LNC A04970W3 21.7-in 3 Light Polished Gold LED Modern Contemporary Vanity Light Instruction Manual
- June 13, 2024
- LNC
Table of Contents
LNC A04970W3 21.7-in 3 Light Polished Gold LED Modern Contemporary Vanity
Light
Product Information:
- Product Name: A04970W3
- Manufacturer: Unknown
- Contact Information: +1 850 296 2377 (Mon – Fri 9:00 – 16:00 EST)
- Email: homecustomercare@outlook.com
Item Number: A04970W3
Warnings:
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
Important Instructions:
- The mounting surface should be clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides.
- Ensure that the ceiling or wall can support the weight of the lamp before installation.
- Make sure the voltage used is 120V. The maximum wattage per bulb is Type B, Max 40W.
- Avoid contact with acidic and alkaline substances to prevent damage to the lamp’s surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it cools down.
- Follow common sense, caution, and care when using electrical products.
Tools Required (not included):
Before starting assembly and installation please prepare the needed tools as below picture.
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included:
- Mounting plate (C) x 1
- Green ground screw (D) x 1
- Back plate (E) x 1
- Stud (F) x 2
- Arm (G) x 1
- Socket (H) x 3
- Glass shade (I) x 3
- Socket ring (J) x 3
Accessories Enclosed:
- Mounting screw (A) x 2
- Plastic wire connector (B) x 3
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting the installation.
- Secure the mounting plate (C) to the outlet box using the provided mounting screws (A).
- Connect the wires according to the below chart:
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
OUTLET BOX GROUND | OUTLET BOX GROUND |
FIXTURE GROUND | DIMPLES |
CUPPED WASHER | FIXTURE GROUND |
Step A1 » Unscrew studs (F) from back plate (E), then set them aside for
later installation.
Step A2 » Carefully pass the supply wires from the outlet box through
mounting plate (C). Secure mounting plate (C) to the outlet box with mounting
screws (A).
Step A3 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Note : When using parallel wires (SPT I& SPT ll), the neutral wire is square-shaped or ridged, and the other wire will be round in shape or smooth.
Connect ground wires according to the below chart
Connect wires according to the below chart
Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) and mounting plate (C), then
secure them with the previously nremoved studs (F).
Step A5 »
- Unscrew socket rings (J) from sockets (H).
- Fix glass shades (I) to sockets (H) with socket rings (J).
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>