Honeywell TH6320U2008 T6 Pro Programmable Thermostat User Guide

: June 5, 2024
: Honeywell

Honeywell TH6320U2008 T6 Pro Programmable Thermostat

Honeywell TH6320U2008 T6 Pro Programmable Thermostat
product

Thermostat controls

System status information
Cool On/Heat On/Em Heat On, Recovery, Compressor Protection
Schedule information Following time based schedule
Actual time
Mode
Select system mode Heat/Off/Cool/Auto/EM Heat (emergency heat)
Menu
Press to display options. Start here to set a program schedule
Indoor temperature setpoint
Press + or – to change temperature setting
Actual indoor temperature
Temperature/Navigation buttons
Press to increase or decrease temperature setpoint and to navigate menus and menu options
Fan
Select Fan mode Auto/On/Circulate

The screen will wake up by pressing any of the five buttons. If powered by the C wire, the screen stays lit for 45 seconds after you complete changes. If powered by battery only, the screen stays lit for 8 seconds. Depending on how your thermostat was installed, the screen light may always be on.

OPERATION

System operation settings

Press the Mode button to cycle to the next available System mode.
Cycle through the modes until the required System mode is displayed and leave it to activate.

NOTE: Available System modes vary by model and system settings.
System modes:

Auto
Heat
Cool
Em Heat
Off

Fan operation settings

Press the Fan button to cycle to the next available Fan mode.
Cycle through the modes until the required Fan mode is displayed and leave it to activate.

NOTE: Available Fan modes vary with system settings.
Fan modes:

Auto: Fan runs only when the heating or cooling system is on.
On: Fan is always on.
Circ: Fan runs randomly about 33% of the time.

Set the time and date

Time

Press Menu on your thermostat.
Press or to go to TIME. Press Select.
Press or to choose between 12 or 24 hour.
Press Select.
Use or to adjust the hour. Press Select.
or to adjust the minutes. Press Select to exit Time menu.

Date

If previously setting time, continue to Step
If at the Home screen, press Menu on your thermostat.
Press or to go to DATE. Press Select.
Use or to adjust year. Press Select.
Use the or to adjust month. Press Select
Use the or to adjust day. Press Select to save and exit Date menu.

Program Schedule

You can program four time periods each day, with different settings for weekdays and weekends. We recommend the pre-sets (shown in the table below), since they can reduce your heating/cooling expenses.

Wake – Set to the time you wake up and the temperature you want during the morning, until you leave for the day.
Away – Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
Home – Set to the time you return home and the temperature you want during the evening, until bedtime.
Sleep – Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level).

NOTE: To temporarily or permanently override any of the above program schedules, see page 4.

To adjust program schedules

Press Menu on your thermostat.
PROG is displayed. Press Select. Then ON is displayed. (If you do not want to use a schedule, press or to display OFF. Press Select.) Press Select.
Press or to select day or set of days to edit. Press Select.
Press or to select a schedule period to edit (Wake, Away, Home, and Sleep). Press Select.
ON is displayed. Press Select to keep the schedule period on. Or press and then Select to turn off the schedule period.
Time starts blinking. Press or to adjust the schedule period start time. Press Select.
Temperature starts blinking. Press or to adjust the “Heat” setpoint temperature. Press Select. Press or to adjust the “Cool” temperature setpoint. Press Select.
Repeat steps 4 through 7 for the remaining schedule periods.
Press Home when you’re finished to save and return to the home screen.
Schedule can be adjusted and turned ON or OFF by returning to Menu and following the steps provided above.

Program schedule override (temporary)

Press or to adjust the temperature.
Once at the desired setpoint temperature, no further action is needed. The new setpoint temperature will be held until the next scheduled time period begins. For more information on schedule time periods, see “Program Schedule”
To cancel the Temporary Hold, Press or and then press Cancel.

Program schedule override (permanent)

Press or to adjust the temperature.
TEMPORARY HOLD is displayed and the setpoint temperature flashes. While it’s flashing, press Hold (Mode) button to change to Permanent Hold.
To cancel the Permanent Hold, press+ or – and then press Cancel.

Adjusting keypad lockout

Press Menu on the thermostat.
Press +or -to go to LOCK. Press Select.
Press +or- to go to OFF, PART, or ON, and then press Select.
- OFF: Unlocked, and full access allowed.
- PART: Partial lockout, allowing only the temperature to be changed.
- ON: No access allowed.
To unlock the keypad, press the CENTER button and then enter the password “1234”. To enter the password, press or to change the first digit of the number. Then press Select. Repeat this process to enter the second through fourth digits of the number. Once all four numbers have been entered, press Select again.
This will unlock the keypad.
If the code is incorrect, the screen will flash the lines “–“.
Press Back to go back a step to enter the correct number and press Select.

