SW-MOTECH HPR.00.220.13400-B Storm Hands Black Instruction Manual

: June 1, 2024
: SW-MOTECH

Table of Contents

SW-MOTECH HPR.00.220.13400-B Storm Hands Black
Product Usage Instructions
FAQ
GENERAL INFORMATION
RODUCT SPECIFIC INFORMATION
PARTS
Mouting
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SW-MOTECH HPR.00.220.13400-B Storm Hands Black

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-product

Specifications

Model Numbers: HPR.00.220.13400/B, HPR.00.220.82500/B, HPR.00.220.10000/B
Colour : Black
Material: High-quality plastic
Dimensions: Vary based on model
Weight : Vary based on model

Product Usage Instructions

Assembly

Follow the assembly instructions provided in the manual. Ensure all parts are securely attached.

Installation

Choose a suitable location for the product. Use appropriate tools to install it securely.

Operation

Refer to the user manual for specific operating instructions. Make sure to follow safety guidelines.

Maintenance

Regularly clean the product with a damp cloth. Avoid using harsh chemicals that may damage the surface.

Troubleshooting

If you encounter any issues, refer to the troubleshooting section of the manual or contact customer support.

FAQ

Q: Can this product be used outdoors
A: It is recommended to use this product indoors to prevent damage from environmental factors.
Q : How do I disassemble the product for storage?
A : Follow the reverse steps of the assembly instructions to disassemble the product for storage.
Q: What is the warranty period for this product?
A : The warranty period is [insert warranty period here]. Please refer to the warranty information in the manual for details.

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our website.
Installation and/or maintenance of this product requires good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION : Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

RODUCT SPECIFIC INFORMATION

After the installation check all operations of all handlebar controls, specifically the throttle, front brake, kill switch and clutch, to ensure they are operating correctly and are in accordance with the OEM specifications. Do not ride the vehicle if any controls are not operating correctly. It may be necessary to move the brake and clutch controls toward the handlebar end by a few millimetres to achieve a correct fit. Make sure the handlebar can fully turn in either direction. If parts of the product make contact with the tank at full steering lock, it may be necessary to rotate the handlebar up (forward) slightly to allow adequate clearance.

PARTS

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-1

All measurements in millimetres
The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table ca be used as long as it is within the vehicle manufacturer’s specifications.

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-3

Mouting

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-4
NOTE : The Installation is shown for the left side. The installation on the right side of the vehicle is analogous to the left side of the vehicle. If mounted, remove the original hand guards and their mounting plates from the vehicle. Attach the handlebar clamps (1] with the connectors (2] loosely to the handlebar.
ATTENTION : Pay attention to the grooves on the inside of the tapered handlebar clamp. The grooves must be positioned on the inner side, towards the centre of the vehicle. Do not fully tighten the screws yet.

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-5

Attach the backbones (6] with the original handlebar end weights (Orig.] to both ends of the handlebar, as shown in the drawing.
ATTENTION : Use a liquid thread locker! Do not fully tighten the screws yet.

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-6

Attach the inner ends of the bars (6) to the connectors [2).
ATTENTION: Use a liquid thread locker! Do not fully tighten the screws yet. Position the bars in the preferred position and tighten all screws in the following order: (71, (81, (3) & (4).

Instructions

Mounting Instructions

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-7
ATTENTION: The assembly of this product can be complicated and requires a good technical understanding. If you are not sure of how to do this, have a specialty garage perform the mounting and service. SW-MOTECH accepts no liability for damages caused by improper installation.
ATTENTION : After the installation check all operations of all handlebar controls, specifically the throttle, front brake, kill switch and clutch, to ensure they are operating correctly and are in accordance with the OEM specifications. Do not ride the motorcycle if any controls are not operating correctly. Make sure the handlebar can fully turn in either direction. Check periodically (50 km) that all bolts are tight. Subject to change. Not responsible for typos.

SW-MOTECH-HPR.00.220.13400-B-Storm-Hands-Black-fig-8

NOTE: Installation is shown on the left side. Repeat for right side with applicable parts. Attach the handguard shells (1] & [2] to the backbones [befor mounting the backbones to the vehicle]. as shown in the drawing.
ATTENTION: Tighten the screws carefully by hand (max. 2 Nm]. Do not overtighten the screws!