CDVI A10U48 Mid and Long Range UHF Reader Instruction Manual

Mid & Long Range UHF Reader
A6U48 / A10U48
AES128 ENCRYPTION
CHIFFREMENT AES128

A10U48 Mid and Long Range UHF Reader

Thank you for purchasing our products and for the confidence you placed in CDVI.
U4G0 Range and references

PRODUCT PRESENTATION

RF Module

• Works in two operating modes :
• Stand-alone mode: Manage up to 7560 UHF credentials and 100 remote keys
• Wiegand mode (26-, 30- or 44-bit supported): Maximum UHF credentials and remotes management depends on the capacity of the access control system
• Relay operating modes (2 x 24 VA – 48 VDC rated relays): Pulse, step, delayed (delay from 1 sec. to 23 h : 59 min)
• Operating frequency range 433 MHz (Rolling code whit AES128 encryption)
• RS485 wiring between the UHF reader and RF module (Two UHF readers supported per RS485 port)
• Power requirements: 12/24 VAC/DC
• Current consumption: 25 to 50 mA (max) @ 12 VDC
• Operating temperature: -10°C to 60°C
• Weight: 65 g
• IP55 enclosure protection
• Demodulation GFSK
• Sensitivity (for good signal): -115 dBm

UHF Readers

• Operating frequency range of 865 – 868 865 – 868 MHz
• Detection range in open space: A6U48: (6 m) and A10U48: (10 m)
• RF output power: Up to 30 dBm (adjustable)
• Current consumption: 350 mA (max. 650 mA)
• Operating temperature: -25°C to 80°C
• Weight: A6U48: 0.9 Kg and A10U49: 2,4 Kg
• Protocol tag supported: ISO18000-6B, ISO18000-6C, EPC C1G2
• Transmission type: FHSS
• Dimensions: A6U48: 235 x 235 x 57 mm A10U48: 445 x 445 x 55 mm

PACKAGE CONTENTS

This chapter details how to install and setup the U4GO A6U48 or A10U48 .
Kit deinstallation

| | |
---|---|---|---
A6U48 Or A10U48| Alimentation| Receptor radio| Fixation support
1| 1| 1| 1

MOUNTING INSTRUCTIONS

A6U48 – Mounting diagram

RF MODULE – Mounting diagram
Option A
A10U48 – Mounting diagram

Use of PG7 cable glands (not provided)

WIRING DIAGRAM

Description| Wire type| Optional extension size| Maximum length
---|---|---|---
RS485 BUS| 2 conductors ( RS485  bus)
2 conductors ( Power supply)| 24AWG ( 0,51 mm²)18AWG ( 1,02mm²)| 1220 m
L1 = 32 m MAX
Wiegand BUS| 3 conductors Belden 9553| 22AWG ( 0,64 mm² ) to 18AWG ( 1,02 mm²)| 150 m
Power supply| 2 conductors| 18AWG ( 1,02 mm²)| L1 = 32 m MAX

Side Installation

PROGRAMMING

Menu Commands:

U4GO Menus

The next steps explain in detail the different menus and their configurations.
SET THE OPERATING MODE (OUTPUT)
Scroll to the “menu Output” then press “P3”

The U4GO system work in two different operating mode “Output”:
“RELAY” mode (stand-alone):
Manage up to 7560 UHF credentials and 100 remote keys in stand-alone (relay activation ONLY).
“WIEGAND” mode (Connect to online access control system): Maximum UHF credentials and remotes management depends on the capacity of the access control system.
Select one then press “P3” to confirm
IMPORTANT: The relays won’t work in “Wiegand” mode
ADDING UHF CREDENTIAL
There are two ways to register a UHF credential: One at a time or in one block (batch).
Adding UHF credential one at a time

Present the UHF credential to the reader or type manually its serial number
(Note: use “P4” to shift left).

Add UHF credential in one block
You can also register multiple UHF credentials in one block. The serial numbers of each UHF credentials must follow each other in series. Simply confirm the number of UHF credentials to register and then present the first one in the series .

Type the number of UHF credential to register
Press “P1” to select then “P3” to confirm
Present the first UHF credential of the serie to the reader or type manually its serial number
(Note: use “P4” to shift left).

DELETING UHF CREDENTIAL
Delete UHF credential one at a time

Delete UHF credential in one block
You can also delete multiple UHF credentials in one block (batch). The serial numbers of each UHF credentials must follow each other in series. Simply confirm the number of UHF credentials to register and then present the first one in the series.

Delete remote from the list
This is useful when you do not have the remote control in your hand but only its serial number from a list.

Delete ALL UHF credential at once

ADDING REMOTE (TX)

** The “Add Tx” menu is required in “Relay” mode ONLY. See “1. Set the operating mode (output)”. You can add up to 100 remote controls. A remote control can activate either relay 1 or relay 2.
There are three ways to register a remote (Tx): one at a time, by associating a button to a specific relay or in one block (batch).
Add remote one at the time**

Add remote and associate a button to a specific relay (“Relay” output mode ONLY)

Add remote in one block
You can also add many remote controls in one block (batch). The serial numbers of each remote control must follow each other in series. Simply confirm the number of remote control to register and then present the first one in the series .

DELETING REMOTE (TX)
Delete remote one at a time (will completely remove the remote)

Delete remotes in one block
You can also delete multiple remotes in one block (batch).
The serial numbers of each remote must follow each other in series. Simply confirm the number of remotes to delete and then present the first one in the series.

Delete remote from a list
This way is useful when you do not have the remote control in your hand but only its serial number from a list.

