CDVI V5SR 500kg Surface Mount Electromagnetic Lock Instruction Manual

: June 12, 2024
: CDVI

Table of Contents

CDVI V5SR 500kg Surface Mount Electromagnetic Lock
Product Information
Product Usage Instructions
Electrical Connections
Recommended Power Supplies
Security Rope Installation
Contact Information
PRODUCT PRESENTATION
SYMBOLS
PACKAGE CONTENT
ELECTRICAL CONNECTIONS
Installation Instructions
MOUNTING RECOMMENDATIONS
CONNECTION DIAGRAMS
MAINTENANCE / TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CDVI V5SR 500kg Surface Mount Electromagnetic Lock

Product Information

Product Name	V5SR 500 kg Surface Mount Electromagnetic Lock
Manufacturing Year	1985
Features

Monitored
Surface mount
High corrosion resistance
Safety rope
No mechanical wear
No residual magnetism
Ease of installation
Recommended for interior use
Fail safe (Door unlocked when power off)
Holding force: 500 kg
Visual indication (Blue = Locked ; Green = Open)
Built-in varistor: built-in electronic protection to eliminate
back EMF
Dimensions (L x W x D): 272 x 66 x 40 mm
Armature plate dimensions (L x W x D): 185 x 60 x 12 mm
Power supply: 12-24V dc
Consumption: 290 mA @ 12V dc, 145 mA @ 24V dc
IP42
WEEE & RoHS
CE Certification
UKCA Certification

Package Content|

Wood screw
Magnetic lock
Armature plate
Roll pin
Cap nut
Fixing plate
Security rope
M8 Screw
Steel washer
Rubber washer
MOUNTING RECOMMENDATIONS

Electrical Connections|

Voltage: 12V dc (Default setup)
Terminal Description:
- + : Power supply positive terminal
- N.C : Normally closed terminal
- COM : Common terminal
- N.O : Normally open terminal

Product Usage Instructions

Mounting Recommendations

To properly mount the electromagnetic lock, follow these steps:

Attach the magnetic lock and armature plate securely to their supports.
Ensure the magnetic lock and the armature plate are aligned.
Mount the armature plate floating around the central mounting screw to compensate for any door misalignment.

Electrical Connections

When connecting the lock to the input current, make sure to:

Check the jumper position before connecting the lock to avoid
damaging it. Incorrect jumper position can void the warranty.
Ensure the magnet and the armature meet evenly over their entire facing surfaces.
Allow the armature plate to pivot slightly about its center mounting screw to compensate for any door misalignment.

Recommended Power Supplies

Voltage	Recommended Power Supply
12V	ADC335, ADC612S
24V	ADC324, PSMB242

Security Rope Installation

To ensure the safety of users and prevent the electromagnetic lock from detaching, follow the steps below:

Install the two safety ropes as shown in the diagram.

Contact Information

If you have any further questions or need support, please contact CDVI using the following contact details:

CDVI UK [UNITED KINGDOM IRELAND] – Phone: +44 (0)1628 531300 – Website: www.cdvi.co.uk
CDVI NORDIC [SWEDEN – DENMARK NORWAY FINLAND] – Phone: +46 (0)31 760 19 30 – Website: www.cdvi.se
CDVI AMERICAS [CANADA – USA – LATAM] – Phone: +1 866 610 0102 – Website: www.cdvi.ca
CDVI BENELUX [BELGIUM – NETHERLAND LUXEMBOURG] – Phone: +32 (0) 56 73 93 00 – Website: www.cdvibenelux.com

PRODUCT PRESENTATION

Surface mount
High corrosion resistance
Safety rope
No mechanical wear
No residual magnetism
Ease of installation
Recommended for interior use
Fail safe (Door unlocked when power off)
Holding force: 500 kg
Visual indication (Blue = Locked ; Green = Open)
Built-in varistor: built-in electronic protection to eliminate back EMF
Dimensions (L x W x D): 272 x 66 x 40 mm
Armature plate dimensions (L x W x D): 185 x 60 x 12 mm
Power supply: 12-24V dc
Consumption: 290 mA @ 12V dc 145 mA @ 24V dc

SYMBOLS

IP42
WEEE & RoHS
CE Certification
UKCA Certification

PACKAGE CONTENT

ELECTRICAL CONNECTIONS

12V dc Default setup

Terminal	Description
+	12 or 24V dc
–	0V
N.C	NC (Normally closed)
COM	COM
N.O	NO (Normally open)

The NO/NC signal only switches when the door is closed with the power switched on.

Voltage selection jumpers

IMPORTANT NOTE

Check the jumper position before connecting the lock to the input current. Having it in the wrong position could damage the lock. This type of damage is not covered by the warranty.
Make sure that the magnet and the armature meet evenly over their entire facing surfaces.

The armature plate must be able to pivot slightly about its center mounting screw to compensate for any door misalignment.

Recommended power supplies

Installation Instructions

MOUNTING RECOMMENDATIONS

Armature plate

It is vital that the magnetic lock and armature plate are securely fixed to their supports.
The magnetic lock and the armature plate must be aligned.
The armature plate must be mounted “floating” around the central mounting screw to compensate for any misalignment of the door.

The security rope

Throughout its life, an electro-magnetic lock is subject to an accumulation of repeated shocks and stresses at the fixing points on the door frame.
Frequent opening and closing of the door as well as attempts of opening a locked door or acts of vandalism can cause the maglock to detach from its mounting support or bracket. In order to avoid the risk of the electro-magnetic lock falling, the two safety ropes can be installed to guarantee the safety of users. (see diagram above).

CONNECTION DIAGRAMS

(CONFORMS NF S61-937 – PV n° SD 18 00 59)

Synoptic 1

BBG: Glass breakage box
The BBG must be placed close to the emergency exit and be accessible in the direction of the evacuation.

Synoptic 2

The BRC box is essential for NF S61-937 compliance and must be reset by pressing button l1 located inside of the box.

Synoptic 3

The BRC box is essential for NF S61-937 compliance and must be reset by pressing button l1 located inside of the box.
The BBG must be placed close to the emergency exit and be accessible in the direction of the evacuation.

MAINTENANCE / TROUBLESHOOTING

In order to sustainably maintain the performance of your powered safety devices, we recommend :

Perform a periodic functional test of your facility.
Visually inspect the condition of different components of the installation in order to prevent deterioration of the wiring and the appearance of rust on the surfaces of electromagnetic devices.
Systematically correct any anomaly of a nature compromise the security of your installation.

Reference should also be made to the standard NF S61-933 concerning the rules of operation and maintenance.

CDVI FRANCE + EXPORT