SUNELL IPV57_xxEE DR Dome Camera User Guide
- June 13, 2024
- SUNELL
Table of Contents
SUNELL IPV57_xxEE DR Dome Camera
Product Information
The Vandal Dome Network Camera is a surveillance camera designed for indoor
and outdoor use. It features a durable and vandal-resistant housing to protect
the camera from tampering or damage. The camera is equipped with an image
sensor that captures high-quality video footage for monitoring purposes. It is
important to follow the precautions and usage instructions provided in the
user manual to ensure optimal performance and longevity of the device.
Precautions
Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.
WARNING
It alerts you to moderate dangers which, if not avoided, may cause minor or
moderate injuries.
CAUTION
It alerts you to risks. Neglect of these risks may cause device damage, data
loss, device performance deterioration, or unpredictable results.
NOTE It provides additional information.
WARNING
- Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
- Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be
- Use accessories delivered with this device. The voltage must meet input voltage requirements for this device damaged
- If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
- When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
- Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
- If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.
CAUTION
SUNELL IPV57_xxEE DR Dome Camera
this device. Otherwise, the service life of the image sensor may be
shortened. If this device is installed in places where thunder and lightning
frequently occur, ground the device nearby to discharge high energy such as
thunder strikes in order to prevent device damage.
CAUTION
- Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
- Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
- Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
- Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
- Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
- Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
- If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
- Remove the power plug if the device is idle for a long time.
Special Announcement
- All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
- The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
- This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
- This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.
NOTE For more information, please refer to website.
-
Open Package Examination
Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
Table 1 -1 Packing list
| Component | Quantity | Remark |
|---|---|---|
| Vandal Dome Network Camera | 1 | |
| Quick Setup Guide | 1 | |
| T15 Screw driver | 1 | Large Dome |
| T10 Screw driver | 1 | Mini Dome |
| Installation location sticker | 1 | |
| Stainless self-tapping screw PA4.0×30mm | 3 | |
| Swell plastic buttonφ5.6×29mm | 3 | |
| Network access port protective cover | 1 | |
| Waterproof rubber seal | 1 |
-
Device Structure
Device Ports
NOTE Len adjustment is only applied for large dome.
Figure 2-1 Lens adjustment
Figure2-3 Multi-head cable 2
Description
| Port Name | Description |
|---|---|
| Focusing lever | Adjust the focus of lens, the default status is lock. |
| Zoom lever | Adjust the lens focal length, the default status is lock. |
Figure2-2 Multi-head cable 1
NOTE Different device may have different multi-head, please refer to the
actual product.
Table 2-3 Multi-head cable 2 description
| ID | Core | Description | Remark |
|---|---|---|---|
| 1 | Network access port | Connects to a standard Ethernet cable or POE. | |
| 2 | Audio input port | Receives an analog audio signal from devices such as a | |
| sound pickup device. | Applied for audio function | ||
| 3 | Audio output port | Connects to an external audio device such as a speaker. | |
| 4 | Power supply (DC 12V) | Connects to a 12V direct current (DC) power supply | |
| or 24V alternating current (AC) power supply. | |||
| 5 | Gray core | Alarm output terminal A(normal open) |
Applied for alarm function
Purple core| Alarm output terminal B(normal open)
Yellow core| Alarm input positive terminal
Orange core| Alarm input ground terminal
Figure2-3 Multi-head cable 2
Table 2-3 Multi-head cable 2 description
| ID | Core | Description | Remark |
|---|---|---|---|
| 1 | Network access port | Connects to a standard Ethernet cable or POE. | |
| 2 | Audio input port | Receives an analog audio signal from devices such as a | |
| sound pickup device. | Applied for audio function | ||
| 3 | Audio output port | Connects to an external audio device such as a speaker. | |
| 4 | Power supply (DC 12V) | Connects to a 12V direct current (DC) power supply | |
| or 24V alternating current (AC) power supply. | |||
| 5 | Gray core | Alarm output terminal A(normal open) |
Applied for alarm function
Purple core| Alarm output terminal B(normal open)
Yellow core| Alarm input positive terminal
Orange core| Alarm input ground terminal
Camera Dimensions
NOTE Different device may have different dimensions, please refer to the actual product.
