VITEK VT-1353 MC Hair Clipper Instruction Manual

VT-1353
Hair clipper
Instruction Manual

VT-1353 MC Hair Clipper

HAIR CLIPPER VT-1353
This set is intended for cutting hair and styling.

DESCRIPTION

ATTENTION!
Do not use the unit near water in bathrooms, showers, swimming pools etc.

• When using the unit in a bathroom, unplug it right after usage by taking the power plug out of the mains socket, as closeness of water is dangerous even if the unit is switched off.
• For additional protection you can install a residual current device (RCD) with nominal operation current not exceeding 30 mA into the bathroom mains; contact a specialist for installation.

SAFETY MEASURES

Read this instruction manual carefully before using the unit and keep it for future reference for the whole unit operation period. Use the unit for intended purposes only, as specified in this manual. Mishandling of the unit may lead to its breakage and cause harm to the user or damage to his/her property.

• Before using the unit for the first time, make sure that the voltage in your mains corresponds to unit operating voltage.

• The power cord may not:
  – touch hot objects and surfaces,
  – be immersed into water,
  – run over sharp edges of furniture,
  – be used as a handle for carrying the unit.

• The hair clipper is not intended for professional use.

• Use the unit to cut only natural human hair, hair should be dry.

• Do not use the unit to cut artificial hair and animal hair.

• Use only the attachments supplied.

ATTENTION! Do not immerse the hair clipper, the power cord and the plug into water or any other liquids. Do not wash the clipper blades under water jet.

• Do not touch the hair clipper body and the power cord with wet hands.
• Do not use the unit outdoors.
• Do not use the unit in places with high temperature and relative humidity over 80%.
• Do not switch the unit on in places where aerosols are sprayed or highly flammable liquids are used.
• Do not keep the unit near a bath or a sink filled with water.
• If the unit is dropped into water, unplug it immediately, and only then take it out of the water.
• Never use the unit if the attachment combs are broken or damaged or if the blades are damaged.
• After each use clean the attachments and the blades with the brush to remove the cut-off hair.
• Make sure that the blades are clean and that there is lubricating oil on them.
• Never leave the operating unit unattended.
• Switch the hair clipper off during intervals in operation or when you are not using it.
• Do not leave children unattended to avoid them using the unit as a toy.
• Do not allow children to touch the hair clipper body and the power cord during the unit operation.
• During the unit operation and breaks between operation cycles, place the unit out of reach of children and disabled persons.
• This unit is not intended for usage by children.
• The unit is not intended to be used by people with physical, sensory or mental disabilities (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
• Close supervision is necessary when children or disabled persons are near the operating unit.
• For children safety reasons do not leave polyethylene bags used as a packaging unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
• Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center at the contact addresses given in the warranty certificate and on the  website www.vitek.ru.
• Transport the unit in the original package only.
• Keep the unit out of reach of children and disabled persons.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS AND WORK SPACES IS PROHIBITED. BEFORE THE FIRST USE
In case of the unit transportation or storage at low temperature keep it for at least three hours at room temperature.

• Remove all advertising stickers and packaging elements that can prevent the unit operation.
• Check the unit for damages; in case of damages do not use the unit.
• Before plugging the unit in make sure that the operating voltage of the unit corresponds to the voltage of your mains.

Blades (1)

• The blades (1) are consumables and they are not covered by the warranty.
• The consumer should check the condition of the cutting edges of the blades by themselves, as the sharpening (polishing) of cutting edges is not covered by warranty.
• If the blades (1) have been removed for cleaning or replacement, install them back, adjust and tighten the fastening screws.

Blade shifter (2)

• When you cut hair without using attachments (5, 6, 7, 8, 9, 10), you can shift the blade to adjust the cutting length (pic. 3).
• In the upper shifter (2) position haircut will be the shortest.
• In the lower shifter (2) position, the cutting length is approximately the same as when using 4-6 mm attachment comb (5).
• By changing the position of the shifter (2) while cutting hair, you can select the necessary cutting length.
• If hair is jammed in the blades (1) while cutting, move the shifter (2) from the upper position to the lower position or vice versa several times, this will help to release the jammed hair without removing the blades (1).
• When the hair clipper is switched on, move the shifter (2) several times from the upper position to the lower position or vice versa, this way you can remove the cut-off hair from the blades (1).
• If the hair clipper pulls hair while cutting, it means that the blades (1) became blunt, replace them with new ones.

