HENDI 222829 Planetary Mixer User Manual

HENDI 222829 Planetary Mixer User Manual

Read user manual and keep this with the appliance

For indoor use only

NOTE: This manual is translated from original English manual using AI and machine translations.

Instruction

Technical specifications

Item no

Remark: Technical specification is subjected to change without prior notification.

Safety instructions

• Only use the appliance for the intended purpose it was designed for, as described in this manual.

• The manufacturer is not liable for any damage caused by incorrect operation and improper use.

• DANGER! RISK OF ELECTRIC SHOCK! Do not attempt to repair the appliance by yourself. Do not immerse the electrical parts of the appliance in water or other liquids.
  Never hold the appliance under running water.

• NEVER USE A DAMAGED APPLIANCE! Check the electrical connections and cord regularly for any damage. When damaged, disconnect the appliance from the power supply. Any repairs should only be carried out by a supplier or qualified person to avoid danger or injury.

• WARNING! When positioning the appliance, route the power cable safely if necessary to avoid unintentional pulling, being damaged, coming into contact with the heating surface, or causing a tripping hazard.

• WARNING! As long as the plug is in the socket the appliance is connected to the power supply.

• WARNING! ALWAYS switch off the appliance before disconnecting from the power supply, cleaning, maintenance or storage.

• Only connect the appliance to an electrical outlet with thevoltage and frequency mentioned on the appliance label.

• Do not touch the plug/electrical connections with wet or damp hands.

• Keep the appliance and electrical plug/connections away from water and other liquids. If the appliance falls into water, remove the power supply connections immediately. Do not use the appliance until it has been checked by a certified technician. Failure to follow these instructions will cause life threatening risks.

• Connect the power supply into an easily accessible electrical outlet so you can disconnect the appliance immediately in case of emergency.

• Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. Never pull the power cord to unplug it from the socket, always pull the plug instead.

• Never carry the appliance by its cord.

• Never try to open the housing of the appliance yourself.

• Do not insert objects into the housing of the appliance.

• Never leave the appliance unattended during use.

• This appliance should be operated by trained personnel in kitchen of the restaurant, canteens or bar staff, etc.

• This appliance should not be operated by persons with reduced physical, sensory or mental capabilities, or persons that have a lack of experience and knowledge.

• This appliance should, under any circumstances, not be used by children.

• Keep the appliance and its electrical connections out of reach of children.

• Never use accessories or any extra devices other than those supplied with the appliance or recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.

• Do not operate this appliance by means of an external timer or remote-control system.

• Do not place the appliance on a heating object (gasoline, electric, charcoal cooker, etc.).

• Do not cover the appliance in operation.

• Do not place any objects on top of the appliance.

• Do not use the appliance near any open flames, explosive or flammable materials. Always operate the appliance on a horizontal, stable, clean, heat-resistant and dry surface.

• The appliance is not suitable for installation in an area where a water jet could be used.

• Leave a space of at least 20 cm around the appliance for ventilation during use.

• WARNING! Keep all ventilation openings on the appliance free from obstruction.

Special safety instructions

• This appliance is not intended for household use.
• An equipotential bonding terminal is provided to allow cross bonding with other equipment.
• Do not operate the appliance without load to prevent overheating.
• CAUTION! ALWAYS switch the machine off and disconnect the power supply before touching any motoring parts.
• WARNING! Do not attempt to by-pass any safety interlock.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Do not load too much ingredients in order to prevent overflow of the food products.
• WARNING! DO NO LIFT APPLIANCE BY THE HANDLE.
• WARNING! Do not put the hands into the opening during operation. Disconnect the main power supply before reaching in.

Intended use

• This appliance is intended to be used for commercial applications, for example in kitchens of restaurants, canteens, hospital and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production of food.
• The appliance is designed for mixing, kneading and emulsifying/whipping food products operated in the food industry and shops. Any other use may lead to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.

Grounding installation

This appliance is classified as protection class I and must be connected to a protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current.
This appliance is fitted with a power cord with grounding plug or electrical connections with grounding wire. The connections must be properly installed and grounded.