Figure 2-4 Dimensions of Large Dome（Unit:mm）
Figure 2-5 Dimensions of Mini Dome(Unisom）
Device Installation
WARNING
To avoid moisture influence, install the dome cover at least half an hour
after the camera is installed and powered on.
The vandal dome camera can be installed in the ceiling , wall , wall bracket or ceiling bracket. This section describes how to install the camera in the ceiling.
Installation Steps
Step 1 Use the T15 screw driver in the accessory package to unscrew the three
screws on the dome cover. The camera is opened, as shown in figure 3-1.
Figure 3-1 Opening camera
Step 2 Stick the Installation location sticker on the ceiling or wall,
Drill three holes based on the marks on the sticker. Drive the swell plastic
buttons into the holes.
Step 3 Fetch three black self-tapping screws from the accessory package.
Then fix the screws to fasten the camera on the ceiling as shown in figure
3-2.
Figure 3-2 Installing housing
Step 4 Connect the network access port and power supply of the multi-head
cable.
Step 5 Adjust the lens focal length and video angle range.
lining aside, as shown in figure 3-3.
Figure 3-3 Removing lining
View the video, loosen the slotted screw slightly as shown in figure 3-4 & figure 3-5, make camera’s triaxial adjustments, adjust the screen to the scene you want to monitor, and then tighten the screws. Three-axis adjustment direction and angle are shown in figure4 & figur Fie 3g-u5r. e 3-4 Adjusting lens.
Large dome Figure 3-5 Three-axis adjustment
0°~350° Mini dome
Step 5 Loosen the focus lever, and gently move the zoom lever to adjust
the lens focal length to the desired position. Move the focus lever slightly
to focus the lens clearly. Tighten the focus lever after completing the
focusing operation, as shown in figure 3-4(This step is only applied for large
dome).
NOTE
- While focusing lever is in the process of focusing, an image might be blur, move the zoom lever to fine-tune the image, when image is clear, lock the zoom lever.
- If the lens of camera is auto focus lens, Set the focus value in Sensor > Lens control page in web page.
Step 6 Assemble the lining with the main body and buckle the four button placements with the main body bracket. Aim the two screws hole with boss at the groove on the main body. Then fasten the dome cover , as shown in figure 3-6.
Figure3-6 Assembling lining and cover
Quick C 4 onfiguration(e.g IE)
4.1 Login
Step 1 Open the Internet Explorer, enter the IP address of IP camera
(default value: 192.168.0.120? in the address box, and press Enter. The login
page is displayed. as shown in figure 4-1 . Step 2 Input the user name and
password.
NOTE The default user name is admin. The default password is admin.
Change the password when you log in the system for first time to ensure system
security. You can change the system display language on the login page.
Figure 4 -1 Login
Step3 Click Login, the main page is displayed.
Modify IP address
Choose Configuration > Device > Local
Network, the Local Network page is displayed.
Enter the IP address in the IP Address box and click Apply as shown in figure
4-2.
After the success of the IP address setting, please use the new IP address to
log in the Web interface.
Figure 4-2 Local Network
Browsing Video
To ensure the real-time video can be played properly, you must perform the
following operation when you log in the web for the first time:
Step 1 the Internet Explorer. Choose Tools > Internet options >
Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3.
Step 2 In the Internet Explorer, choose Tool > Internet Options >
Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 4-4.
Figure 4-3 Adding a trusted site
Figure 4-4 Configuring ActiveX control and plug-in
Step 3 Download and install the player control as prompted.
NOTE
If the repair tips displayed when installing the control , please ignore the
prompt, and continue the installation, the login page is displayed when the
control is loaded.
To browse a real-time video, click Live Video. The Live Video page is
displayed, as shown in figure 4-5.
Figure 4-5 Live Video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>