BEGA 31406 Wall Luminaire Instruction Manual

BEGA 31406 Wall Luminaire

Product Information

metal’s natural surface colour. Time and weather factors create the
natural patina characteristic for copper.
Spare Parts| Ersatzglas LED-Leuchtmittel 3000K Fassung Dichtung Glas

Product Usage Instructions

This wall luminaire can be used for various lighting tasks in or on buildings. It is known for its high corrosion resistance.

Safety:
The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. If any modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.

Replacing the Lamp:

1. Ensure that the luminaire is switched off and disconnected from the power source.
2. Unscrew and remove the existing lamp from the luminaire.
3. Insert a new lamp with a maximum power output of 100 W into the screw base E27.
4. Tighten the lamp securely.

Replacing Spare Parts:

1. Refer to the spare parts list for the specific part you need to replace.
2. Ensure that the luminaire is switched off and disconnected from the power source.
3. Remove the faulty part by unscrewing or detaching it according to the manufacturer’s instructions.
4. Attach the replacement part using the appropriate tools and following the manufacturer’s instructions.
5. Switch on the luminaire to test if the replacement part is functioning properly.

For detailed technical and lighting data on the lamps, please refer to the data sheets available on our website.

Application

• Wall luminaire for many lighting tasks in or on buildings.
• Luminaire is distinguished by its high corrosion resistance.

Product Description

• Luminaire made of copper, brass, and stainless steel
• Antique glass
• Wall mounting with a mounting plate made of stainless steel, Steel grade number 1.4301
• Mounting plate with 2 fixing holes ø 5.5 mm · 70 mm spacing
• 1 cable entry for mains supply cable up to ø 10,5 mm
• Connecting terminal 2.5@ with plug connection
• Earth conductor connection
• Lampholder E 27
• Safety class I
• Protection class IP 44
• Protected against granular foreign bodies ≥ 1 mm and splash water
• Impact strength IK02
• Protection against mechanical impacts < 0.2 joule
  • Safety mark
  • Conformity mark
• Weight: 3.8 kg

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp Specification

• Luminaire with screw base E 27
• Lamp output max. 100 W
• This product contains a light source of energy efficiency class E
• Supplied lamp
• BEGA LED lamp 13 590
• LED Retrofit 12 W · 1400 lm · 3000 K
• Luminaire efficiency: 66%

Additional BEGA LED lamps are available for this luminaire:

• 13 584 LED 7 W · 805 lm · 3000 K
• 13 586 LED 7 W · 805 lm · 3000 K dimmable
• 13 588 LED 8 W · 1055 lm · 3000 K
• 13 592 LED 12 W · 1400 lm · 3000 K dimmable

Detailed technical and lighting data for the lamps can be found in the data sheets on our website.

Installation

• To avoid fingerprints on the luminaire use enclosed protective gloves during installation.
• Undo the screwing on the luminaire top.
• Remove the top and crystal bubble glass.
• Undo the screw at the wall box.
• Remove the mounting plate from the wall box. Lead the main supply cable through the cable entry of the mounting plate.
• Note the position of application of the mounting plate “arrow down”.
• Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
• Make an earth conductor connection and make an electrical connection.
• Note the position of application of the luminaire “arrow down”.
• Make earth conductor connection between luminaire housing and mounting plate.
• Push the plug into the coupler as far as it will go.
• Place the luminaire housing on the mounting plate align and tighten the screw.
• Insert lamp.
• Assemble crystal bubble glass and luminaire top.
• Make sure that gasket is in the correct position.

Dimension

Relamping And Maintenance

• Disconnect the electrical installation.
• Open the luminaire and clean it.
• Use only solvent-free cleaning agents. Change the lamp.
• Check the gasket and replace, it if necessary.
• Close the luminaire.
• For cleaning, do not use high-pressure cleaners.

Copper

• The luminaire parts made of solid copper are delivered with the metal’s natural surface color.
• Time and weather factors create the natural patina characteristic of copper.

Spares

• Spare glass 11 002 594 .3
• LED lamp 3000K 13 590
• Lampholder 63 000 105
• Gasket glass 82 000 147

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>