GB Main parts of the product

(Fig.1 on page 3)

1. Base of the machine

2. Bowl

3. Guided pins (x2)

4. Bowl handles (x2)

5. Bowl guard handle

6. Bowl guard

7. Speed control knob

8. a. Timer increase button
   b. Timer decrease button

9. Control panel

10. Display of timer

11. ON / OFF Switch

12. Lift up / Lower bowl lever

13. Built in ingredient chute

14. RESET button (at the rear)

15. Bowl cradle
    Remark: The content of this manual applies for all listed items unless specified otherwise. The appearance may vary from the shown illustrations.

Spare parts or accessories

(Fig.2 on page 3)

16. Flat beater
17. Dough hook
18. Whisk

Circuit diagram

(Fig.3 on page 4)
A. Overload protection (Thermal cut-out)
B. Bowl lift lever safety switch
C. Bowl huard safety switch
D. STOP switch
E. ON switch
F. Reactor
G. Bowl position safety switch
H. Capacitor
I. Motor

Exploded diagram with part list

• The exploded drawing and part list consists of 4 main parts:

Main body of the machine (Fig.4 on page 4)

Gear assembly (Fig.5 on page 5)

Bowl lifting assembly (Fig.6 on page 6)

Bowl guard and turning axle (Fig.7 on page 6)

Precautions
The appliance should only be handled by highly qualified people who follow the safety measures described in this manual.

• In case of rotation of personnel, training should be provided in advance.

• The appliance is equipped with safety devices at dangerous points. However, it is recommended not to touch the blade and moving components.

• Before starting maintenance operations, disconnect it from the power supply.

• Carefully assess residual risks when protective devices are removed for cleaning and maintenance.

• Cleaning and maintenance require great concentration.

• Is absolutely necessary a regular control of the power supply cord. A frayed or damaged cord can expose users to great risk of electric shock.

• If the device shows anomalies, do not use it or try to repair it:
  please contact the supplier.

• Do not use the appliance for frozen foods or any products other than food.

• Do not wear loose fitting clothing such as scarf, etc and long hair should be tied up and keep away from the moving parts.
  The manufacturer and/or the seller are not responsible in the following cases:

• if the appliance has been handled by unauthorized personnel;

• if some parts have been replaced with non-original spare parts;

• if the instructions included in this manual are not followed precisely;

• if the cutter has not been cleaned and oiled with the right products.

Safety system installed

Mechanical safety system
The appliance is equipped with 3 safety switches. The machine only be started with all the safety switches are at the proper positions:

• Bowl position safety switch: The machine can be started up once the bowl is positioned at the correct position.
• Bowl guard safety switch: The machine can only be started up once the bowl guard is in the closed position.
• Lift up lever safety switch: The machine can only be started up once the lift up lever is located in the upwards position.

Even though CE version appliances are provided with electrical and mechanical protections (when the appliance is operating and for maintenance and cleaning operations), there are still RESIDUAL RISKS that cannot be eliminated completely; these risks are specified in this manual under “ WARNING! / DANGER! / CAUTION! ”. The moving parts of the machine can cause injuries.

Preparation before use

• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accessories. In case of incomplete or damaged delivery, please contact the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See ==> Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in the future.
• Keep the user manual for future reference.

NOTE! Due to manufacturing residues, the appliance may emit a light odor during the first few uses. This is normal and does not indicate any defect or hazard. Make sure the appliance is well ventilated.

Operating instructions

Special safety features
ATTENTION: This machine has the following 3 safety switches.
The machine only be started with all the safety switches are at the proper positions.

• Bowl position safety switch: The machine can be started up once the bowl is positioned at the correct position.
• Bowl guard safety switch: The machine can only be started up once the bowl guard is in the closed position.
• Lift up lever safety switch: The machine can only be started up once the lift up lever is located in the upwards position.
• Do not wear loose fitting clothing such as scarf, etc and long hair should be tied up and keep away from the moving parts

To avoid serious personal injury:

• DO NOT operate the machine without reading the instruction manual.
• ALWAYS switch OFF the machine and unplug from electrical power supply before cleaning, maintenance, repair or changing any attachments.
• ALWAYS keep hands, hair and loose clothing away from the moving parts.

a) About the bowl guard
Note: When bowl guard is open or not properly closed in lock position, the machine will not operate.