Delete all remotes

SETTING

CONFIGURATION

Wiegand Output Settings

Relay Output Settings

Relay activation per remote buttons

BACKUP
Upload or downoad the full data-ase using an external memory card

1. Plug-in the memory into the connector (Red Rubber Memory = 512 Kbit)

![CDVI A10U48 Mid and Long Range UHF Reader - fig1]34](https://manuals.plus /wp-content/uploads/2023/04/CDVI-A10U48-Mid-and-Long-Range-UHF-Reader- fig134.jpg)

Restoring from the external memory will overwrite ALL module database .
OPTION
The menu “Option” allows you to enable (“ON “ or “OFF”) the “Auto-installing” feature.
The “Auto-installing” feature allows you to register other remote controls from any remote control already memorized in the module.
IMPORTANT NOTE: One remote must be memorized in the receiver.
Memorization of a new remote (Tx)
Place the two remote (“Memorized Tx” and the “New Tx”) next to each other then do the following:

Once the new remote has been “Authorized”, stand next to the receiver and press button A for 1 sec .
The receiver makes a long beep: The remote has been memorized and is ready for use.
It may take up to 6 seconds for the receiver before hearing the confirmation beep of a “New Tx” .
IMPORTANT NOTES :

1. Must be a remote already memorized in the receiver.
2. If you press any button of the authorized “New Tx” out of reception range of the receiver more that 15 times, the autoinstalling property stops and the procedure must be restarted.

INFORMATION

UHF CREDENTIAL INSTALLATION
Choose one of the six places (A-F) on the windshield as showed in the figure below to install.
According to the European Standard, some vehicles with metalized windshield have a reserved area (not metalized) for RFID tags so choose position B.

For optimum performance, install the UHF credential on the same side of the reader.
(left side A or F, Right side C or D and overhead B or E).
NOTE : When there is a metalized windshield, the read range of the reader will be affected.
Please test the performance before using it .

PARKING OR GARAGE APPLICATION DIAGRAM

USING AND INSTALLING UHF CREDENTIAL
Regular ISO or Clamshell UHF Credential
Use a card to test reader position for optimal performance.
Attention: the card is very sensitive to the human hand.
The performance of detection can drastically change according to the way of holding the cards.
Look at the following images to understand the best way to hold the card

Hold the card with an outstretched arm, away from the body.
If the card is held near the body the performances can decrease a lot.
A card held in a wallet cannot be detected.
A card in touch with the clothes cannot be read.|
UHF Windshield Sticker Credential (ATU48)
The UHF windshield sticker position is similar to the card, as described above.
Best use on the surface of a window or headlights.
IMPORTANT: Once fixed, the UHF windshield sticker cannot be ripped off and reused.
Please test the performance before installation.
UHF Licence Plate UHF Credential (PTU48)
Use only for licence plates. Use the screws to fix the tag on the bottom of the licence plate.
Please test the performance before installation .
WIEGAND OUTPUT FORMATS
The wireless receiver converts the serial number of the UHF credentials and the remotes (Tx) in Wiegand format. The architecture of the Wiegand signal is different according to the number of bits set ( 26, 30 or 44 bit).
Wiegand UHF Credential Format

bit )
Wiegand 30| Bit 1| Bit 2 – 5| Bit 6 – 29| Bit 30
Even Parity ( 1 bit )| [ 4 bit Address ]|  [ 24 bit S/N ]| Odd Parity ( 1 bit )
Wiegand 44| Bit 1-4| Bit 5 – 8| Bit 9 – 40| Bit 41 – 44
0000 ( fixed )| [ 4 bit Address ]|  [ 32 bit S/N ]| LRC (**)

Wiegand Remotes (Tx) Format

bit )
Wiegand 30| Bit 30| Bit 6 – 29| Bit 2 – 5| Bit 1
Odd Parity ( 1 bit )|  [ 24 bit S/N ]| [ 4 bit Button ] ()| Even Parity ( 1 bit )
Wiegand 44| Bit 1-4| Bit 5 – 8| Bit 9 – 40| Bit 41 – 44
0000 ( fixed )| [ 4 bit Button ] ()|  [ 32 bit S/N ]| LRC ()
Button| Code**
---|---
A| 1010
B| 1011
C| 1100
D| 1101

(*) The 4 buttons remote are in hexadecimal format. See the table beside.
(**) Longitudinal Redundancy Check

CDVI Group
FRANCE (Headquarters)
Phone: +33 (0) 1 48 91 01 02| CDVI FRANCE + EXPORT
+33 (0) 1 48 91 01 02
www.cdvi.com| CDVI AMERICAS [CANADA – USA]
+1 (450) 682 7945
www.cdvi.ca
---|---|---
CDVI BENELUX [BELGIUM – NETHERLANDS – LUXEMBOURG]
+32 (0) 56 73 93 00
www.cdvibenelux.com| CDVI SUISSE
+41 (0) 21 882 18 41
www.cdvi.ch| CDVI IBÉRICA [SPAIN – PORTUGAL]
+34 (0) 935 390 966
www.cdviberica.com
CDVI ITALIA
+39 (0) 321 90 573
www.cdvi.it| CDVI GERMANY
+49 0175-2932 901
www.cdvi.de| CDVI MAROC
+212 (0) 5 22 48 09 40
www.cdvi.ma
CDVI NORDICS [SWEDEN – DENMARK – NORWAY – FINLAND]
+46 (0) 31 760 19 30
www.cdvi.se| CDVI UK [UNITED KINGDOM – IRELAND]
+44 (0) 1628 531300
www.cdvi.co.uk| CDVI POLSKA
+48 (0) 12 659 23 44
www.cdvi.com.pl

All the information contained within this document (pictures, drawings, features, specifications and dimensions) could be perceptibly different and can be changed without prior notice.

www.cdvigroup.com

References

• Fabrikant van toegangscontrole-oplossingen - CDVI Benelux

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>