LNC LUVAQF370W1H8C Blobfish 5.1 In W 1 Light Polished Gold Modern Contemporary LED Wall Sconce Instruction Manual
- June 13, 2024
- LNC
Table of Contents
LNC LUVAQF370W1H8C Blobfish 5.1 In W 1 Light Polished Gold Modern
Contemporary LED Wall Sconce
Product Information:
- Item Number: A04970W1
- Maximum Wattage: Type B, Max 40W per bulb
- Voltage: 120V
- Contact Information: +1 850 296 2377 (Mon – Fri 9:00 – 16:00
- EST) | homecustomercare@outlook.com
Product Usage Instructions:
- Warning: To reduce the risk of fire, electric shock, or personal injury, we suggest installation by a licensed electrician.
- Read the instruction carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
- Ensure the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16 as required.
- Make sure the ceiling or wall can support the weight of the lamp before installation.
- Ensure the voltage used is 120V. Use Type B bulbs with a maximum wattage of 40W per bulb.
- Keep the lamp away from acidic and alkaline substances to avoid damaging the surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it cools down as bulbs can get hot quickly.
- Use common sense, caution, and care when using electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture:
PARTS INCLUDING:
(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Back plate (1)
(F) Stud (2)
(G) Arm (1)
(H) Socket (1)
(I) Glass shade (1)
(J) Socket ring (1)
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
Assembly & Installation Instructions:
- Remove the fixture from the carton and ensure all parts and accessories are included.
- Turn off the power before starting the installation.
- Secure the mounting plate (C) to the outlet box using the provided mounting screws (A).
- Connect the wires according to the provided wire connection chart. Note that the ground wire is a bare copper wire and should not be connected to other wires.
- Refer to the chart to connect the black or red supply wire and the white supply wire to the appropriate connections.
- For parallel cords, ensure to connect the square-shaped or ridged neutral wire and the round-shaped or smooth wire accordingly.
- Use the cupped washer for proper installation.
_ Note : _If you have any questions or need further assistance, please contact our customer care during working hours at +1 850 296 2377 or email us at homecustomercare@outlook.com.
Step A1 » Unscrew studs (F) from back plate (E), then set them aside for
later installation.
Step A2 » Carefully pass the supply wires from the outlet box through
mounting plate (C). Secure mounting plate (C) to the outlet box with mounting
screws (A).
Step A3 » Make wire connections. Connect wires as below wires connection
shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER
WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) and mounting plate (C), then
secure them with the previously removed studs (F).
Step A5 »
- Unscrew socket ring (J) from socket (H).
- Fix glass shade (I) to socket (H) with socket ring (J).
- Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>