CP Electronics GIMB Batten Mount PIR Detector User Guide

CP Electronics GIMB Batten Mount PIR Detector

Overview

The GIMB miniature PIR (passive infrared) presence detector provides automatic control of lighting loads. It is specifically designed for mounting onto a batten style luminaire. The detector can switch incandescent, fluorescent, compact fluorescent, and LED lighting. It detects movement using a PIR sensor and turns the load on. When an area is no longer occupied, the load will switch off after a 10-minute timeout period. A selection of fixing washers are supplied to aid fixing to a variety of luminaires.

Installation

Do not grip the unit at the lens end. Hold the square body near the threaded end when installing and tightening the nut. Care must be taken to prevent damage to the lens and surrounding IP seal. Ensure that the silicone washer and/or the IP spacer are used to ensure IP rating.

Components

Technical Data

2 Amps compact fluorescent lighting
2 Amps low energy lighting
2 Amps low voltage lighting (switch primary of transformer)
Switch SON lighting loads via a contactor
Power consumption| On: 799mW
Off: 807mW
Cable specification| 1m 1/1.13 solid core cable
Temperature| –
Humidity| 5 to 95% non-condensing
Material| Flame retardant ABS/PC
Type| Class 2
IP rating| IP65
Compliance| EMC-2014/30/EU
LVD-2014/35/EU

Important Notice

This device should be installed by a qualified electrician in accordance with the latest edition of the IEE Wiring Regulations and any applicable Building Regulations.

For further compliance information, visit www.cpelectronics.co.uk/compliance

Due to our policy of continual product improvement, CP Electronics reserves the right to alter the specification of this product without prior notice.

Contact Information:

• C.P. Electronics Ltd Brent Crescent London NW10 7XR United Kingdom
• Tel: + 44 (0) 333 900 0671
• Fax: + 44 (0) 333 900 0674
• Website: www.green-iswitches.co.uk
• Email: enquiry@green-iswitches.co.uk
• Ref: #WD639 Issue 6

Batten mount PIR detector

Overview

The GIMB miniature PIR (passive infrared) presence detector provides automatic control of lighting loads. It is specifically designed for mounting onto a batten style luminaire.  The detector will switch incandescent, fluorescent, compact fluorescent and LED lighting. The unit detects movement using a PIR sensor and turns the load on. When an area is no longer occupied the load will switch off after a 10 minute time out period. A selection of fixing washers are supplied to aid fixing to a variety of luminaires.

Detection diagram

Note: illustration shows an average of the walk across and walk towards figures below.

Walk across

Walk towards

Installation

Do not grip unit at the lens end. Hold the square body near the threaded end when installing and tightening the nut. Care must be taken to prevent damage to the lens and surrounding IP seal.

Components

Part/Quantity Supplied

• IP Spacer with silicone coating 1
• Silicone washer 1
• 5º washer 1
• 5º spacer 1
• M20 nut 1

Mounting hole without key

Mounting hole with key

Note. Key to be at top of sensor.

Standard luminaire fitting

IP luminaire fitting

Important
Ensure that the Silicone washer and/or the IP spacer are used to ensure IP rating.

Note. Use the 5º spacers where the luminaire housing has a draft angle .

The product is designed to be mounted directly to the outside of a luminaire. The detector should be sited so that the occupants of the room fall inside the detection pattern (shown opposite), at a recommended ceiling height of 2.8m. Note that the lower the sensor is installed the smaller the detection range will be, subject to the parameters shown on the detection diagram.

• Do not site within 1m of forced air heating or ventilation..
• Do not fix to a vibrating surface.

Wiring diagram

Power-up test procedure

• When power is applied to the unit, the load will turn on immediately.
• For the first 5 minutes of operation the time out period is 10 seconds to aid commissioning.
• Vacate the room or remain very still for more than 10 seconds and wait for the load to switch off.
• Check that the load switches on when movement is detected.
• When the 5 minutes have elapsed the time out will be 10 minutes.

Fault finding

What if the load does not turn ON?

• Check that the live supply to the circuit is good.
• Check that the load is functioning by bypassing the sensor (e.g. link L and L/ Out).

What if the load does not turn OFF?

• Ensure that the area is left unoccupied for longer than the 10 minute time out period.

Technical data

• Dimensions:

  • See diagrams opposite.

• Weight:

  • 0.10kg

• Supply Voltage:

  • 230VAC +/- 10%

• Frequency:

  • 50Hz

• Maximum Switching Load

  • 2 Amps fluorescent and incandescent lighting.
  • 2 Amps compact fluorescent lighting.
  • 2 Amps low energy lighting.
  • 2 Amps low voltage lighting (switch primary of transformer).
  • Switch SON lighting loads via a contactor.

• Power consumption On:

  • 99mW, Off 807mW

• Cable specification 1m:

  • 1/1.13 solid core cable

• Temperature:

  • -10ºC to 35ºC

• Humidity:

  • 5 to 95% non-condensing

• Material:

  • Flame retardant ABS/PC

• Type:

  • Class 2

• IP rating:

  • IP65
    Compliance

  • EMC-2014/30/EU

  • LVD-2014/35/EU

For further compliance information visit www.cpelectronics.co.uk/compliance

IMPORTANT NOTICE!
This device should be installed by a qualified electrician in accordance with the latest edition of the IEE Wiring Regulations and any applicable Building Regulations.

Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.

C.P. Electronics Ltd

• Brent Crescent London NW10 7XR United Kingdom
• Tel: + 44 (0) 333 900 0671
• Fax: + 44 (0) 333 900 0674
• www.green-iswitches.co.uk
• enquiry@green-iswitches.co.uk

References

• Home | Legrand
• Home | Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>