BEGA 31068 Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 31068 Wall Luminaire
Product Information
Instructions for use
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 31068 Wall Luminaire

BEGA-31068-Wall-Luminaire-product

Product Information

Product Name	Wandleuchte Wall luminaire Applique
Model Number	31 068
IP Rating	IP 44
Material	Die cast aluminium and hand-blown three-ply opal glass
Light Distribution	Uniform light distribution for a variety of lighting tasks
Lamp Module Connected Wattage	1.9 W
Luminaire Connected Wattage	2.7 W
Rated Temperature	25 – 60 degrees Celsius
Ambient Temperature	25 – 60 degrees Celsius
Colour Temperature	3000 K
Colour Rendering Index (CRI)	Greater than 80
Module Luminous Flux	375 lm
Luminaire Luminous Flux	238 lm
Luminaire Luminous Efficiency	88.1 lm / W

Instructions for use

Application
Wall luminiaire made of die cast aluminium and hand-blown three-ply opal glass. A luminaire with uniform light distribution for a variety of lighting tasks.

Product description

Luminaire made of aluminium and stainless steel
BEGA Unidure® coating technology
Opal glass
Silicone gasket
Mounting plate with 2 fixing holes ø 4.5 mm · 40 mm spacing
1 cable entry for mains supply cable up to ø 10,5 mm Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK06
Protection against mechanical
impacts < 1 joule
– Safety mark
– Conformity mark
Weight: 1.0 kg
This product contains light sources of energy efficiency class(es) C

Lamp

Module connected wattage: 1.9 W
Luminaire connected wattage: 2.7 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 60 °C

31 068 K3

Module designation: LED-0645/830
Colour temperature: 3000 K
Colour rendering index: CRI > 80
Module luminous flux: 375 lm
Luminaire luminous flux: 238 lm
Luminaire luminous efficiency: 88,1 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage Protection:

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against transients, it is recommended to use separate overvoltage protection components.
For more details, visit our website at www.bega.com.

Installation:

LEDs are high-quality electronic components, so avoid touching the light output opening of the LED directly during installation or relamping.
Undo screw at wall box and remove the mounting plate.
Lead the mains supply cable through the cable entry of the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
Make earth conductor connection between luminaire housing and mounting plate.
Note position of application of the luminaire “arrow down”.
Place the luminaire onto the mounting plate, adjust and fix it.
Screw glass with gasket into luminaire housing.

Spares

Spare glass with gasket: 11 002 688 41
LED power supply unit: DEV-0292/350
LED module 3000 K: LED-0645/830

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.