BEGA 50 199.5 Wall Washer Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50 199.5 Wall Washer
Product Information
- Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
- Overvoltage protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
- LED Module: The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Defective glass must be replaced. Close the luminaire.
Product Usage Instructions
- Ensure that the installation and commissioning of the luminaire is carried out by a qualified electrician in accordance with national safety regulations.
- To protect against overvoltage, it is recommended to use separate overvoltage protection components, which can be found on our website at www.bega.com.
- If you need to replace the LED module, follow these steps:
- Disconnect the system and open the luminaire.
- Locate the label in the luminaire to identify the designation of the LED module.
- Obtain a replacement module from BEGA that matches the designation of the original module.
- Using standard tools, replace the module following the installation instructions provided by BEGA.
- If there is any defective glass, it must be replaced.
- Close the luminaire once the replacement is complete.
DIMENSION
Instructions for use
Application
Wall washer · indoor luminaire with symmetrical light distribution for the
illumination of wall surfaces with the mounting surface being the reflection
surface.
The luminaire can be installed with the light distribution opening upwards or
downwards.
Product description
- Die-cast aluminium and aluminium housing, finish Colour velvet black
- Matt safety glass
- Reflector made of pure anodised aluminium 2 mounting holes ø 4.5 mm
- Distance apart 200 mm
- 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminal and earth conductor terminal 2.5@ 2-pole connecting terminal for digital control LED power supply unit 220-240 V x 0/50-60 Hz DC 170-276 V
- DALI-controllable
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Impact strength IK07
- Protection against mechanical
- impacts < 2 joule
- r – Safety mark
- c – Conformity mark
- Weight: 2.9 kg
This product contains light sources of energy efficiency classes D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 32.7 W
- Luminaire connected wattage 36.1 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 40 °C
50 199.5 K27
- Module designation LED-0609/927
- Colour temperature 2700 K
- Colour rendering index CRI > 90
- Module luminous flux 4675 lm
- Luminaire luminous flux 4034 lm
- Luminaire luminous efficiency 111,7 lm / W
50 199.5 K3
- Module designation LED-0609/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 4830 lm
- Luminaire luminous flux 4168 lm
- Luminaire luminous efficiency 115,5 lm / W
50 199.5 K4
- Module designation LED-0609/940
- Colour temperature 4000 K
- Colour rendering index CRI > 90
- Module luminous flux 5025 lm
- Luminaire luminous flux 4337 lm
- Luminaire luminous efficiency 120,1 lm / W
Installation
- Undo hexagon socket head screws (wrench size 3 mm) through the opening in the luminaire housing up to the stop and lift luminaire top.
- Loosen earth connection (plug connection) and LED connection between luminaire top and luminaire base.
- LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
- Lead the mains supply cable through the cable entry of the luminaire base.
- Ensure correct directionality towards the area to be illuminated.
- Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
- Make the earth conductor connection and the electrical connection.
- For digital control please use the connecting terminal DA, DA.
- In case this terminal is not used the luminaire will be operated at full light output.
- Make earth connection (plug connection) and LED connection between luminaire top and luminaire base again.
- Install the luminaire top, press on and tighten screws evenly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
- Defective glass must be replaced.
- Close the luminaire.
Spares
- LED power supply unit DEV-0391/700
- LED module 2700 K LED-0609/927
- LED module 3000 K LED-0609/930
- LED module 4000 K LED-0609/940
- Reflector 76 001 484
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>