LNC A05090W1 9.4-in W 1 Light Matte Black and Polished Gold Modern Contemporary LED Wall Sconce Instruction Manual
- June 13, 2024
- LNC
Table of Contents
- LNC A05090W1 9.4-in W 1 Light Matte Black and Polished Gold Modern
- Product Information
- Product Usage Instructions
- Instruction
- IMAGE FOR FINISHED PRODUCT
- TOOLS REQUIRED (NOT INCLUDED)
- PARTS INCLUDING
- ACCESSORIES ENCLOSED
- ASSEMBLY & INSTALLATION INSTRUCTIONS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LNC A05090W1 9.4-in W 1 Light Matte Black and Polished Gold Modern
Contemporary LED Wall Sconce
Product Information
- Item Number: A05090W1
- Maximum Voltage: 120V
- Maximum Wattage : Type B, Max 40W per bulb
Product Usage Instructions
- We strongly recommend installation by a licensed electrician.
- Read the instruction manual carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16 as required.
- Ensure that the ceiling or wall can support the weight of the lamp before installation.
- The lamp operates at a voltage of 120V. Use Type B bulbs with a maximum wattage of 40W per bulb.
- Avoid contact with acidic and alkaline substances that may damage the surface of the lamp.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
- These safety instructions do not cover all possible conditions. Always exercise caution and use common sense when working with electrical products.
Instruction
- Item Number: A05090W4
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (4)
- (H) Lampshade (4)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Make assembly
-
Step A1 »: Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
-
Step A2 »: Carefully pass the supply wires from the outlet box through mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A). -
Step A3 »: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. -
Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (D):- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
-
Step A5
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Carefully screw lampshades (H) to sockets (G) as shown in the illustration.
Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>