LNC LYJ22UV90H6G8C 6-Light Brushed Black and Polished Gold Modern Contemporary Mason Jar Linear LED Instruction Manual

LNC LYJ22UV90H6G8C 6-Light Brushed Black and Polished Gold Modern

Contemporary Mason Jar Linear LED

Product Information

• Item Number: A05090H6
• Maximum Wattage: Type B, Max 40W per bulb
• Voltage: 120V

Product Usage Instructions

1. We suggest installation by a licensed electrician.
2. Read the instruction carefully and save it for future reference.
3. Before starting, always shut off the electricity.
4. Ensure the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16 as required.
5. Make sure the ceiling or wall can support the weight of the lamp before installation.
6. Keep the lamp away from acidic and alkaline substances to prevent damage to the surface.
7. When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.
8. Follow common sense, caution, and care when using any electrical products.

Assembly and Installation Instructions

1. Carefully remove the fixture from the carton and check that all parts and accessories are included.
2. Screw tubes (I) to the top of the frame (J) and close quick links (G).
3. Turn off power before starting installation.
4. Mount the fixture, ensuring that the side of mounting plate (C) marked GND faces out and the canopy (E) is at least 6 inches above the mounting surface.
5. Connect wires according to the provided chart, ensuring not to connect any other wires to ground wires.

Important Instruction

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate(1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Loop (4)
• (G) Quick link (2)
• (H) Ball nut (2)
• (I) Tube
• (J) Frame (1)
• (K) Socket arm (6)
• (L) Socket (6)
• (M) Lampshade (6)

ACCESSORIES & QTY ENCLOSED

• (A) Wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation

   • Step A1 »
   1. Carefully pass the fixture wires through one side of tubes (I) and loops (F).
   2. Screw tubes (I) to top of frame (J).
   • Step A2 » Open quick links (G). Attach quick links (G) to loops (F) on canopy (E) and on the top of tubes (I). Close quick links (G).

3. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

4. Make installation

   • Step B1 » Unscrew ball nuts (H) from mounting plate (C).

   • Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
     Note: the side of mounting plate (C) marked “GND” must face out.

   • Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above canopy (E) is at least 6″.

   • Step B4 » Make wire connections
     Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

   • Twist wires together with plastic wire connectors until tightly joined.

   • Wrap each connector with approved electrical tape and sure that no wire strands are exposed.

   • Carefully tuck all wires into the outlet box.

   • Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening ball nuts (H) onto pre-assembled screws on mounting plate (C).
     NOTE: canopy (E) should be snug against the ceiling with ball nuts (H). If not, remove canopy (E), and adjust the threaded length of pre-assembled mounting screws on mounting plate (C):

   • First, unscrew the pre-assembled hex nuts.

   • Then, screw the pre-assembled mounting screws in or out of the mounting plate (C).

   • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B5.

   • Step B6 »

   1. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
   2. Carefully screw lampshades (M) onto sockets (L) as shown in the illustration.

5. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

+1 850 296 2377 Working hours: Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>