CP electronics EBR-CPIR-DALI Network Ceiling PIR with Photocell Installation Guide

June 12, 2024
CP electronics

CP-electronics-logo

CP Electronics EBR-CPIR-DALI Network Ceiling PIR with Photocell

CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-
product

Product Information

Product Name EBR-CPIR-DALI
Product Type DALI network ceiling PIR with photocell
Features
  • PIR Sensor: Detects movement within the unit’s detection range,
    allowing load control in response to changes in occupancy.

  • IR Receiver: Receives control and programming commands from an
    IR (infrared) handset.

  • Light Level Sensor: Measures the overall light level in the
    detection area.

  • Status LEDs: The LED flashes Red or Green to indicate the
    following:

    • Walk Test LED active when movement is detected
    • Valid setting received

Mounting Options| Flush fixing or Surface fixing using the optional Surface
Mounting Box (part no. DBB). (Note: EBR-CPIR-DALI-IP – use the
supplied gasket to ensure IP rating, not compatible with Surface
Mounting Box part no. DBB)
Supply Voltage| 9.5VDC – 22.5VDC via DALI
Current Consumption| 8mA
Type| IP40 (EBR-CPIR-DALI), IP55 (EBR-CPIR-DALI-IP)
Compliance| EMC-2014/30/EU, LVD-2014/35/EU

Overview

The EBR-CPIR-DALI presence detector provides automatic control of lighting. It is connected to the RAPID DALI Gateway via a DALI network. Functioning as a presence detector, the unit can turn lights on when a room is occupied and off when the room is empty. An adjustable internal light sensor provides light level information to the RAPID system to allow lights to be kept off if sufficient daylight is present, and to enable maintained illuminance for dimming systems. An integral IR sensor in the unit allows the unit to be commissioned, and used in conjunction with a remote control handset (part no: UHS) to:

  • Act as a conventional dimmer
  • Override the unit on or off

Product Usage Instructions

  • Front featuresCP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-fig-1
  • Back features

CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-
fig-2

DALI connection
Connection to the DALI bus via pluggable screw terminals. The DALI bus is polarity insensitive.

Installation

Choosing a Suitable Location

The EBR-CPIR-DALI is designed to be ceiling mounted and must satisfy the following criteria:

  • Avoid positioning the unit where direct sunlight may enter the sensor element.
  • Do not site the sensor within 1m of any lighting, forced air heating or ventilation.
  • Do not fix the sensor to an unstable or vibrating surface.
  • Do not exceed maximum length of cable (200m) on data bus.
  • Do not exceed maximum bus loading (200mA).

System wiring exampleCP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-
with-Photocell-fig-5

The EBR-CPIR-DALI is designed to be mounted using either:

  • Flush fixing, or
  • Surface fixing, using the optional Surface Mounting Box (part no. DBB). Both methods are illustrated below.

Note: EBR-CPIR-DALI-IP – use the supplied gasket to ensure IP rating (not compatible with Surface Mounting Box part no. DBB).

Flush Fixing

  1. Follow the wire stripping details provided in the manual.
  2. Mount the unit using the flush fixing method. Be careful when bending springs during mounting.CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-fig-8

Surface Fixing

  1. Follow the wire stripping details provided in the manual.
  2. Mount the unit using the surface fixing method with 50mm or 60mm fixing centers.CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-fig-9

Ensure that the cables are formed as shown before affixing the cable clamp. The clamp MUST clamp the outer sheath(s) only. Bend cores as shown.

System Wiring Example
Refer to the provided diagram for a system wiring example.CP-electronics-
EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-fig-10CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-
with-Photocell-fig-11

DALI bus loading
Devices (detectors / input units) and ballast combinations for 200mA supply. This assumes that the sensor LEDs are all on, and the sensor is receiving IR communication.

  • 4 devices and up to 64 ballasts

  • 5 devices and up to 55 ballasts

  • 6 devices and up to 44 ballasts

  • 7 devices and up to 33 ballasts

  • 8 devices and up to 22 ballasts

  • 8 devices and up to 22 ballasts

  • 10 devices and up to 2 ballasts
    In most realistic scenarios, only one LED is on at a time and only one detector is receiving IR; guidance changes to.

  • 10 devices up to 64 ballasts

  • 11 devices up to 60 ballasts

  • 12 devices up to 55 ballasts

  • 13 devices up to 50 ballasts

  • 14 devices up to 48 ballasts 15 devices up to 44 ballasts
    Addressing limits of DG64

  • 5 input units of 7 channels each

  • 10 detectors

Technical Data

  • Dimensions: See diagrams opposite
  • Weight :0.07kg
  • Supply Voltage :9.5VDC—22.5VDC via DALI Current consumption       8mA
  • DALI bus: Cannot be considered as SELV since DALI, ballasts only offer basic insulation, therefore all devices on the DALI bus must be wired as if carrying mains potential.
  • Terminal Capacity :2.5mm2 Temperature  -10ºC to 35ºC
  • Humidity: 5 to 95% non-condensing
  • Material (casing): Flame retardant ABS and PC/ABS Compliance
  • Type:  Class 2
  • IP rating :
    • EBR-CPIR-DALI         IP40
    • EBR-CPIR-DALI-IP        IP55
  • Compliance :EMC-2014/30/EU LVD-2014/35/EU

EMC-2014/30/EU, LVD-2014/35/EU. For further compliance information, visit www.cpelectronics.co.uk/compliance

Detection diagramCP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-
Photocell-fig-15

Sensor Accessories

Part Number Description
EBR-CPIR-DALI DALI network ceiling PIR with photocell
EBR-CPIR-DALI-IP DALI network ceiling PIR with photocell sealed to IP55
DBB Surface mounting box
UHS User handset override on/off; lux up/lux down
UHS3 User override remote handset on/off
UHS3 (2) User override remote handset, off only
UNLCDHS Universal LCD programming handset

IMPORTANT NOTICE
This device should be installed by a qualified electrician in accordance with the latest edition of the IEE Wiring Regulations and any applicable Building Regulations.

CP-electronics-EBR-CPIR-DALI-Network-Ceiling-PIR-with-Photocell-
fig-16Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.

CP Electronics – a business unit of Legrand Electric Limited Brent Crescent, London NW10 7XR UK Tel : +44 (0)333 900 0671 Fax : +44 (0)333 900 0674 VISIT AT www.cpelectronics.co.uk enquiry@cpelectronics.co.uk

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CP electronics User Manuals

Related Manuals