BEGA 50523.2 Recessed Ceiling and Wall Luminaire for Indoor Use Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50523.2 Recessed Ceiling and Wall Luminaire for Indoor Use
DIMENSION
Instructions for use
Application
Recessed ceiling and wall luminaire · indoor luminaire with hand-blown opal
glass, satin matt and aluminium housing for connection to an external LED
power supply unit. For installation into ceilings with a shallow depth in
interior areas.
Product Description
- LED recessed luminaire without power supply unit
- Luminaire housing made of aluminium
- Cover ring stainless steel
- Opal glass, satin matt, with screw neck
- Silicone gasket
- Recessed opening ø 166 mm
- Required installation depth 65 mm
- Luminaire housing with 3 fixing claws and guide screws
- 1 connecting cable with strain relief and plug
- connector system for BEGA power supply unit,
- on/off or DALI
- Safety class III 3
- c – Conformity mark
- Weight : 0.95 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
- Module connected wattage 8.3 W
- Luminaire connected wattage 11 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 50 °C
- When installed in heat-insulating
- material ta max = 25 °C
50 523.2 K3
- Module designation LED-0445/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1355 lm
- Luminaire luminous flux 570 lm
- Luminaire luminous efficiency 51,8 lm / W
50 523.2 K4
- Module designation LED-0445/940
- Colour temperature 4000 K
- Colour rendering index CRI > 90
- Module luminous flux 1430 lm
- Luminaire luminous flux 602 lm
- Luminaire luminous efficiency 54,7 lm / W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping. A separate power supply unit is required to operate
the luminaire – accessory 13 176 or 13 172. The recessed opening is covered by
the frame of the luminaire housing. Fixing of the luminaire in the structure
is achieved by using three adjustable wedge-shaped claws.
Installation in solid walls or ceilings
To accommodate the luminaire and the external power supply unit we recommend
using the installation housing 13 027.
Please note: To ensure that the luminaire is securely held in the
plastered installation housing, it is essential to unscrew the screws on the
underside of the fastening claws and remove the adapter for the fastening
claws (see drawing).
Installation in suspended ceilings
A recessed opening of ø 166 mm with a minimum installation depth of 65 mm is
required.The lateral distance between the luminaire housing and parts of the
building must be at least 50 mm. The claws grip behind the panel. The minimum
thickness of the panel must be 3 mm and the maximum thickness 20 mm. A panel
with less than 5 mm thickness must be reinforced on the reverse side.
- Remove glass from luminaire housing by turning it counter-clockwise.
- For connection to external LED-power supply unit – accessory 13 176 or 13 172 – the luminaire is equipped with a 2-pin connector.
- Note operating instructions of the LED-power supply units.
- Connect plug part of the luminaire with power supply unit.
- Push external LED power supply unit and luminaire housing into the ceiling cut-out.
- Tighten guide screws.
- When tightening the screws, the fixing claws must swivel onto the inside of the suspended ceiling. The luminaire is fixed.
- When undoing the guide screws, the fixing claws swivel back and the luminaire can be removed.
- Screw the glass into the luminaire housing by turning it clockwise.
- Make sure the seal is properly located.
Cleaning Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt. Defective
glass must be replaced.
Replacement of the LED module · Maintenance
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect from main supply. Unscrew glass from
luminaire housing by turning it counter-clockwise. Clean glass and luminaire
regularly with solvent-free cleansers from dirt. Please follow the
installation instructions for the LED module. Check gasket. Screw in glass by
turning it clockwise beyond the stop. A broken glass must be replaced.
Accessories
- Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
- 13 176 Power supply unit on/off
- 13 172 Power supply unit DALI
- The power supply units are only suitable for the operation of one LED luminaire.
- 13 027 Installation housing
For the accessories a separate instructions for use can be provided upon request.
Spares
- Spare glass 11 003 068 40R G
- LED module 3000 K LED-0445/930
- LED module 4000 K LED-0445/940
- Gasket glass 83 001 459
CONTACT
- BEGA Gantenbrink-Leuchten KG
- Postfach 31 60
- 58689 Menden
- info@bega.com.
- www.bega.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>