Lubricating oil

• Before the first use check whether the blades (1) are lubricated, and, if necessary, lubricate them with the oil (11) supplied with the unit. Keep the blades (1) clean and lubricated.
• Do not use vegetable oil or oil with solvents. Solvents are subjected to evaporation, and the remaining thick oil can slow down the upper blade (1) moving speed.

HAIR STYLING INSTRUCTIONS

Before every use of the hair clipper always clean the blades (1) off hair, dust or any foreign inclusion, lubricate the blades (1) and check their adjustment.

• Hair should be clean and dry during hair cutting.
• Unwind the power adapter (14) cord to its full length.
• Insert the power plug into the mains socket.
• Before cutting hair switch the hair clipper on by setting the switch (4) to the upper position, the LED display (13) will light up on the unit body, indicating the clipper charging level in %. Upper value – charging level %, bottom value – remaining battery %. Make sure that the hair clipper operates normally and the blades (1) move smoothly. If there is excess oil on the blades (1), switch the hair clipper off moving the power switch (4) to the lower position and remove the excessive oil with a dry cloth.
• Constantly check the power cord, prevent it from multiple twisting, regularly switch the unit off and straighten the power cord.
• Seat a person so that his/her head is approximately at your eye level, cover the person’s shoulders with a towel and set hair with the comb.

Reminder

• Cut off a small amount of hair at a time – if necessary you can always return to the cut area of hair again for additional cutting.
• The best haircutting results are reached on dry hair, not wet.
• Comb the hair with a comb to reveal uneven locks.
• It is better to leave longer hair after cutting for the first time.
• After learning your clipper better, you will be able to arrange your hair in any style you need.

Attachment combs
The cut-off hair length depends on the attachment comb:

• attachment comb (5): length of hair left 4-6 mm;
•  attachment comb (6): length of hair left 7-9 mm;
• attachment comb (7): length of hair left 10-12 mm;
• attachment comb (8): length of hair left 16-18 mm;
•  attachment comb (9): length of hair left 22-24 mm;
• attachment comb (10): length of hair left 28-30 mm.

Install the selected attachment comb on the blades, teeth up, and press on the ledge in the bottom part of the attachment until locking. Before cutting hair make sure that the attachment is locked on its installation place.
To remove the attachment comb press the clamp and remove the attachment.
Step one
Install the attachment comb (5) or (6) (pic. 1).
Switch the hair clipper on using the power switch (4), setting it to the upper position. Hold the hair clipper with the blades (1) pointed upwards. Start cutting from the hair growth edge. Slowly move the hair clipper upwards.
This way cut all hair at the bottom of the back of the head and near the ears.
Step two
Switch the hair clipper off with the power switch (4) by setting it to the lower position, unplug the unit, then set the attachment comb (7, 8, 9) or (10) for longer hair and continue cutting hair near top of the head.
Step 3 – cutting in the temples area
Switch the hair clipper off and unplug it, then set the attachment comb (5) or attachment comb (6) and cut hair in the area of temples. Then set the 9 mm attachment comb (7, 8, 9) or attachment comb (10) and continue cutting towards the top of the head.
Step 4 – cutting the crown of the head
Using the attachment comb (7, 8, 9) or attachment comb (10), cut the hair on the top of the head towards the crown against the hair growth direction.

• You can cut hair against and along the direction of hair growth, but keep in mind that the hair cut against the growth will be shorter than the hair cut along the growth.
• Use the attachment comb (5) and attachment comb (6) for very short haircut. To leave a little longer hair, use the attachment comb (7, 8, 9) or attachment comb (10).
• To leave longer hair, grip hair locks between your fingers and cut the hair off using the clipper.
• You may use a comb: lift the hair locks and cut them with the hair clipper above the comb.
• Always start cutting from the head back.
• Comb the hair with a comb to reveal uneven locks.
• Use the scissors to make haircut even.