1. To open the bowl guard, hold the bowl guard handle and rotate it clockwise. To close the bowl guard, hold the bowl guard handle and rotate it anti-clockwise.
2. When the bowl guard handle is lined up at the right side of the machine, the bowl guard is in the is in the rocked position and ready for operation.

b) Install the bowl to the machine
Note: Install the bowl BEFORE fixing the attachments. Use the supplied bowl only.

1. Lower the bowl by pulling the bowl lift-up lever downwards until it stops. So that the bowl cradle is in a lower position.
2. Place the bowl carefully and slowly using the bowl handles at 2 sides and i) With the locking pin into the hole at the middle of the bowl cradle and ii) Align with guided pins on 2 sides of the bowl cradle.

c) Install different attachments (Flat beater, Dough hook or Whisk) to the machine

Note: It is more convenient and easier to install the attachments prior to adding the ingredients into the bowl.

1. Rotate the bowl guard clockwise gently, so that it is in the open position.
2. CAUTION! Use excessive force to open or close the bowl guard may damage the safety lock micro switch. Be careful when open or close the bowl guard.
3. Slide the attachments (Flat beater, Dough hook or Whisk) slowly upwards onto the planetary shaft fitting the shaft pin through the slot in the attachments.
4. Rotate the attachments to secure it onto the planetary shaft.

d) Pouring and mixing ingredients
Note: Follow the table of “Operating tips” in this manual. Overloading will lead to overflow or damage to the machine.
IMPORTANT: Make sure the speed control lever is set at the position 1.

1. Add all the appropriate ingredients into the bowl.
2. Lift upwards the bowl lift lever until the bowl locks into the position.
3. Rotate the bowl guard anti-clockwise and locks into the position.

ATTENTION: The machine will not start if the bowl guard is open / not closed properly or the bowl is at the lower position.

e) Set the timer, speed & start up the machine 

1. You can set the timer for the appropriate mixing time or operate without setting the timer.
   i) Operation with timer set: Press timer increase button toincrease the time or timer decrease button to decrease the time. Press the red ON/OFF button to confirm. Remaining time will be shown and dot blinks on the display.
   (Fig.8 on page 7).
   ii) Operation without timer set: The machine will switch OFF automatically in 10 minutes as the default timer is 10 minutes.
   Note:

   • Maximum setting time is 60 minutes. Default time is 10 minutes.
   • Press and hold timer increase button or timer decrease button for fast adjustment.

2. Then, select the appropriate speed by lifting or lowering the speed control lever. Three fixed speeds are available: 1 (Low), 2 (medium) and 3 (high).
   Rotation speed| Type of ingredient
   ---|---
   1 (Low)| Heavy: Mixing pizza, bread and pasta.
   2 (Medium)| Medium: 2nd stage of mixing for donut dough, etc.
   3 (High)| Light: Whipping cream, egg whites, me- ringed.

IMPORTANT: ALWAYS follow the recommended attachment used and speed setting according to the capacity table.
ATTENTION: Be careful about the risk of dust and flour escape when slitting of bags of ingredient into bowl. Wear protective mask or glasses if necessary.

3. After that, press the red (ON / OFF) button on the control panel to switch ON the machine. Press again to switch OFF the machine. The machine will rotate in clockwise direction.
4. CAUTION! ALWAYS STOP the machine BEFORE changing speeds. Failure to do so may damage the internal gear construction.
5. To change the speed during the operation:
   a) Press the red (ON / OFF) button on the control panel to switch OFF the machine.
   b) Change the speed by raising or lowering the speed control lever.
   c) Press the red (ON / OFF) button on the control panel to restart the machine.