NOTE: On some models, the keypad lockout setting is not available in the user menu if the installer didn’t configure the thermostat to allow this setting.

Adaptive Intelligent Recovery

Over time, the T6 Pro Thermostat “learns” how long it takes your system to reach the temperature you want. It turns on the heating or cooling system earlier to make sure you’re comfortable at the time you expect.

Built-in compressor protection
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting.
During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
Message flashes until safe restart time has elapsed.
Honeywell TH6320U2008 T6 Pro Programmable Thermostat
10

Battery replacement

Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed. If your thermostat was not wired to run on AC power, then batteries are required.
Install fresh batteries immediately when the low battery icon appears. The icon appears about two months before the batteries are depleted.
Even if the low battery icon does not appear, you should replace batteries once a year, or before leaving home for more than a month.
If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power.
NOTE: When replacing batteries, alkaline batteries are recommended.

When the low battery warning appears, carefully pull the thermostat from the wall mount.
Insert fresh alkaline AA batteries and reinstall thermostat.

Honeywell TH6320U2008 T6 Pro Programmable Thermostat
12

Alerts
If there is an alert or reminder, the alert icon appears on the Home screen.

Low Battery Warning

The batteries need to be replaced when BATT, the alert icon , and the battery icon are displayed on the Home screen.
When the battery power is very low, the thermostat’s backlight is disabled to save battery power.
When battery power is critically low, only BATT, the alert icon , and the battery icon are displayed.

Air Filter Reminder

The alert icon warning appears on the Home screen.
Press Menu, and then press until display shows ALRT.
Press Select to display which alert(s) are present.
The message REPL (REPLACE AIR FILTER) appears.
The reminder can be snoozed or cleared.
Reside recommends changing the air filter before clearing the reminder.
To snooze, press Select. The word SNZE (SNOOZE) appears.
Press Select again to snooze the reminder for 7 days.
To clear, press Select, and then press to go to CLER (Clear).
Press Select to clear the air filter reminder.

Snoozing and Clearing Alerts or Reminders

Press Menu, and then press until display shows ALRT.
Press Select to display which alert(s) are present.
The word SNZE (SNOOZE) appears.
Press Select again to snooze the reminder for 7 days.
To clear the alert, press Select, and then press to go to CLER (Clear).
Press Select to clear the reminder.* Some alerts cannot be snoozed or cleared.
Please call your local heating and cooling professional if this occurs. The heating and cooling system may require service.

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.

Display is blank
- Check circuit breaker and reset if necessary.
- Make sure power switch for heating & cooling system is on.
- Make sure furnace door is closed securely.
- Make sure fresh AA alkaline batteries are correctly installed
Heating or cooling system does not respond
- Press Mode button to set system Heat (see page 2). Make sure the desired temperature is set higher than the inside temperature.
- Press Mode button to set system Cool (see page 2). Make sure the desired temperature is set lower than the inside temperature.
- Check circuit breaker and reset if necessary.
- Make sure power switch for heating & cooling system is on.
- Make sure furnace door is closed securely.
- Wait 5 minutes for the system to respond.
Temperature settings do not change
- Make sure heating and cooling temperatures are set to acceptable ranges:
- Heat: 40 °F to 90 °F (4.5 °C to 32.0 °C)
- Cool: 50 °F to 99 °F (10.0 °C to 37.0 °C)
“Cool On” or “Heat On” is flashing
- Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor .

Electrical Ratings

Terminal

| Voltage
(50 Hz/60 Hz)|

Running Current

---|---|---

W Heating

| 20 Vac – 30 Vac| 0.02 A – 1.0 A
W2 (Aux) Heating| 20 Vac – 30 Vac|

0.02 A – 1.0 A

E Emergency Heat

| 20 Vac – 30 Vac| 0.02 A – 0.5 A
Y Compressor Stage 1| 20 Vac – 30 Vac|

0.02 A – 1.0 A

Y2 Compressor Stage 2

| 20 Vac – 30 Vac| 0.02 A – 1.0 A
G Fan| 20 Vac – 30 Vac|

0.02 A – 0.5 A

O/B Changeover

| 20 Vac – 30 Vac| 0.02 A – 0.5 A
L/A Input| 20 Vac – 30 Vac|

0.02 A – 0.5 A

5-year limited warranty

https://www.honeywellhome.com/support

CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before beginning installation.
CAUTION: EQUIPMENT DAMAGE HAZARD
Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.
CAUTION: MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.
CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers.
The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.

Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422 https://www.honeywellhome.com/support
33-00182EFS—10 M.S. Rev. 04-22 | Printed in United States
www.resideo.com