programmed only via Bluetooth using set-up and control that can be done only using the app : “RX Cube” on a Smartphone ( iOS or Android ).
Power supply 12-24 Vac/dc autodetect. High power output contacts The equipment is manufactured in compliance with the provisions of European Directive 2014/30/EU, 2014/35/EU, 2014/53/EU and the provisions of the standard EN 62368-1.

Part-name	F-code	Description
SEL2641R433-RCP	F1001000106	RECEIVER CUBE POWER 12/24V

Overview

Technical Specifications

Receiver type: Super heterodyne
Operating frequency: 433,92 MHz – AM/ASK
Input sensitivity: 118 dBm
Input load: 50 Ohm
Power supply: 12 – 24 Vac/dc ( autodetect)
Consumption max: 120 mA @12Vac
Peak consumption: 500 mA at power up
Max switching power: 10 A @ (30 Vdc)
Contact NO: 6 A @ (30 Vdc) – Contact NC
Relay number: 1
Operating modes: Pulse / Latch / Timed
Release time (Timed mode): from 1 sec. to 23h.59m:59s
Contacts: C-NO-NC
Memory capacity: 250 user codes
TX security code: KeeLoq® Hopping code
Max code combination number: 264
Operating temperature: 20°/+65°C
Housing protection: IP2X
Overall dimensions: 44 x 58 x 25 mm
Communication w/mobile phone: Bluetooth
Standard: BLE 4.2
IO : Compatibility: Android, iOS
Release Android: 5.1 and next
Release iOS: 10 and next

For iOS

For Android

Dimensions|

Dimensions

Warnings

The receiver allocation is very important for the best operation of the system. Place the receiver far from interference sources such
as big magnetic fields or radio emissions. The distance between 2 receivers must be at least1,5 m.

The equipment must be powered from a device that provides a safety extra low voltage (SELV) type LPS ( Low Power Source);
There must be a suitable disconnecting device to the current drawn by the receiver (90 mA max @ 12Vdc).

Wiring

Compatible transmitters

Erone – S2TR2641E2-E4-E2M
Erone – SETR2641AM1, SETR2641AM2
Erone – S3TR2641T1-T2-T4
Erone – S4TR2641E1-E2-E4
Erone – SETR2641TM
Erone – S7TR2641E4
Erone – FKT2641E1 – FKTHS2641E1- TTH2641E1
Erone – S4TR2641E1-E2-E4
CDVI – GALEOR

Color LED	Description
Green	Power ON

NO Bluetooth communication
Green-Orange blinking| Bluetooth communication in progress
Orange| Relay excited

The App “RX CUBE”

The setup of the receiver can be done only through the App “Rx Cube”. So, first of all, download the App from “Apple Store” or “Google Play”. You can find it both typing the name of the App, “RX Cube”, or searching simply CDVI and then selecting Rx Cube. Once downloaded, authorize the App to use the Bluetooth communication. The App will ask even the GPS localization: please authorize it for the full operating of the Bluetooth BLE.
The App “RX CUBE”

Start the App and press the scan button: the App begins scanning the surroundings searching for any Rx Cube is running in the range of the Bluetooth signal ( 10 — 30 m ). Much depends on the fixing position of the receiver and whether the communication is direct or passes through walls. At the end of the scanning, the screen will show all the receivers Rx Cube found.

The receiver, by factory, comes with the name “CUBE”. If you power two or more receivers simultaneously, the scanning will list many receivers all identical: it is advisable to power one device at time and possibly rename it individually. The name of the device can have up to 12 characters.

Changing the factory name of the receiver

Type the default password 11111 (for administrator), click UNLOCK and enter in the main menu.
Select Settings.
Type the new name, give OK, then disconnect and make a new scanning..
The App will display the new name of the receivers.

Password

The access to the receiver has 2 different security levels: ADMINISTRATOR and INSTALLER.
Factory password for ADMINISTRATOR = 11111.
Factory password for INSTALLER = 00000.
Both can make all the settings. Only the Administrator can change the passwords, the Installer is not authorized

Memory

Enter the submenu Memory to manage the receiver memory : add or delete transmitters individually, add or delete a batch of transmitters, delete all the transmitters, restore the memory to factory settings.
Memory

Memorizing transmitters

Individually ( fig. 3)
The memorization can be done directly, pressing the button of the transmitter to store or specifying its S/N and Facility code. In this case you must specify the button/s authorized ( you can store up to 4 buttons).

In one block ( fig. 4)
Specify the number of transmitters of the block, the detail of the first transmitter ( S/N and Facility code ) and the buttons to enable ( A, B, C or D).

NOTE: The button Format allows to display the numbers in DECIMAL or HEXADECIMAL format.
Memory

Delete transmitters

Individually
Enter the S/N and Facility code of the transmitter to delete and press DELETE

In one block
Specify the number of transmitters of the block, enter S/N and Facility code of the first TX and press DELETE

Delete memory
Press DELETE to delete all the transmitters memorized

Factory Default
This option allows to delete all the transmitters and reset the settings to the factory defaults: pulse mode, time of the timed mode ( 5 sec.), name of the receiver ( CUBE).

Settings

Clicking on Settings it is possible to set the the relay operating mode: PULSE, STEP, TIMED. In pulse mode the relay remains activated for the entire duration of the radio transmission with a min. time of 300 mS. For the Timed mode it is possible to set the release time of the relay from 1 sec. to 23h : 59m : 59s.
Pulse mode

Step mode

Timed mode

Password

The password can be changed selecting the icon Password on the mail screen.
Only the ADMINISTRATOR is authorized to change the password.

The password set-in-factory are:

Administrator: 11111
Installer: 00000

The password is composed by max 5 numeric digits (min 1)
A red message appears if the password is still the factory password.
NOTE: The icon PASSWORD, in the main menu, is RED when at least one of the two password is still at the factory value

Info

The icon INFO of the main screen allows to display the features of the receiver: number of TX memorized, revision of the Firmware and release of the App.
It is possible to list the transmitters memorized: press List..> The screen displays only 5-6 lines of the list.
Scroll the list taping the center of the screen.
The Serial number of the transmitters can be displayed in Decimal or Hexadecimal format.
If you select one line, you display the information of a specific transmitter. For each transmitter it is displayed the FC + S/N and the button active ( A, B, C or D).
For changing this setting, press one of the 4 buttons and push CHANGE.
From this screen is also possible to DELETE the TX from the memory.

Command

It is possible to activate directly the relay from the App.
Enter the icon “Command” and press the button.
The symbol becomes RED confirming of the relay activation.

Disposal

This product is made up of various types of material, therefore, as indicated by the symbol in the figure, the product must not be disposed of in with the household waste.
Dispose in accordance with local current regulations.

Guarantee

The warranty period for this product is 60 months, beginning from the manufacturer date.
During this period, if the product does not work correctly, due to a defective component, the product will be repaired or substituted at our discretion.
The guarantee does not cover the plastic container integrity. After-sale service is supplied at the factory.

Manufacture

Manufactured by: CDVI WIreless SPA – Via Piave, 23
31020 S.Pietro di Feletto (TV) – Italy
Tel: +39-0438-450960 –
Fax: +39-0438-455628

CUSTOMER SUPPORT

CDVI AMERICAS
[CANADA – USA – LATIN AMERICA]
www.cdvi.ca
Manufactured by : CDVI Wireless SPA
Via Piave, 23 – 31020 S.Pietro di Feletto (TV) – Italy
tel: +39-0438-450860 –
mail: info@erone.com
web: www.erone.com
www.erone.com