RESET the safety cut-out (Hi-limiter or thermal cut-out)

(Fig.9 on page 7)
Please note that the RESET button is equipped with a protective cap to avoid overheat.

• Disconnect the appliance from the power supply.

• Allow the appliance to completely cool down.

• Unscrew the protective cap of the RESET button.

• Press the RESET button of the Hi-limiter (thermal cut-out).
  You should hear a click sound.

• Screw back the protective cap on the RESET button.

• Connect to the power supply and you can use it again.

Operating tips
Below table is just a reference about the maximum quantity for making the different food. There are many factors affecting such as the type of the flour, temperature of water, etc.

Cleaning & maintenance

• ATTENTION! Always disconnect the appliance from the power supply and cool down before storage, cleaning & maintenance.

• Do not use water jet or steam cleaner for cleaning and do not push the appliance under the water as the parts will get wet and electric shock might be resulted.

• If the appliance is not kept in a good state of cleanliness, this can adversely affect the life of the appliance and result in a dangerous situation.

• Food residues should be regularly cleaned and removed from the appliance. If the appliance is not cleaned properly, it will reduce its lifespan and may result in a dangerous condition during use.
  Cleaning

• Clean the cooled exterior surface with a cloth or sponge slightly dampened with a mild soap solution.

• Always remove all the attachments before cleaning, otherwise it will become stuck on the shaft and difficult to remove later.

• For reasons of hygiene, the appliance should be cleaned be- fore and after use.

• Avoid water contacting the electrical components.

• Clean the inside of container with a non-abrasive detergent and rinse with clean water.

• Never immerse the appliance in water or other liquids.

• No parts are dishwasher safe.

Recommended cleaning procedure:

Maintenance

• Check the operation of the appliance regularly to prevent serious accidents.

• If you see that the appliance is not working properly or that there is a problem, stop using it, switch it off and contact the supplier.

• All maintenance, installation and repair work must be carried out by specialised and authorised technicians, or recommended by the manufacturer.
  Transportation and Storage

• Before storage, always make sure that the appliance has been disconnected from the power supply and completely cooled down.

• Store the appliance in a cool, clean and dry place.

• Never place heavy objects on the appliance as this could damage it.

• Do not move the appliance while it is under operation. Disconnect the appliance from power supply when moving and hold it at the bottom.

• Special care must be taken when moving or transporting the machine due to its heavy weight. With at least 2 persons or using a cart. Move the machine slowly, carefully, and never incline more than 45°.

Troubleshooting

If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider

Rotate the bowl guard to the right until fully closed properly.
Bowl is not raised to the proper location.| Raise the bowl to the correct position by using the level.
The power plug is not connected properly.| Check to make sure the power plug is connected properly.
Machine stops during operation| Internal overload activates to prevent overheat.| Press OFF the button and then press RESET button at the back.
Damage or broken transmission belt| Contact the supplier.
Machine sound too noisy| Machine is not placed on a hori- zontal surface.| Adjust the surface or move to another horizontal surface.
Bowl is not placed correctly.| Make sure the bowl is placed into the bowl cradle correctly with the guided pins.
Attachments not fitted properly.| Remove and install the attachments into position again.
Bowl is overloaded.| Reduce ingredients capacity.
Damaged or worn transmission belt.| Contact the supplier.
Planetary gear needs lack of lubricant.
Attachments cannot install onto the plane- tarry shaft easily| Lack of lubricant and / or cleaning of the planetary shaft required.| Wipe planetary shaft with a clean damp cloth and lubricate the shaft with mineral oil or grease.
Lift up / Lower bowl lever not operation easily| Lack of lubricant on the bowl slides.| Lubricate bowl slides with mineral oil or grease.

Warranty

Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or replacement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in any way. Your statutory rights are not affected. If the appliance is claimed under warranty, state where and when it was purchased and include proof of purchase (e.g. receipt).
In line with our policy of continuous product development we reserve the right to change the product, packaging and documentation specifications without notice.

**Discarding & Environment

**When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose to your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment and ecological disposal, either directly or through a public system.

References

• hendi.com
• hendi.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>