Step 5 – the final part

• In the final stage of hair cutting remove the attachment comb from the unit (pic. 2), turn the blades (1) of the clipper towards the hair and trim hair on the temples and neck carefully. Do not press the clipper strongly, there is danger of injuries or cuts when  pen blades (1) come in contact with skin.

Cone-shaped haircut
Set the necessary attachment comb and start cutting from the head back towards the crown. Cut the hair against the direction of the growth, towards the crown, and from the sides. To get a flat top haircut, use the comb: lift the locks and cut them along the comb. Comb the hair to reveal uneven locks.
After cutting your hair, switch the hair clipper off by setting the switch (4) to the lower position and unplug it.

CLEANING AND MAINTENANCE

Lubricating the blades
Lubricate the blades (1) before and after every use of the hair clipper with the oil (11) supplied with the unit.

• Switch the unit off using the power switch (4) and unplug it.
• Apply one-two drops of oil (11) on the blades (1) teeth and on the back side of upper blade, switch the hair clipper on and make sure that the blades are moving smoothly.
•  Switch the unit off, clean the excess oil with a dry cloth.

Attention! Use only the oil (11) supplied with the set. DO NOT USE vegetable oil, fat, oil mixed with any sol- vents for lubricating. Solvents will evaporate, leaving thick grease that may slow down the  lades’ motion.
Cleaning the hair clipper

• Switch the hair clipper off and unplug it.
•  Clean the blades (1) from the cut hair using the cleaning brush (12).
• Wipe the accessories and the hair clipper body (3) with a slightly wet cloth, and then dry them with a soft cloth.
• Do not immerse the hair clipper into water or other liquids.
• Do not use solvents or abrasives for cleaning the hair clipper body.

STORAGE

• Clean the hair clipper and lubricate the blades (1) with oil (11) before taking it away for storage.
• Keep the hair clipper in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Hair clipper (with blades) – 1 pc.
Attachment comb – 6 pc.
Lubricating oil – 1 pc.
Cleaning brush – 1 pc.
Power Supply Unit – 1 pc.
Instruction manual – 1 pc.
Warranty certificate – 1 pc.

TECHNICAL SPECIFICATIONS

Hair clipper
Built-in rechargeable battery: Li-on 110 0 mAh 3,7 V
Continuous operation time: 90 minutes
Battery charging time: 150 minutes
Input voltage: 5 V **1000 mA
Power Supply Unit
Power supply: 100-240 V ~50 Hz 0.2 A
Output voltage: 5 V **1000 mA
ATTENTION! Do not use the unit near water in the bathrooms, showers, swimming pools etc.
The manufacturer preserves the right to change design, structure and specifications not affecting general principles of the unit operation without a preliminary notification due to which insignificant differences between the manual and product may be observed. If the user reveals such differences, please report them via e-mail info@vitek.ru for receipt of an updated manual.

RECYCLING

** For environment protection do not throw out the unit and the batteries (if included), do not discard the unit and the batteries with usual household waste after the service life expiration; apply to specialized centers for further recycling.
The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product.
Unit operating life is 3 years
Guarantee**
Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased.
The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.
This product conforms to the EMC Directive 2014/30/EU and to the Low Voltage Directive 2014/35/EU.
A production date of the item is indicated in the serial number on the technical data plate. A serial number is an eleven-unit number, with the first four figures indicating the production date. For example, serial number 0606ххххххх means that the item was manufactured in June (the sixth month) 2006.

www.vitek.ru

References

• Бытовая техника Vitek - официальный сайт производителя мелкой бытовой техники для дома и ухода за собой Vitek.ru
• Бытовая техника Vitek - официальный сайт производителя мелкой бытовой техники для дома и ухода за собой Vitek.ru

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>