BEGA 50146.1 Wall Washer for Indoor Use Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50146.1 Wall Washer for Indoor Use
Product Information
The product is a luminaire that requires installation and operation in accordance with national safety regulations. It should only be installed and commissioned by a qualified electrician. The manufacturer is not liable for any damage caused by improper use or installation. The luminaire is equipped with electronic components that are protected against overvoltage according to DIN EN 61547. Additional overvoltage protection components are recommended for enhanced protection.
Product Usage Instructions
- Ensure that the luminaire is installed and operated in compliance with national safety regulations.
- Installation and commissioning should only be carried out by a qualified electrician.
- Do not make any modifications to the luminaire without proper authorization.
- For enhanced protection against overvoltage and other transients, consider using separate overvoltage protection components available on the manufacturer’s website.
- When replacing parts, use the following spares:
- LED Power Supply Unit: DEV-0388/700
- LED Module 3000 K: LED-0696/930
- LED Module 4000 K: LED-0696/940
- Reflector: 76 001 510
Dimensions
Application
- Wall washer · indoor luminaire for the glare free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.
Product Description
- Die-cast aluminium and aluminium housing, finish Colour velvet white Crystal glass, inside matt
- Reflector made of pure anodised aluminium
- 2 mounting holes ø 4.8 mm
- Distance apart 200 x 65 mm 2 cable entries for through-wiring of mains
- supply cable ø 7-10.5 mm, max. 5 G 1.5
- Connection terminal 2.5
- Earth conductor connection
- 2-pole connecting terminal for digital control
- LED power supply unit: 220-240 V 0/50-60 Hz
- DC 176-264 V
- DALI-controllable
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class: I
- Impact strength IK07
- Protection against mechanical impacts < 2 joule
- : Safety mark
- CE: Conformity mark
- Weight: 2.0 kg
- This product contains light sources of energy efficiency class(es) D
Safety
- The installation and operation of this luminaire are subject to national safety regulations.
- Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation.
- If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
Specifications
Lamp
- Module connected wattage: 24.6 W
- Luminaire connected wattage: 28.4 W
- Rated temperature: ta = 25 °C
- Ambient temperature: ta max = 25 °C
50 146.1 K3
- Module designation: 2x LED-0696/930
- Colour temperature: 3000 K
- Colour rendering index: CRI > 90
- Module luminous flux: 3620 lm
- Luminaire luminous flux: 2571 lm
- Luminaire luminous efficiency: 90,5 lm / W
50 146.1 K4
- Module designation: 2x LED-0696/940
- Colour temperature: 4000 K
- Colour rendering index: CRI > 90
- Module luminous flux: 3770 lm
- Luminaire luminous flux: 2678 lm
- Luminaire luminous efficiency: 94,3 lm / W
Installation
- LED are high-quality electronic components!
- Please avoid touching the light output opening of the LED directly during installation or relamping.
- Undo screws and lift off luminaire top.
- Loosen earth connection (plug connection) and
- LED-connection between luminaire top and luminaire base.
- Lead the mains supply cable through the cable entry of the luminaire base.
- Note position of application of the luminaire “arrow down”.
- Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
- Be sure to use the gasket rings supplied.
- Make earth conductor connection.
- Push silicone sleeves over the lines and make electrical connection.
- For digital control please use the connecting terminal DA, DA.
- In case this terminal is not used the luminaire will be operated at full light output.
- Make earth connection (plug connection) and LED-connection between luminaire top and luminaire base again.
- Install luminaire top part, adjust it and tighten screws evenly.
Maintenance
Cleaning /Maintenance
- Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
- Disconnect the system and open the luminaire.
- Uninstall the reflector.
- Please follow the installation instructions for the LED module.
- Install the reflector. Defective glass must be replaced. Close the luminaire.
Replacement of the glass
- Undo screws and lift off luminaire top.
- Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.
- Loosen reflector screws, separate earth connection and remove reflector.
- Loosen screws of the glass retaining springs and remove glass retaining springs from the luminaire top.
- Remove damaged glass. Insert replacement glass.
- Reinstall glass retaining springs and tighten screws on both sides.
- Insert reflector into luminaire top part, make earth connection to reflector and tighten reflector screws (0,6 Nm).
- Make earth connection (plug connection) and
- LED-connection between luminaire top and luminaire base again.
- Install luminaire top part, adjust it and tighten screws evenly.
Spares
- LED power supply unit: DEV-0388/700
- LED module 3000 K: LED-0696/930
- LED module 4000 K: LED-0696/940
- Reflector: 76 001 510
BEGA Gantenbrink-Leuchten KG
- Postfach 31 60 · 58689 Menden
- info@bega.com
- www.bega.com
References
Read User Manual Online (PDF format)
Loading......