CP electronics MWS6-KNX Ceiling Flush Mounted Microwave Presence Absence Detector Installation Guide
- June 12, 2024
- CP electronics
Table of Contents
MWS6-KNX Ceiling Flush Mounted Microwave Presence Absence Detector
Installation Guide WD713 Issue 9 Installation Guide
MWS6-KNX
MWS6-KNX Ceiling Flush Mounted Microwave Presence Absence Detector
MWS6-KNX
KNX, ceiling, flush mounted, microwave, presence/absence detector
Attention
To be installed by competent technician with good understanding of network
devices.
Dimensions (mm)
Downloads and Videos cpelectronics.co.uk/cp/713
**** Microwave safety
The microwave radiation emitted by these units is extremely low power and
complies with ANSI standard “IEEEC95.1-1999 Standard for Safety Levels with
Respect to Human Exposure to Radio Frequency Electromagnetic Fields 3kHz
300GHz.”
Wiring
Key
- Switches, as configured in the ETS software.
- Low voltage only.
- KNX bus
Detection pattern
Presence or
absence detection
The unit requires configuration by an appropriate software.
Absence detection activation and switches configurations are set using the ETS
KNX software supplied by others.
It is designed to work with other KNX devices such as other detectors and
switches from other manufacturers.
Presence & absence explained 
cpelectronics.co.uk/cp/pa
Installation
This device is designed to be flush ceiling- mounted.
- Do not site the unit where direct sunlight might enter the sensor.
- Do not site the sensor within 1m of any lighting, forced air heating or ventilation.
- Do not fix the sensor to an unstable or vibrating surface.
- Avoid metallic objects directly in front of the sensor head.
- If the range is compromised by the ceiling construction or material, add the supplied 20mm spacer ring.
Create cut out
Cut a 64mm diameter hole in the ceiling.
Spacer ring
If the range is
compromised by the ceiling construction / material. Add the supplied 20mm
spacer ring.
Wire in plugs & connect to detector 
Wire
in plug/s, using wiring diagram on page 3 as a guide. Connect the plug/s to
the detector.
Install detector
Bend the springs up and push detector through
hole in ceiling. When fully inserted the springs snap back to hold the device
in place.
**** To avoid injury, take care when bending springs.
Technical Data
| Part code | MWS6-KNX |
|---|---|
| Weight | 0.150kg |
| Supply voltage DC | 30 VDC over KNX bus |
| Current consumption | 23.2mA |
Microwave sensors draw more current from the bus than a typical KNX device.
Please ensure that the bus power
supply has sufficient capacity to accomodate this device.
Terminal capacity| KNX: 1.2mm² over KNX connector Switch input: 2.5mm²
Working temperature range| -10 to 35ºC
Humidity| 5 to 95% noncondensing
Material (casing)| Flame retardant ABS and PC/ABS
Insulation class| 2
Microwave frequency| 5.8HGz
IP rating| 40
Compliance| **** RED-2014/53/EU
Accessories & associated products
| Part Number | Description | |
|---|---|---|
| EXD-HSC | Extended wiring housing | |
| UHS5 | Compact, programming | |
| UHS7 | Compact, user handset |
www.cpelectronics.co.uk
CP Electronics
Brent Crescent, London NW10 7XR
t. +44 (0)333 900 0671
enquiry@cpelectronics.co.uk
connect with us Energy services and technology association
Due to our policy of continual product improvement CP Electronics reserves
the right to alter the specification of this product without prior notice.
WD713 Issue 9 Installation Guide, MWS6-KNX
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>