LNC A04993 8 Light Polished Gold Modern Contemporary LED Dry Rated Chandelier Instruction Manual
- June 13, 2024
- LNC
Table of Contents
LNC A04993 8 Light Polished Gold Modern Contemporary LED Dry Rated
Chandelier
Product Information
Item Number: A04993
Maximum Wattage: LED, 40W
Product Usage Instructions
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Ensure that the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.
- Check if the ceiling or wall can support the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 40W.
- Keep the lamp away from acidic and alkaline substances to avoid damaging the surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.
- Use common sense, caution, and care when using any electrical products.
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the provided illustration.
- Before starting the installation, turn off the power. NEVER attempt any work without shutting off the electricity until the work is done.
- Remove the mounting plate (C).
- Screw the unit to the top of the base (M).
- Screw lampshades (I) to the top of lampholders (J) as shown in the illustration.
- Connect wires as per the provided wire connection chart. Note that the ground wire is a bare copper wire and should never be connected to other wires.
- Connect the black or red supply wire to the appropriate outlet box ground.
- Connect the white supply wire to the fixture ground.
- Refer to the wire connection chart for further instructions based on the type of wire used.
If you have any further questions or need assistance, please contact our customer care team at +1 850 296 2377 during working hours (Mon – Fri, 9:00 – 16:00 EST) or email us at homecustomercare@outlook.com.
Item Number: A04993
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 40W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING:
- C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Stud (2)
- (F) Canopy (1)
- (G) Swivel joint (1)
- (H) Tube (1)
- (I) Lampshade (8)
- (J) Lampholder (8)
- (K) Arm-A (4)
- (L) Arm-B (4)
- (M) Base (1)
- (N) Connection terminal (1)
- (O) LED driving (1)
ACCESSORIES & QTY ENCLOSED:
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Unscrew studs (E) from canopy (F).
- Remove mounting plate (C).
- Adjust arms to proper position (be like 45° angle) as shown in the picture.
- Screw canopy (F) to the top of tubes (H) and then screw the unit to the top of base (M) Screw lampshades (I) to the top of lamp holders (J) as shown in the illustration.
- Please wire up the LED Driving first as shown in the illustration.
- Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below char
Connect wires according to the below chart
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is
square shaped or ridged and the other wire will be round in shape or smooth
(see illus.)
* Twist wires together with plastic wire connectors until tightly joined.
* Wrap each connector with approved electrical tape.
* Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Attach mounting plate (C) to the outlet box with mounting screws (B).
- Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening studs (E) onto the preassembled screws in mounting plate (C).
- Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Contact
- +1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST homecustomercare@outlook.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>