BEGA 24 620 Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 24 620 Wall Luminaire
Product Information
Product Usage Instructions
Dimensions
Product Description
Safety
Installation
Specifications
Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24 620 Wall Luminaire

BEGA-24-620-Wall-Luminaire-product

Product Information

The Wandleuchte Wall luminaire Applique is a wall luminaire with two-sided light output. It is designed for illumination and design tasks in architecture. The light directed downwards is intended to illuminate the wall and the horizontal surface in front of it, while the light directed upwards is intended to illuminate the wall and ceiling surfaces.

Safety: The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer does not accept liability for damage caused by improper use or installation. Any subsequent modifications to the luminaire should be done by the person responsible for the modifications.

Product Usage Instructions

Fix the mounting plate onto the mounting surface using the enclosed or suitable fixing material.
Tighten the screw cable gland.
Make the earth conductor connection and electrical connection to the connecting terminal (plug connection).
If digital control is desired, use the connecting terminal DA, DA. If not used, the luminaire will be operated at full light output.
Ensure that the gasket is positioned correctly.
Push the plug into the coupler as far as it will go.
Place the luminaire onto the mounting plate and fix it.

Dimensions

BEGA-24-620-Wall-Luminaire-fig-1

Application

Wall luminaire with two-sided light output.
For illumination and design tasks in architecture.
The light directed downwards is intended to illuminate the wall and the horizontal surface in front of it.
The light directed upwards is intended to illuminate the wall and ceiling surfaces.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite, silver or white
Matt safety glass
Reflector surface made of pure aluminium
Mounting plate with 2 fixing holes ø 5.4 mm · 70 x 125 mm spacing
2 screw cable glands with strain relief for through-wiring power connecting cable ø 7–12 mm
1 screw cable gland closed at the factory with a dummy plug
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit: 220-240 V 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
: Safety mark
CE: Conformity mark
Weight: 4.4 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

BEGA-24-620-Wall-Luminaire-fig-4.

Undo hexagon socket head screws (wrench size 3 mm) up to the stop and disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
The installed black gasket insert is intended for cables ø < 10 mm.
For cables ø 10-12 mm the enclosed grey gasket insert must be used.
In case of through-wiring replace the factory installed dummy plug with the enclosed corresponding gasket insert.
At the same time, use the enclosed synthetic cone-thrust collar between gasket insert and thrust screw (wrench size 22 mm) (see sketch).
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Tighten screw cable gland.
Make earth conductor connection and electrical connection to the connecting terminal (plug connection).
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Make sure that gasket is positioned correctly.
Push plug into coupler as far as it will go.
Place the luminaire onto the mounting plate and fix it.

Specifications

Lamp

Module connected wattage: 35.4 W
Luminaire connected wattage: 39 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 35 °C

24 620 K3

Module designation: 2x LED-0800/830
Colour temperature: 3000 K
Colour rendering index: CRI > 80
Module luminous flux: 5960 lm
Luminaire luminous flux: 4249 lm
Luminaire luminous efficiency: 108,9 lm / W

24 620 K4

Module designation: 2x LED-0800/840
Colour temperature: 4000 K
Colour rendering index: CRI > 80
Module luminous flux: 6120 lm
Luminaire luminous flux: 4363 lm
Luminaire luminous efficiency: 111,9 lm / W

Lighting technology

Wall luminaire with broad spread light distribution.
Half beam angle of the light distribution in both half spaces 70°.

Please note

Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Maintenance

Cleaning /Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares